Dini Argeo 3590EKR Series User manual

USER MANUAL
WEIGHT INDICATOR
E-AF08: PROGRAM VERSION FOR
WHEEL AND AXLE WEIGHING
3590EKR, 3590EXP, 3590EXT series indicator
E-AF08_02_13.07_EN_U

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
2
INDEX
1. INTRODUCTION.................................................................................................................................................................4
2. MAIN TECHNICAL SPECIFICATIONS...............................................................................................................................5
2.1 ACCESSORIES AVAILABLE .......................................................................................................................................6
2.2 SYMBOLS USED .........................................................................................................................................................6
3. INSTALLATION ..................................................................................................................................................................7
3.1 CASE AND DIMENSIONS ...........................................................................................................................................7
3.2 POWER SUPPLY & START UP...................................................................................................................................9
3.3 START UP....................................................................................................................................................................9
3.4 TURNING OFF THE INSTRUMENT ..........................................................................................................................10
3.5 TURNING ON PRINTER IN ENERGY SAVING MODE .............................................................................................10
4. FRONT PANEL KEYS AND DISPLAYS...........................................................................................................................10
4.1 FUNCTION OF THE KEYS ........................................................................................................................................10
4.1.1 "2ndF" KEY: SECOND FUNCTION OF THE KEYS.........................................................................................12
4.1.2 ENTERING ALPHANUMERIC TEXT...............................................................................................................12
4.1.3 DISABLING THE KEYBOARD.........................................................................................................................13
4.1.4 HELP MENU....................................................................................................................................................13
4.1.5 INDICATOR CONNECTED TO PC KEYBOARD.............................................................................................14
4.1.6 REMOTE CONTROL.......................................................................................................................................14
4.2 FUNCTION DISPLAY.................................................................................................................................................17
4.2.1 STATUS INDICATORS ...................................................................................................................................17
4.2.2 BATTERY LEVEL INDICATION ......................................................................................................................19
4.2.3 "TILT" DEVICE ................................................................................................................................................19
4.2.4 DISPLAYED DATA..........................................................................................................................................20
4.2.5 CUSTOMIZABLE DISPLAY.............................................................................................................................21
5. SCALES MANAGEMENT.................................................................................................................................................21
5.1 SET THE NUMBER OF ACTIVE SCALES.................................................................................................................21
5.2 SET THE ACTIVE SCALES NUMBER.......................................................................................................................21
5.3 SELECTION OF SINGLE SCALE/SUM FUNCTION..................................................................................................21
5.3 “SUM” FUNCTION .....................................................................................................................................................22
5.5 SUM OF THE SELECTED SCALES ..........................................................................................................................23
6. SCALE ZERO FUNCTIONS..............................................................................................................................................23
6.1 OPERATION OF ZERO ON THE SINGLE SCALE ....................................................................................................23
6.2 CYCLE OF ZERO ON ALL THE CONNECTED SCALES ..........................................................................................23
7. TARE FUNCTIONS...........................................................................................................................................................23
7.1 TARE FUNCTION ON “WHEEL WEIGHING” MODE.................................................................................................23
7.1.1 SEMIAUTOMATIC TARE ................................................................................................................................24
7.1.2 PRESET TARE................................................................................................................................................24
7.2 TARE FUNCTION IN “AXLE WEIGHING” MODE ......................................................................................................24
7.3 MANUAL CALCULATED TARE .................................................................................................................................24
7.4 TARE CANCELLATION .............................................................................................................................................24
7.5 LOCKED/UNLOCKED/DISABLED TARE...................................................................................................................25
7.6 LIMITATION OF THE TARE FUNCTIONS.................................................................................................................25
7.7 TARE EXECUTION MODE OR DISABLING OF THE TARE .....................................................................................25
8. MULTIRANGE AND MULTIDIVISION FUNCTION...........................................................................................................25
9. DISPLAY OF METRIC DATA (inFO)................................................................................................................................25
10. FILLING IN THE INPUT TEXT........................................................................................................................................26
11. DATABASE.....................................................................................................................................................................27
11.1 ENTERING ITEMS...................................................................................................................................................27
11.2 MODIFICATION OF DATA.......................................................................................................................................27
11.3 CANCELLATION OF DATA .....................................................................................................................................28
11.4 PRINTING DATA......................................................................................................................................................28
11.5 DATA SELECTION/DESELECTION ........................................................................................................................28
11.6 ENTRY, MODIFICATION AND QUICK SELECTION OF ITEM 000.........................................................................29

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
3
11.7 ALPHABETICAL RESEARCH..................................................................................................................................29
11.8 HELP........................................................................................................................................................................29
12. DATABASE ACCESS PASSWORD...............................................................................................................................29
13. WEIGHING AND TOTALISATION PROCEDURES........................................................................................................29
13.1 TOTALISATION TYPES...........................................................................................................................................29
13.2 “WHEEL WEIGH” TOTALISATION TYPE................................................................................................................30
13.2.1 UPDATING TOTALS .....................................................................................................................................30
13.2.2 CANCELLING LAST WEIGH.........................................................................................................................30
13.2.3 ENTRY OF COORDINATES FOR CALCULATING THE BARYCENTRE (OR CENTRE OF GRAVITY) ......30
13.3 “AXLE WEIGH” TOTALISATION TYPE....................................................................................................................31
13.3.1 UPDATING TOTALS .....................................................................................................................................32
13.3.2 CANCELLING LAST WEIGH.........................................................................................................................32
13.3.3 ENTRY OF AXLE NUMBER FOR AUTOMATIC PRINTING OF PARTIAL TOTAL .......................................32
13.4 SET TOTALISATION THRESHOLD.........................................................................................................................33
13.5 REENABLING THE PRINTING AND WEIGH ..........................................................................................................33
13.6 VISUALISATION AND CLEARING OF THE ACCUMULATED TOTALS .................................................................33
13.7 PROGRESSIVES.....................................................................................................................................................34
13.7.1 PROGRESSIVE DIGITS................................................................................................................................34
13.7.2 TICKET PROGRESSIVE...............................................................................................................................34
13.7.3 LOT PROGRESSIVE.....................................................................................................................................34
14. PRINTOUTS....................................................................................................................................................................34
14.1 LINKING OF THE FORMATS TO THE PRINT FUNCTIONS...................................................................................36
14.2 NUMBER OF TICKET COPIES................................................................................................................................37
14.3 PRINTING OF THE HEADING.................................................................................................................................37
14.4 REPETITION OF THE LAST EXECUTED PRINTOUT ............................................................................................37
14.5 DEFAULT PRINTING FORMATS.............................................................................................................................37
15. OTHER FUNCTIONS ......................................................................................................................................................38
15.1 CALCULATOR .........................................................................................................................................................38
15.2 DISPLAY OF NET WEIGHT WITH SENSITIVITY X 10 (for testing use during calibration)......................................38
15.3 SETTING DATE / TIME............................................................................................................................................38
15.4 NET  GROSS SWITCH...................................................................................................................................38
15.5 SET-POINT FUNCTION...........................................................................................................................................39
15.5.1 NORMAL FUNCTIONING MODE..................................................................................................................39
15.5.2 EXCLUSIVE FUNCTIONING MODE .............................................................................................................41
15.6 DIAGNOSTIC PERIPHERALS .................................................................................................................................41
15.7 COM DATA DIAGNOSTIC .......................................................................................................................................42
16. ALIBI MEMORY..............................................................................................................................................................42
16.1 READING OF THE WEIGHS CARRIED OUT..........................................................................................................43
16.2 SERIAL COMMANDS FOR MANAGING THE ALIBI MEMORY:..............................................................................43
16.2.1 REQUEST WEIGHT VALUE WITH WEIGH ID..............................................................................................44
16.2.2 STRING FORMAT (WEIGHT/ID)...................................................................................................................44
16.2.3 WEIGH READING .........................................................................................................................................44
16.2.4 ALIBI MEMORY CANCELLATION (only with non approved instrument).......................................................45
17. MESSAGES ....................................................................................................................................................................45
17.1 INSIDE THE SET-UP OR MENU .............................................................................................................................45
17.2 AT START-UP..........................................................................................................................................................46
17.3 IN WEIGHING ..........................................................................................................................................................47
DECLARATION OF CONFORMITY .....................................................................................................................................48
WARRANTY .........................................................................................................................................................................48

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
4
1. INTRODUCTION
This manual was created to help you install and learn all about the functional possibilities of the purchased indicator.
The instrument is suitable for use in various weighing environments.
Not only does it have all the normal features of high-precision scales, but it also gives you the possibility to work in specific
environments due to the functioning modes contained in the software implemented in the FLASH MEMORY on the internal
board; This makes the instrument extremely flexible and it can be used in many different industrial applications linked to
weighing. The double numerical and interactive alphanumerical display, the alphanumerical and function keyboard, allow
the operator an easy and immediate use and provide the microcontroller with DATA ENTRY functions in addition to the
normal weighing functions. The input/output allows the instrument to control various external devices, to receive external
commands, control a printer and communicate with a personal computer or to be inserted in a network of weight indicators
controlled by a PC.
WARNING
With the 6V rechargeable battery option, it has to be completely recharged (12 hours) in the first installation of the
instrument; we RECOMMEND disconnecting the battery if the instrument is not going to be used for more than 30
days. In order to avoid the deterioration of the rechargeable battery:
- In standard conditions never leave the battery partially or completely uncharged; at least once a week recharge it
completely.
- In case the instrument is not used for a long period, one needs to:
1. completely recharge the battery before the system is switched off for the last time.
2. recharge completely every 3 months.
Do not pour liquids on the weight indicator.
Do not use solvents to clean the weight indicator.
Do not expose the instrument to direct sunlight nor place it near heat sources.
Place or anchor the weight indicator and platform on a non-vibrating base.
All the connections of the indicator have to be made respecting
the rules applicable in the zone and in the installing environment.
Everything not expressly described in this manual has to be considered as improper use of the equipment.
Read carefully and apply what is described in section “INSTALLATION”.
Do not install in any area where there is a risk of explosion.
The crossed-out wheeled bin on the product means that at the product end of life, it must be taken to
separate collection or to the reseller when a new equivalent type of equipment is purchased. The
adequate differentiated refuse collection in having the product recycled, helps to avoid possible
negative effects on the environment and health and supports the recycling of the materials of which the
equipment is made. The unlawful disposal of the product by the user will entail fines foreseen by the
current regulations.
Please note that this instrument is covered by a warranty and MUST NOT BE OPENED BY THE USER for
any reason whatsoever. Any attempt to repair or modify the unit exposes the user to the risk of electric shock
and will invalidate the entire warranty.
If any problems are found in the unit or with the system in which it is used, the fact must be communicated to
the manufacturer or the dealer from whom it was purchased.
In any case, DISCONNECT THE POWER SUPPLY before taking any action.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
5
NOTE FOR THE USER
The message (TECH.MAN.REF.), will often appear in this manual; this refers to the Technical Manual, which may obtained
by the reseller.
2. MAIN TECHNICAL SPECIFICATIONS
POWER SUPPLY
- 12 Vdc ( 8 ÷ 24 Vdc in the IO versions), with internal or external 100 ÷ 240 Vac
(50÷60 Hz) / 12 Vdc adapter, depending on the model.
- 6 Vdc from rechargeable built-in battery, fitted depending on the model.
MAXIMUM POWER
16 VA.
OPERATING TEMPERATURE
From -15 to + 40 °C. (5 to 104 °F), with constant temperature.
CONVERTER
24 bit Sigma Delta.
CONVERSION SPEED
up to 200 conv./sec. with automatic selection.
RANGE OF INPUT SIGNAL
0,6 mV/V - 3,2 mV/V.
MINIMUM VOLTAGE PER DIVISION
0.3 V (approved instrument); 0.03 V (non-approved instrument).
TYPICAL INTEGRATION TIME
40 msec.
AUTOMATIC ZERO DETECTION
Only in gross mode, programmable at +/- ¼, ½, 1, 2 divisions.
ZERO RANGE
Configurable up to +/- 50% of max load capacity.
AUTOZERO AT START-UP
Configurable up to +/- 50% of max capacity.
LOAD CELL POWER SUPPLY
5Vdc ± 5%, 120mA (max 8 350-Ohm cells).
LOAD CELL CONNECTIONS
6 wires with Remote Sense.
DISPLAY DIVISIONS
10000e, 3 x 3000e for legal weighing, expandable up to 800.000 for internal use
(with minimum signal coming from a 1,6mV/V cell).
DISPLAYS
- Red, high-luminosity LED indicators, with six digits (h 13 mm)
- Back lit graphic 160x32 dot LCD
TARE FUNCTION
Subtractive, possible on all capacities.
MEMORY/DATABASE
Database of 1000 items (each with 5 descriptions of 20 characters).
SIGNALS
16 status LEDs. Graphic icons on LCD display.
KEYBOARD
Impermeable polycarbonate keyboard with 24 multifunction (IP65 protection
degree), with membrane keys with audible and tactile feedback.
PARAMETER SETUP
Calibration and linearity (up to 8 points), fully digital and programmable from the
keyboard.
CLOCK/DATE
Standard feature, with buffer RAM.
PROTECTIVE CASE
ABS console (IP 65 protection).
SERIAL OUTPUTS
- 2 input/output RS232 ports on terminal board/ amp connector.
- 1 input/output RS485 port on terminal board or RS232 on amp connector.
INPUTS AND OUTPUTS
- Management of PC keyboard or barcode reader
3590EKR, 3590EXP and 3590EXT:
- 2 inputs (optoisolated photo couplers), 12Vdc –24Vdc, 20mA max
- 4 outputs (optoisolated photomosfets), 48Vac / 0.15A, 60Vdc / 0.15A, 10 Ω max.
3590EXT in IO version:
- 8 inputs (optoisolated photo couplers), 12Vdc –24Vdc, 20mA max.
- 16 outputs (optoisolated photomosfets), 48Vac / 0.15A, 60Vdc / 0.15A.
ANALOGUE OUTPUT (Option
available on the 3590EXT “IO”
version)
- 16-bit analogue output configurable from keyboard (full-scale value; zero scale
value and minimum value) from 0 to 10 Vdc or from 0 to 20mA; the maximum
resistance applicable on the output current is 350 Ohm and the minimum
resistance applicable on the output voltage is 10 kohm.
THE INSTRUMENT’S DANGEROUS VOLTAGE PARTS AND THE PARTS THE USER CAN ACCESS HAVE BEEN
ELECTRICALLY INSULATED.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
6
2.1 ACCESSORIES AVAILABLE
On the indicator it is possible to implement internal and external modules used to increase interfacing possibilities.(For
example, the number of usable outputs various types of printers, in order to have a report of the weighs made, or a giant
display in order to better see the weigh operations. Also, one can connect a PC in order to simply program the instrument
through Dinitools™, or in order to have a complete management of the weighs.
Contact the reseller for the list of the available hardware and software accessories.
2.2 SYMBOLS USED
Below are the symbols or texts used in the manual to recall the reader’s attention and on the instrument to recall
the user’s attention
ATTENTION!
Only qualified personnel must perform this operation
ATTENTION!
This is referred to working on energized lines: only qualified personnel must require or perform
this operation.
CE CONFORMITY
IDENTIFIES THE CLASS OF PRECISION.
“TECH.MAN.REF.”
It means that an advanced function is being described (therefore for the technical personnel)
which will be further explained in the corresponding technical manual.
THE INSTRUMENT’S DANGEROUS VOLTAGE PARTS AND THE PARTS THE USER CAN ACCESS HAVE BEEN
ELECTRICALLY INSULATED.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
7
3. INSTALLATION
3.1 CASE AND DIMENSIONS
ABS MODEL
The indicator has an IP65 ABS case, whose external dimensions are shown in the Figure. It can be simply put on a table or
fixed to a shelf or column available on request.
NOTE: If the identification plate is supplied separately (therefore not attached to the indicator), it is advisable to
attach it to the indicator, in order to be able to identify the instrument.
Figure 2 –Measurements and dimensions in mm
1) RJ45 connector
2) Fixing for shelf or column mounting
3/5) Available for load cells / serial lines / inputs / outputs.
4) Power supply input.
1
2
3
4
5

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
8
Figure 3 –Measurements and dimensions in mm
1) RJ45 connector
2) Fixing for shelf or column mounting
3) Available for load cells / serial lines / inputs / outputs.
4) Power supply input.
STAINLESS STEEL MODEL
The indicator has an STAINLESS STEEL case, whose external dimensions are shown in the Figure 3. It can be simply put
on a table or fixed to a shelf or column available on request.
NOTE: If the identification plate is supplied separately (therefore not attached to the indicator), it is advisable to
attach it to the indicator, in order to be able to identify the instrument.
1
2
3
4
3

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
9
3.2 POWER SUPPLY & START UP
- The 3590EXP and 3590EXT indicator is powered with 12Vdc voltage (8 ÷ 24 Vdc in the IO version), through an internal
adapter which converts the 100 ÷240Vac, 50÷60Hz mains voltage, and 6 Vdc, from the battery (fitted depending on the
model).
- The 3590EKR indicator is powered with 12Vdc voltage through an external adapter which converts the 100 ÷240Vac,
50÷60Hz mains voltage, and 6 Vdc, from the battery.
TO POWER the instrument through the 240 Vac mains, or TO RECHARGE the battery, insert the plug and the adapter to
the 240 Vac mains socket..
To connect it to the power mains, the safety regulations must be observed, including the use of a "clean" line without
disturbances or interference caused by other electronic equipment.
Version with rechargeable battery: The battery inside the indicator lasts about 25 hours (without the expansion board,
with 1-cell platform) and it needs a recharging time of about 12 hours.
BATTERY FEATURES
Material LEAD
Power 4,5 Ah
Voltage 6 V
THE BATTERY MUST BE SUPPLIED DIRECTLY FROM THE MANUFACTURER.
NOTE: it is advisable to completely recharge it (12 hours) in the first installation of the instrument; we
RECOMMEND disconnecting the battery if the instrument is not going to be used for more than 30 days.
Do not connect other equipment to the same socket as the one that the adapter is in.
Do not step on or crush the power supply cable
3.3 START UP
TO TURN ON the instrument press the C key until the 6 status indicator LEDS turn on; then release.
The LCD display shows:
-Initially a welcome message (settable in the TECHNICAL SET-UP, << LoGo >> step, TECH.MAN.REF.)while the
instrument carries out a series of checking and preheating self tests.
-E-AF08 - XX” name of the installed software, in which XX identifies the software language.
-XX.YY is the software version installed.
-“EXECUTION AUTOZERO” the instrument carries out the "autozero at start-up” function on all active scales:
if a weight is detected within the percentile set in the << Auto 0 >> step (TECH.MAN.REF.), it is cleared; if the weight is not
within this tolerance:
-with a non approved instrument, the display shows the weight after a few instants,
-with an approved instrument “ZErO X” is shown continuously on the LED display, (in wich X show the number of
scale where zero function is done) until the weight does not re-enter within this tolerance.
The auto zero function at start-up may be disabled in the set-up environment (only with non approved instrument); see
SEtuP >> ConFiG >> PArAM. >> Auto 0 (TECH.MAN.REF.).
By pressing the 2ndF key for an instant while the version is shown in the display, the indicator will shown in this order:
XX.YY in which XX indicates the instrument type, YY indicates the metrological software version.
XX.YY.ZZ is the installed software version.
HH is the installed hardware version (08).
LEGAL FOR TRADE or
HIGH RESOLUTION if the instrument is APPROVED or UNAPPROVED, respectively.
9.XXXXX is the the g gravity value (only with APPROVED instrument).

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
10
3.4 TURNING OFF THE INSTRUMENT
TO TURN OFF the instrument keep the C key pressed until the “- OFF -“ message appears on the LED display and “ ***
POWER OFF *** ” on the LCD display.
3.5 TURNING ON PRINTER IN ENERGY SAVING MODE
Premise: the SEtuP >> SEriAL >> CoMPrn >> PWrPrn parameter must be set as “EXtoFF” or “PWrint”
(TECH.MAN.REF.).
In a system where the indicator is connected to a printer, both are battery powered, the printer is normally maintained in
STAND-BY and powered only when a printout is needed. This function reduces the energy absorbed by the battery when
the printer is not being used.
If, in this configuration, one should power the printer to change the paper and other maintenance jobs, one needs to press
the ENTER and 0 keys one after the other, during the weighing: the LED display shows “Prn –on”, and the printer is kept
on. Press any key to exit from this condition.
4. FRONT PANEL KEYS AND DISPLAYS
4.1 FUNCTION OF THE KEYS
In the following section, and later on in the manual, the keys’ functioning is described in accordance to how these are
configured by factory.
It is possible to customise the functionality of the keys through the << F.KEYS >> step.
C/DEL
- Turns the instrument on/off.
- If pressed for an instant, it clears the tare value.
- Exits the parameter without confirming and saving the modifications.
- In the numeric input phase, it quickly clears the present value.
TARE/ZERO
- If pressed for an instant it carries out the tare function.
See section “TARE FUNCTIONS”, for the specific tare function, depending on the selected
totalisation type (wheel weighing/axle weighing).
-If pressed at length, when viewing one scale, it clears the relative gross weight, if it’s within the
percentage configured in the << 0.PErC >> step.
Fn/ENTER
- In the alphanumeric input phase, it confirms the entry made.
- In the menu it allows to enter a step or to confirm a parameter inside a step.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
11
2nd F
-If pressed together with the other keys, it allows carrying out a specific function. (see section “"2ndF"
KEY: SECOND FUNCTION OF THE KEYS”).
-In the << F.Keys >> step, if pressed for an instant, the list of the available functions appear and it is
possible to choose one of them.
./HELP
-If pressed in some steps or functions of the weight indicator, the display shows the keys and their
functions specific to that state of the instrument.
-In the numeric or alphanumeric input phase, it enters, in this order, the following characters: . , ; : # <
> \ | ” % & / ( ) = ? ^ ’ [ ] { };
-HELP function, see section “HELP MENU”.
F1
-By entering a number through numerical keyboard and then pressing the F1 key, one can quickly
select the database item corresponding to the entered value (the article must have already been
edited).
- In the numeric or alphanumeric input phase, it allows to copy entered characters.
-If pressed for an instant it allows entering the database.
-If pressed at length one locks and unlocks the instrument’s keyboard (except the Ckey)
F2
- In the numeric or alphanumeric input phase, it allows to stick with copied characters.
-If pressed for an instant it allows to insert the coordinates of the active scale.
-If pressed at length the weight visualization function with sensitivity x 10 is enabled.
F3
-If pressed for an instant it allows to insert the number of weighs after which it will be printed and the
partial total is cleared. If the value to be inserted is equal to 0, the automatic printing is disabled.
-If pressed at length one can adjust the date and time of the instrument.
F4
-If pressed for an instant it allows filling in the free texts, if configured.
-If pressed at length one enters the instrument’s diagnostics menu.
F5
-Commands the data transmission to the printer serial port.
-If pressed at length one locks/unlocks the tare.
F6
-If pressed for an instant it allows to totalize the weight on the weighing system.
-Allow to scroll forwards in the menu steps or in the parameters inside a step.
-In the numeric or alphanumeric input phase, it decrements the blinking digit.
F7
- If pressed for an instant, it allows to enter the combination of scales, for which one wants to display
the sum (see section ”SUM OF THE SELECTED SCALES”).
-Allow to scroll backwards in the menu steps or in the parameters inside a step.
-In the numeric or alphanumeric input phase, it increments the blinking digit.
F8
-If pressed for an instant it allows printing and resetting the partial total.
-In the numeric or alphanumeric input phase, it selects the digit to be modified from right to left.
F9
-If pressed for an instant it allows printing and resetting the general total.
-In the numeric or alphanumeric input phase, it selects the digit to be modified from left to right.
F10
-If pressed for an instant, it executes the printing and the zeroing of the grand total.
- In the numeric or alphanumeric input phase, introduces a space between two characters.
NUMERIC
KEYBOARD
-Entry of digits or characters.
-During the weighing, these enter a numeric value with which it’s possible to:
1) Set the tare value, by pressing then the TARE key (see section “TARE FUNCTIONS”).
2) To add or to subtract to the current tare the result of the operation between two values enterable
with the keyboard (See the “CALCULATOR”section).

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
12
4.1.1 "2ndF" KEY: SECOND FUNCTION OF THE KEYS
In the weighing phase, by pressing the 2ndF key together with another key, it’s possible to execute various functions
(continue reading the manual for the details of the functions):
2ndF
F2
Allows to select the number of active scales.
2ndF
F3
Allows to select the type of totalisation (wheel weighing/axle weighing, see
section “WEIGHING AND TOTALISATION PROCEDURES”).
2ndF
F5
Repetition of the last printout made.
2ndF
F6
Prints sample list.
2ndF
F7
Clears last sample (see section “CANCELLING LAST WEIGH” in the chapter
“”WHEEL WEIGH” TOTALISATION TYPE” or “”AXLE WEIGH”
TOTALISATION TYPE”.
2ndF
F8
Net/Gross weight conversion on LED display (see section “NET 
GROSS SWITCH”).
2ndF
F9
Modification of what is viewed on the LCD display (see section “DISPLAYED
DATA”).
2ndF
F10
Sets the higher totalisation threshold.
2ndF
C
Causes display of metric information of the current scale (see section
“DISPLAY OF METRIC DATA (inFO)”).
2ndF
TARE/ZERO
Cyclical scale zero on the active scales (see section “CYCLE OF ZERO ON
ALL THE CONNECTED SCALES”).
2ndF
0
Allows switching the visualization on the sum weight of active scales
2ndF
1
Allows switching the visualization on the weight of scale 1.
2ndF
2
Allows switching the visualization on the weight of scale 2.
2ndF
3
Allows switching the visualization on the weight of scale 3.
2ndF
4
Allows switching the visualization on the weight of scale 4.
2ndF
5
Allows switching the visualization on the weight of scale 5.
2ndF
6
Allows switching the visualization on the weight of scale 6.
2ndF
7
Allows switching the visualization on the weight of scale 7.
2ndF
8
Allows switching the visualization on the weight of scale 8.
4.1.2 ENTERING ALPHANUMERIC TEXT
It might be necessary, while the weighing system is working, to enter some alphanumerical texts such as descriptions,
alphanumerical messages (operator, number of lot, customer, etc.).
To enter the characters one uses the 0 to 9 keys.
By pressing one of these keys a few times, the characters shown on the key (and other special characters) will be shown
on the LCD display: initially the first letter in the bottom left will appear, and then the other characters towards the right.
After digiting a character, the blinking cursor, after a few instants, advances automatically of a position. When the maximum
number of characters has been reached, the indicator emits an acoustic signal and the cursor remains in that positions.
In the updating of a text, if the cursor is at the beginning of the text and the first key pressed is C or a character/number key,
all the entered characters will be deleted.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
13
Function of the keys
F5
Switches the writing mode from “numeric” (nuM) to “characters” (ChAr).
In the nuM mode one enters just the numbers, while in the ChAr mode one can enter all the characters of
a key. The last writing mode selected is stored by the instrument.
C
If pressed for an instant, it cancels the written characters: first the characters that follow the cursor are
cancelled; than those that precede it, one at a time.
If pressed at length, it deletes all entered characters.
With empty text, it exits the entry phase without confirming.
SHIFT
It enters a space in the middle of a text.
./HELP
If pressed a few times it allows entering the following characters: . , ; : # < > \ | ” % & / ( ) = ? ^ ’ [ ] { }.
0
In “characters” mode (ChAr),by pressing once a space is entered; by pressing twice it enters the “0”
character.
1
In “characters” mode (ChAr), pressed repeatedly, it allows to enter the following symbols:
? ! 1 @ ’ + – * / = ~ € „ … † ‡ ˆ ‰ š < OE ž ı ’ “ ” • – –˜ ™ Š > oe ž ¢ £ ¤ ¥ ¦ § ¨ © ª « ¬ - ® ¯ ° ± ² ³ ´ μ ¶ · ¸
¹ º » ¼ ½ ¾ ¿ ã.

Moves the blinking cursor to the left or to the right.

Scrolls in one sense or the other the list of all the enterable characters (0, 1…9, A, B…Y, Z).
Examples:
-To enter the letter “B” one should press the “2” key twice in the ChAr mode.
-To enter the number “3” one should press the “3” key four times (in the ChAr mode) or press the F5 key (one passes to
the nuM mode) and press the “3” key once.
4.1.3 DISABLING THE KEYBOARD
It is possible to disable all the keyboard functions (except the Ckey for turning on and off), in order to avoid undesired
pressings of the scale keys:
-To lock the keyboard, press at length the F1 key: the display shows the “LoCK” message for a few instants. Now the
keyboard is LOCKED: if one presses a key, the display shows for a few instants the “PRESS AT LENGTH F1 FOR
UNLOCKING” message.
-To unlock the keyboard, press again at length, the F1 key: the display shows the “unLoCk” message for a few
instants.
NOTE: It’s possible to lock all keys individually in a permanent way through the TECHNICAL SET-UP, TECH.MAN.REF..
4.1.4 HELP MENU
By pressing at length the HELP key it is possible to access a menu containing the list of keys with the relative function, and
status (locked or unlocked) indication.
The display shows:
- in the upper part: the key, followed by the code of the linked function in the << F.KEYS >> step, and a symbol
indicating whether the key is unlocked ( ) or locked ( ) in the << En.KEYS >> step.
- in the lower part: the description of the linked function.
Scroll the list with the arrow keys , press the Ckey to exit.
F1:310  C
ITEM DATABASE

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
14
4.1.5 INDICATOR CONNECTED TO PC KEYBOARD
It’s possible to connect a PC keyboard (optional), used to emulate the functions of the keys of the indicator.
The keys are managed in the following way:
KEYBOARD
KEY OR FUNCTION EMULATED
Esc
-C key.
- If pressed at start-up, it allows entering in the technical set-up.
In the alphanumeric input, it deletes all entered characters.
and Canc
-C key.
- If pressed at start-up, it allows entering in the technical set-up.
In the alphanumeric input, it cancels first the characters which follow the cursor, then the ones which
precede it, one at a time.
Enter

-Fn key.
- Confirms the entered value.
- Enters the displayed step.
Numeric and
alphanumeric
keys, SHIFT and
CAPS LOCK
- Quick entry of a numeric and alphanumeric string: through the CAPS/LOCK or SHIFT key it is possible
to switch from the capital letters to the lower case letters, and vice versa, or enter the second character
corresponding to the key (for example ", %, &, /, ? ). The entered string is shown on the LCD display.
Cursor keys

- Scroll the parameters.
- Increase or decrease the blinking digit while entering a value.
Cursor keys

- When entering a value or an alphanumeric string, it scrolls the digits to the right or to the left.
F1, F2….F10
F1,F2….F10 keys.
F11
2ndF key.
F12
TARE key.
The PC keyboard also allows to enter a numeric or alphanumeric string (max.32 characters) and then press a key to
execute the corresponding quick function.
For example, if the function 122 (input text 1 configuration) is combined to the F4 key (see << F.KEYS >> step,
TECH.MAN.REF.), through PC keyboard it’s possible to enter a text and the press F4 to quickly modify the input text 1.
NOTE: through the remote keyboard, it’s not possible to carry out the functions made by pressing the keys at length.
4.1.6 REMOTE CONTROL
Depending on the model of indicator, it is possible to remotely control the instrument through one of the following types of
remote controls: 19-key infrared (ir), 18-key infrared (ir) or 6-key radio (rd).
The type of remote control to be used must be selected in the Setup environment, in the << inF.rEd >> step
(TECH.MAN.REF.).
NOTE: The infrared remote controls are for indoor use only.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
15
ir.2nd F
●2nd F
○Tare
4.1.6.1 “19-KEY” INFRARED REMOTE CONTROL
With this type of remote control, the functioning of the keys will be as described in the following table.
FUNCTION OF THE KEYS
4.1.6.2 “18-KEY” INFRARED REMOTE CONTROL
With this type of remote control, the functioning of the keys will be as described in the following table.
The remote control can be programmed so that it will emulate the Tare key instead of the 2nd F key of the indicator and the
function keys from F1 to F10 instead of the numeric keys (numeric key 1 for F1, numeric key 2 for key F2 etc…); see below
the configuration details.
FUNCTION OF THE KEYS
CONFIGURATION
To execute this configuration:
- press at length the Fn key on the remote control;
- the configuration of the 2nd F key is proposed:
KEYBOARD
KEY OR FUNCTION EMULATED
Fn
Fn key
2nd F
2nd F key or Tare function (see configuration below)
C
C key
NUMERIC KEYS
Entry of digits or emulation of F1...F10 keys (see
configuration below)
TARE / 
Tare function or increase of a digit while entering a value
.
./HELP key
ZERO / 
Zero function or decrease of a digit while entering a value
MODE / 
Scrolls the digits to the right while entering a value
PRINT / 
Confirms the entered value or enters the displayed step
KEYBOARD
KEY OR FUNCTION EMULATED
F1…F3
F1…F3 keys
C
C key
NUMERIC KEYS
Entry of digits
TARE / 
Tare/zero function or increase of a digit while entering a
value
.
./HELP key
ZERO / 
Decrease of a digit while entering a value
MODE / 
Scrolls the digits to the right while entering a value
PRINT / 
Confirms the entered value or enters the displayed step

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
16
ir.numb
●numeric keys
○function keys
- select the desired key that should be simulated by using the arrow keys and press the PRINT /key to confirm
and pass to the following setting;
- the configuration of the numeric key is proposed:
- select the desired functioning of the numeric key (simulating the numbers or simulating the function keys from F1…F10)
by using the arrow keysand press the PRINT / key to confirm and exit the menu.
4.1.6.3 “6-KEY” RADIO REMOTE CONTROL
With this type of remote control, the functioning of each key can be programmed so that it is matched to one of the available
keys of the indicator.
This configuration must be carried out in the Setup environment, in the << inF.rEd >> step (TECH.MAN.REF.), after the
selection of this type of remote control.
By pressing the ./HELP key of the indicator, it’s possible to see, while weighing, the list of the functions matched to the keys
of the indicator and also to the keys of the remote control (see section “HELP MENU”).
EXAMPLE OF CONFIGURATION
USE OF MORE REMOTE CONTROLS WITH ONLY ONE INDICATOR
If one works with only an indicator, it is possible to use any 6-key remote control, without combining it to the indicator,
therefore without limiting the number of usable remote controls.
To enable this mode one has to first select “RD 6 BR” in the << inF.rEd >> (TECH.MAN.REF.).
USE OF MORE REMOTE CONTROLS WITH SEVERAL INDICATORS IN THE SAME AREA
If one needs to use several indicators in the same area, it is possible to combine each remote control to the desired
indicator, in order to execute the function only on it and therefore avoid emulating the function on all indicators in use.
By enabling this mode it will be possible to combine up to 3 different remote controls (e.i. for 3 different operators) for each
indicator.
To enable this mode one has to first select “RD 6” in the << inF.rEd >> (TECH.MAN.REF.).
To link a new remote control to the indicator one has to:
- press at length 1 and 2 keys together (3 seconds).
- the instrument displays "aut.rd?"
- press the ENTER key of the indicator
- the new remote control is linked
To remove the linking of a remote control one has to:
- press at length 1 and 2 keys together (3 seconds).
- the instrument displays "aut.rd?"
- press the C key of the indicator; if the remote control was previously linked, it will be removed.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
17
4.2 FUNCTION DISPLAY
During the weighing the displays are subdivided mainly in 3 sections, shown in the figure below:
1) SUM WEIGHT / SELECTED SCALE WEIGHT (see section “SCALE MANAGEMENT”)
2) STATUS INDICATORS (led pilot lights and graphic symbols)
3) SCALES’ DATES / WEIGHT (see section “DISPLAYED DATA”)
2 3 2
1
2
4.2.1 STATUS INDICATORS
LED
FUNCTION
POWER
Indicates the type of indicator power supply:
-red pilot light: through built-in power adapter;
-green pilot light: through battery (charged battery);
-pilot light off: through battery (discharged battery).
0
Indicates that the weight detected by the weighing system is near zero, including the interval of 1/4 +1/4
of the scale’s division.
~
I Indicates that the weight is unstable.
NET
Indicates that the weight shown by the LED display is a NET WEIGHT.
T
Indicates that a tare value has been acquired or entered.
g
Indicates that the unit of measure in use is the gram.
kg
Indicates that the unit of measure in use is the kilogram.
t
Indicates that the unit of measure in use is the ton.
PCS
Not used in the application.
F
Not used in the application.
START
Not used in the application.
STOP
Not used in the application.
W1 W2 W3
See section “MULTIRANGE AND MULTIDIVISION FUNCTION”.
SP1
Not used in the application
SP2
Not used in the application
S1: 1000 S2: 1000
S3: 1000 S4: 1000

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
18
SYMBOLS’ FUNCTIONS ON THE LCD DISPLAY
SYMBOL
FUNCTION
,
Indicates the type of active totalisation (see section “WEIGHING AND TOTALISATION
PROCEDURES”).
The weight detected by the weighing system is near the zero, included within the interval of
–1/4 and +1/4 of the scale division. Icon viewable only when the DIAGNOSTICS
PERIPHERAL UNITS function is active, see section “DIAGNOSTIC PERIPHERALS”.
The weight is unstable. Icon viewable only when the DIAGNOSTICS PERIPHERAL UNITS
function is active, see section “DIAGNOSTIC PERIPHERALS”.
Unit of measure in use: ton, kilogram, gram, pounds.
Active scale (see section “SCALES MANAGEMENT”). Icon viewable only when the
DIAGNOSTICS PERIPHERAL UNITS function is active, see section “DIAGNOSTIC
PERIPHERALS”.
Respectively indicates the status of an output as non active or active. Icon viewable only
when the DIAGNOSTICS PERIPHERAL UNITS function is active, see section
“DIAGNOSTIC PERIPHERALS”.
Respectively indicates the status of an input as non active or active . Icon viewable only
when the DIAGNOSTICS PERIPHERAL UNITS function is active, see section
“DIAGNOSTIC PERIPHERALS”.
Serial communication with external device. Icon viewable only when the DIAGNOSTICS
PERIPHERAL UNITS function is active, see section “DIAGNOSTIC PERIPHERALS”.
Battery charge level: see section “BATTERY LEVEL INDICATION”.
Active during the configuration of the date and time.
Locked keyboard, see section “DISABLING THE KEYBOARD”.
In the HELP menu these respectively indicate whether a key is unlocked or locked in the
SETUP level (<< En.KEYS >> step, see section “HELP MENU”.
The Fn key has been pressed.
The 2nd Fkey has been pressed.
Transmission of the data to the printer serial port under way.
Inside the step, these respectively indicate an unselected or selected parameter.
Active calculator function, see section “CALCULATOR”.
5
6
7
8

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
19
4.2.2 BATTERY LEVEL INDICATION
The indicator is able to recognise whether it is powered by mains or by battery, and indicate its charge level; to enable the
battery level indication, one should configure the << bt.StAt >> step (TECH.MAN.REF.).
The charge level is shown during weighing by the battery symbol.
- : charged battery.
- : partially charged battery.
- : discharged battery: connect the indicator to the mains for recharging the battery (if provided for by that model) or
replacing the battery.
The indicator shows also when the battery is being recharged (if provided for the model):
RECHARGE PHASE: …
COMPLETED RECHARGE:
NOTES:
- During the recharge the instrument can be normally used.
- The instrument automatically turns off when the voltage goes below the minimum level.
4.2.3 "TILT" DEVICE
The TILT is a device which inhibits the indicator’s weighing system and starts working when the instrument’s inclination is
greater than 2% for the pallet truck application or 5% for application on lift trucks.
The “tilt” message is shown on the display, alternate to the weight value.
The activation of the tilt alarm has a delay of about three seconds from the detection of the exceeding inclination.
See the electrical connection scheme (TECH.MAN.REF.) for the connection of the device.

3590EKR, 3590EXP, 3590EXT series indicator E-AF08_02_13.07_EN_U
20
4.2.4 DISPLAYED DATA
The data is displayed on up to three lines; their visualisation depends on the weighing type and the number of active scales.
By pressing in sequence the 2nd F and F9 keys, one will scroll through the following visualisations in this order:
NUM
VISUALIZATION
WHEEL WEIGHING
AXLE WEIGHING
0
-Active scales
-Active tare (PT)
1
-Active scales
-First description data selected
2
-Active scales
-Sum weight of the scale
combination (see section
“SUM OF THE SELECTED
SCALES”)
3
In the wheel weighing mode:
- Active scales and Barycentre
Coordinates
In the axle weighing mode:
-Active scales and number of
weighed axles, and accumulated
total gross weight (when one is
finished with the vehicle, the tare
is subtracted from the total, if it is
present)
4
-Active scales
-Number of vehicles weighed
and the total net weight
accumulated
By linking the function to a direct key, see the << F.KEYS >> step, it is possible to quickly recall a visualisation by digiting,
with the numeric keyboard, the relative number and pressing the key linked to the function.
Notes:
- Default visualisation: 0.
S1: 1000 S2: 1000
S3: 1000 S4: 1000
S1: 1000 S2: 1000
S1: 1000 S2: 1000
S3: 1000 S4: 1000
S1: 1000 S2: 1000
S1: 1000 S2: 1000
S3: 1000 S4: 1000
S1: 1000 S2: 1000
S1: 1000 S2: 1000
S3: 1000 S4: 1000
S1: 1000 S2: 1000
S1: 1000 S2: 1000
S3: 1000 S4: 1000
S1: 1000 S2: 1000
PT: 500Kg
PT: 500Kg
ARTICLE 1
ARTICLE 1
12= 2000Kg
12= 2000Kg
X= 6.50 m Y= 7.50 m
AX.T. 00001- 2000Kg
V.TOT. 00001-4000Kg
V.TOT. 00001- 4000Kg
Σ
Σ