Dimplex Siena Fire SNA20 User manual



ContactDetails

Pleasenotethatsomeofthecontactdetailson
thisPDFdocumentmaynotbecurrent.

Pleaseusethefollowingdetailsifyouneedto
contactus:

Telephone:08448793588
Email:[email protected]


Thecustomersupportsectionofourwebsitealsofeaturesawide
rangeofinformationwhichmaybeofusetoyouandisavailable
24hoursaday.Itincludes:

•Operatingandinstallationinstructions
•Easy‘Howtouse’guidesforstorageheaters
•Serviceandrepairs
•Wheretobuyourproducts
•Literaturedownloads
•Heatingrequirementcalculator

Visit‐www.dimplex.co.uk/support
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.dimplex.co.uk
Re
g
istered No: 1313016 En
g
land
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources

540
400 338
controls
controls
mains lead & plug
slot
screws
(3 no.)
bracket
lid
removable
back panel
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Dimensions
(millimetres)
Installation and Operating Instructions
Electrical
Dimplex Siena Fire
Model : SNA20
08/19092/0 Issue 0
Important Safety Advice:
When using electrical appliances, Basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
•If the appliance is damaged, check with the supplier
before installation and operation.
•Do not use outdoors.
•Do not use in the immediate surroundings of a bath,
shower or swimming pool.
•Do not locate the heater immediately below a fixed
socket outlet or connection box.
•Do not cover the heater. Do not place material or
garments on the heater, or obstruct the air
circulation around the heater, for instance by
curtains or furniture, as this could cause
overheating and a fire risk.
•This appliance is not intended for use by children
or other persons without assistance or supervision
if their physical, sensory or mental capabilities
prevent them from using it safely. Children should
be supervised to ensure that they do not play with
the appliance.
•Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from
the heater.
•In the event of a fault unplug the heater.
•Unplug the heater when not required for long
periods.
•Although this heater complies with safety
standards, we do not recommend its use on deep
pile carpets or on long hair type of rugs.
•The appliance must be positioned so that the plug
is accessible.
•If the supply cord is damaged it must be replaced
by the manufacturer or service agent or a similarly
qualified person in order to avoid a hazard.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your
supplier. Loose pebbles are packed separately within the carton.
When the heater is assembled the pebbles are placed on top of the
fuel bed.
In order to do this the lid must first be removed by unscrewing the
three screws at the rear of the lid (see Fig. 2), then slide the lid
towards the back of the stove and detach the lid from the stove.
Fig. 1
Please note: Used in an environment where backround
noise is very low, it may be possible to hear the motor
which operates the flame effect. This is normal and should
not be a cause for concern.
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and
operating instructions.
For your convenience, the heater is fitted with a rewireable plug
incorporating a 13 amp fuse. In the event of replacing the fuse in
the plug supplied, a 13 amp fuse approved by ASTA to BS1362
must be used.
To replace the lid,
position it so the two
brackets on the lid slot
into the two holes on
the heater and slide
forward to lock in
position. Replace the
three screws at the
rear of the lid.
The heater is
designed to be used
free-standing and is
normally positioned
against a wall.
Fig. 2

Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services: Tel. [phone]
Fax. [phone]
e-mail customer[email protected]
Republic of Ireland Tel. [phone]
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided
it has been installed and operated in accordance with these
instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our
customer services help desk on 0870 727 0101. It would assist
us if you can quote the model number, series, date of purchase,
and nature of the fault at the time of your call. The customer
services help desk will also be able to advise you should you need
to purchase any spares.
Please do not return a faulty product to us in the first instance as
this may result in loss or damage and delay in providing you with
a satisfactory service.
Please retain your receipt as proof of purchase.
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
Operation
The unique flame effect may be enjoyed whether or not the heating
elements are in operation.
Controls
The heater controls are located on the back of the heater (see Fig.
2).
Three switches provide a choice of heat settings. A switch is in the
ON position when the side with the markings on (i.e. I, I, or II ) is
pushed in.
Fig. 3
Switch 1 ( I )
Switch 2 ( I)
Switch 3 ( II )
Controls the electricity supply to the heater and
flame effect.
Note: This switch must be in the ON ( I ) position
for heater to operate with or without heat.
Provides 1kW heat output
Provides 2kW output with switch 2
Maintenance
WARNING – BEFORE UNDERTAKING ANY MAINTENANCE OR
CLEANING REMOVE PLUG OR DISCONNECT FROM THE
ELECTRICITY SUPPLY.
4 screws on
back panel
Fig. 4
Two lamps are located behind the back panel as indicated in Fig 4.
To gain access to the lamps, the four screws which secure the
back panel, must be removed. Remove and slide out panel as
indicated on Fig. 5
Fig. 5
Fig. 6
Remove the defective lamp by unscrewing it as shown - see Fig.
6. Replace with a 60W E14 SES Clear Candle lamp.
Take care not to over-tighten the lamp. Refit the back panel and
secure with the four screws.
An automatic cut-out will switch off the heater if for any reason it
overheats. This could occur for instance, if the air inlet or outlet
were restricted in any way. If the cut-out operates, the heater will
switch off. The heater will switch on once the obstruction has
been removed and the heater has cooled. If the cut-out continues
to operate intermittently, the heater should be switched off and
Customer Services contacted.
Safety cut-out