Dini Argeo 3590EXT Series User manual

USER MANUAL
WEIGHT INDICATOR
E-AF09: PROGRAM VERSION FOR DYNAMIC OR STATIC
AXLES WEIGHING WITH INPUT/OUTPUT FUNCTION
3590EKR, 3590EXP, 3590EXT, CPWE, CPWET erie indicator
E-AF09_02_13.01_EN_U

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
1
INDEX
1. INTRODUCTION ................................................................................................................................................................... 4
2. MAIN TECHNICAL SPECIFICATIONS ................................................................................................................................. 5
2.1 ACCESSORIES AVAILABLE ......................................................................................................................................... 6
2.2 SYMBOLS USED ........................................................................................................................................................... 6
3. INSTALLATION .................................................................................................................................................................... 7
3.1 CPWE DRILLI G TEMPLATE, CASE A D DIME SIO S ........................................................................................... 7
3.2 3590E CASE A D DIME SIO S .................................................................................................................................. 8
3.2.1 ABS MODEL ........................................................................................................................................................ 8
3.2.2 STAI LESS STEEL MODEL ............................................................................................................................... 9
3.3 CPWET CASE A D DIME SIO S.............................................................................................................................. 10
3.4 POWER SUPPLY ......................................................................................................................................................... 11
3.5 START UP .................................................................................................................................................................... 11
3.6 TUR I G OFF THE I STRUME T ............................................................................................................................ 11
3.7 TUR I G O PRI TER I E ERGY SAVI G MODE ............................................................................................... 12
4. FRONT PANEL KEYS ........................................................................................................................................................ 12
4.1 FU CTIO OF THE KEYS .......................................................................................................................................... 13
4.2 "2ndF" KEY: SECO D FU CTIO OF THE KEYS ..................................................................................................... 15
4.3 E TERI G ALPHA UMERIC TEXT ........................................................................................................................... 15
4.4 DISABLI G THE KEYBOARD ..................................................................................................................................... 16
4.5 HELP ME U ................................................................................................................................................................ 16
4.6 I DICATOR CO ECTED TO REMOTE KEYBOARD ............................................................................................... 16
4.7 REMOTE CO TROL.................................................................................................................................................... 17
4.7.1 “19-KEY” I FRARED REMOTE CO TROL ...................................................................................................... 17
4.7.2 “6-KEY” RADIO REMOTE CO TROL ............................................................................................................... 18
5. DISPLAY FUNCTIONS ....................................................................................................................................................... 19
5.1 WEIGHT ZOOM (available only on CPWE and CPWET models) ................................................................................ 20
5.2 STATUS I DICATORS ................................................................................................................................................ 20
5.3 BATTERY LEVEL I DICATIO ................................................................................................................................... 21
5.4 DISPLAYED DATA ....................................................................................................................................................... 22
5.4.1 LCD DISPLAY CUSTOMIZATIO (O LY FOR 3590E I DICATORS) ............................................................. 23
5.5 MESSAGES OF THE I STRUME T ........................................................................................................................... 24
5.5.1 I SIDE THE SET-UP OR ME U OR AT START-UP ........................................................................................ 24
5.5.2 I WEIGHI G.................................................................................................................................................... 25
6. SCALE ZERO FUNCTION .................................................................................................................................................. 25
7. TARE FUNCTIONS ............................................................................................................................................................. 25
7.1 MA UAL PRESET TARE TO BE SUBTRACTED TO THE TOTAL ACCUMULATED WEIGHT .................................. 25
7.2 CALCULATED MA UAL TARE ................................................................................................................................... 26
7.3 TARE CA CELLATIO ............................................................................................................................................... 26
7.4 LOCKED/U LOCKED TARE ....................................................................................................................................... 26
7.5 LIMITATIO OF THE TARE FU CTIO S ................................................................................................................... 26
7.6 TARE EXECUTIO MODE OR DISABLI G OF THE TARE ....................................................................................... 26
7.7 E TERI G OF A PRESET TARE I A VEHICLE I THE DATABASE. ...................................................................... 26
8. MULTIRANGE AND MULTIDIVISION FUNCTION ............................................................................................................. 27
9. DISPLAY OF METRIC DATA (inFO) .................................................................................................................................. 27
10. FILLING IN THE INPUT TEXT .......................................................................................................................................... 27
11. DATABASE....................................................................................................................................................................... 28
11.1 CUSTOMER DATABASE ........................................................................................................................................... 28
11.1.1 E TRY ............................................................................................................................................................ 28

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
2
11.1.2 MODIFICATIO ............................................................................................................................................... 29
11.1.3 CA CELLATIO ............................................................................................................................................. 29
11.1.4 PRI TI G ....................................................................................................................................................... 29
11.1.5 SELECTIO / DESELECTIO ........................................................................................................................ 30
11.1.6 E TRY, MODIFICATIO A D QUICK SELECTIO OF CUSTOMER 000 .................................................... 31
11.1.7 ALPHABETICAL RESEARCH ......................................................................................................................... 31
11.1.8 HELP ............................................................................................................................................................... 31
11.2 MATERIALS ............................................................................................................................................................... 31
11.2.1 E TRY ............................................................................................................................................................ 31
11.2.2 MODIFICATIO ............................................................................................................................................... 32
11.2.3 CA CELLATIO ............................................................................................................................................. 32
11.2.4 PRI TI G ....................................................................................................................................................... 32
11.2.5 SELECTIO / DESELECTIO ........................................................................................................................ 33
11.2.6 E TRY, MODIFICATIO A D QUICK SELECTIO OF MATERIAL 000 ....................................................... 33
11.2.7 ALPHABETICAL RESEARCH ......................................................................................................................... 34
11.2.8 HELP ............................................................................................................................................................... 34
11.3 VEHICLES .................................................................................................................................................................. 34
11.3.1 E TRY ............................................................................................................................................................ 34
11.3.2 MODIFICATIO ............................................................................................................................................... 35
11.3.3 CA CELLATIO ............................................................................................................................................. 35
11.3.4 PRI TI G ....................................................................................................................................................... 35
11.3.5 SELECTIO / DESELECTIO ........................................................................................................................ 36
11.3.6 E TRY, MODIFICATIO A D QUICK SELECTIO OF VEIHCLE 000 ......................................................... 36
11.3.7 ALPHABETICAL RESEARCH ......................................................................................................................... 37
11.3.8 HELP ............................................................................................................................................................... 37
12. DATABASE ACCESS PASSWORD ................................................................................................................................. 37
13. WEIGHING PROCEDURES .............................................................................................................................................. 37
13.1 GE ERAL DESCRIPTIO OF THE SYSTEM ........................................................................................................... 37
13.2 SIMPLE AXLES WEIGHI G ...................................................................................................................................... 38
13.2.1 MA UAL AXLE WEIGHI G ............................................................................................................................ 38
13.2.1.1 CO FIGURATIO ............................................................................................................................. 38
13.2.1.2 WEIGHI G PROCEDURE ................................................................................................................. 38
13.2.2 AUTOMATIC STATIC AXLE WEIGHI G ........................................................................................................ 40
13.2.2.1 CO FIGURATIO ............................................................................................................................. 40
13.2.2.2 WEIGHI G PROCEDURE ................................................................................................................. 40
13.2.3 AUTOMATIC DY AMIC AXLE WEIGHI G ..................................................................................................... 43
13.2.3.1 CO FIGURATIO ............................................................................................................................. 43
13.2.3.2 WEIGHI G PROCEDURE ................................................................................................................. 43
13.3 I PUT-OUTPUT AXLE WEIGHI G ........................................................................................................................... 46
13.3.1 MA UAL AXLE WEIGHI G ............................................................................................................................ 46
13.3.1.1 CO FIGURATIO ............................................................................................................................. 46
13.3.1.2 I PUT WEIGHI G PROCEDURE ..................................................................................................... 46
13.3.1.3 STARTI G OUTPUT WEIGHI G THROUGH ID CODE ................................................................... 48
13.3.1.4 STARTI G OUTPUT WEIGHI G THROUGH LICE SE PLATE ....................................................... 49
13.3.1.5 OUTPUT WEIGHI G PROCEDURE ................................................................................................. 49
13.3.2 AUTOMATIC STATIC AXLE WEIGHI G ........................................................................................................ 51
13.3.2.1 CO FIGURATIO ............................................................................................................................. 51
13.3.2.2 I PUT WEIGHI G PROCEDURE ..................................................................................................... 51
13.3.2.3 STARTI G OUTPUT WEIGHI G THROUGH ID CODE ................................................................... 54
13.3.2.4 STARTI G OUTPUT WEIGHI G THROUGH LICE SE PLATE ....................................................... 54
13.3.2.5 OUTPUT WEIGHI G PROCEDURE ................................................................................................. 55
13.3.3 AUTOMATIC DY AMIC AXLE WEIGHI G ..................................................................................................... 57
13.3.3.1 CO FIGURATIO ............................................................................................................................. 57
13.3.3.2 I PUT WEIGHI G PROCEDURE ..................................................................................................... 57
13.3.3.3 STARTI G OUTPUT WEIGHI G THROUGH ID CODE ................................................................... 60

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
3
13.3.3.4 STARTI G OUTPUT WEIGHI G THROUGH LICE SE PLATE ....................................................... 60
13.3.3.5 OUTPUT WEIGHI G PROCEDURE ................................................................................................. 61
13.3.3.6 SELECTI G I PUT OR OUTPUT BEFORE OR AFTER HAVI G ACQUIRED THE AXLES ............ 63
13.3.4 OTES O THE I PUT WEIGHI G ............................................................................................................... 63
13.3.5 OTES O THE OUTPUT WEIGH ................................................................................................................. 64
13.3.6 DETERMI ATIO OF THE TRUCK’S ET WEIGHT BY SUBTRACTI G THE PRESET TARE ................... 64
13.3.7 DELETI G ALL THE I PUT MEMORY STORAGES ...................................................................................... 65
13.4 FU CTIO S OF THE AUTOMATIC AXLE WEIGHI G CYCLE (STATIC OR DY AMIC) ........................................ 65
13.4.1 CA CELLI G OF THE CYCLE ....................................................................................................................... 65
13.4.2 ERRORS O THE AUTOMATIC AXLES WEIGHT ACQUISITIO ................................................................. 66
13.4.2.1 ERROR O THE DY AMIC AXLES WEIGHT ACQUISITIO ........................................................... 66
13.4.2.2 ERROR O THE STATIC AXLES WEIGHT ACQUISITIO .............................................................. 66
13.4.3 RESET OF THE ERROR AXLE I THE DY AMIC CYCLE ............................................................................ 67
13.4.4 MA AGI G A I PUT FOR THE CYCLE START/E D ................................................................................. 67
13.4.5 MA AGI G THE OUTPUTS ........................................................................................................................... 67
13.4.6 PAUSE AXLES CAPTURI G .......................................................................................................................... 67
13.5 SETTI G AXLES SO THAT THESE ARE OT TOTALISED .................................................................................... 68
13.6 ADDITIO AL TARE FU CTIO ................................................................................................................................ 68
13.7 REE ABLI G THE WEIGH ....................................................................................................................................... 69
13.8 WEIGHT THRESOLDS FOR EXECUTI G THE WEIGH ........................................................................................... 69
13.9 VISUALISATIO A D CLEARI G OF THE ACCUMULATED TOTALS ................................................................... 69
13.10 PROGRESSIVES ..................................................................................................................................................... 70
13.10.1 PROGRESSIVE DIGITS ................................................................................................................................ 70
13.10.2 TICKET PROGRESSIVE ............................................................................................................................... 70
13.10.3 LOT PROGRESSIVE ..................................................................................................................................... 70
14. PRINTOUTS ...................................................................................................................................................................... 71
14.1 LI KI G OF THE FORMATS TO THE PRI T FU CTIO S ..................................................................................... 74
14.1.1 QUICK LI KI G OF THE FORMATS ............................................................................................................. 75
14.2 UMBER OF TICKET COPIES .................................................................................................................................. 75
14.3 REPETITIO OF THE LAST EXECUTED PRI TOUT .............................................................................................. 76
14.4 DEFAULT PRI TI G FORMATS............................................................................................................................... 76
15. OTHER FUNCTIONS ........................................................................................................................................................ 76
15.1 DIAG OSTIC PERIPHERALS ................................................................................................................................... 76
15.2 COM DATA DIAG OSTIC ......................................................................................................................................... 76
15.3 CALCULATOR ........................................................................................................................................................... 77
15.3.1 HELP FU CTIO ............................................................................................................................................ 77
15.4 DISPLAY OF ET WEIGHT WITH SE SITIVITY X 10 (for testing use during calibration) ........................................ 77
15.5 SETTI G DATE / TIME .............................................................................................................................................. 77
15.6 SET-POI T FU CTIO ............................................................................................................................................. 78
DECLARATION OF CONFORMITY ....................................................................................................................................... 82
WARRANTY ........................................................................................................................................................................... 82

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
4
1. INTRODUCTION
This manual was created to help you install and learn all about the functional possibilities of the purchased indicator.
The instrument is suitable for use in various weighing environments.
ot only does it have all the normal features of high-precision scales, but it also gives you the possibility to work in specific
environments due to the functioning modes contained in the software implemented in the FLASH MEMORY on the internal
board; This makes the instrument extremely flexible and it can be used in many different industrial applications linked to
weighing. The double numerical and interactive alphanumerical display, the alphanumerical and function keyboard, allow the
operator an easy and immediate use and provide the microcontroller with DATA E TRY functions in addition to the normal
weighing functions. The input/output allows the instrument to control various external devices, to receive external commands,
control a printer and communicate with a personal computer or to be inserted in a network of weight indicators controlled by a
PC.
WARNING
Please note that this instrument is covered by a warranty and MUST NOT BE OPENED BY THE USER for any reason
whatsoever. Any attempt to repair or modify the unit exposes the user to the risk of electric shock and will invalidate the entire
warranty.
If any problems are found in the unit or with the system in which it is used, the fact must be communicated to the
manufacturer or the dealer from whom it was purchased.
In any case, DISCONNECT THE POWER SUPPLY before taking any action.
With the 6V rechargeable battery ver ion, it ha to be completely recharged (12 hour ) in the fir t in tallation of the
in trument; we RECOMMEND di connecting the battery if the in trument i not going to be u ed for more than 30
day . In order to avoid the deterioration of the rechargeable battery:
- In tandard condition , never leave the battery partially or completely uncharged; at lea t once a week recharge it
completely.
- In ca e the in trument i not u ed for a long period, one need to
1. completely recharge the battery before the y tem i witched off for the la t time;
2. recharge completely every 3 month .
Do not pour liquid on the weight indicator.
Do not u e olvent to clean the weight indicator.
Do not expo e the in trument to direct unlight nor place it near heat ource .
Place or anchor the weight indicator and platform on a non-vibrating ba e.
All the connection of the indicator have to be made re pecting
the rule applicable in the zone and in the in talling environment.
Read carefully and apply what i de cribed in the ection 3.
Do not in tall in any area where there i a ri k of explo ion.
The crossed-out wheeled bin on the product means that at the product end of life, it must be taken to
separate collection or to the reseller when a new equivalent type of equipment is purchased. The
adequate differentiated refuse collection in having the product recycled, helps to avoid possible negative
effects on the environment and health and supports the recycling of the materials of which the equipment
is made. The unlawful disposal of the product by the user will entail fines foreseen by the current
regulations.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
5
2. MAIN TECHNICAL SPECIFICATIONS
POWER SUPPLY
3590E
:
- 12 Vdc ( 8 ÷ 36 Vdc in the IO versions), with internal 100 ÷ 240 Vac (50÷60 Hz)
/ 12 Vdc adapter.
- 6 Vdc from rechargeable built-in battery, fitted depending on the model.
CPWE:
- 8 ÷ 2436 Vdc
- 6 Vdc from external rechargeable battery (upon request).
CPWET:
12 Vdc with external 100 ÷ 240 Vac (50÷60 Hz) / 12 Vdc adapter.
6 Vdc from external rechargeable battery (upon request).
MAXIMUM POWER
16 VA.
OPERATI G TEMPERATURE
From
-
10 to +40 °C.
CO VERTER
24 bit Sigma Delta.
CO VERSIO SPEED
200 conv./sec with automatic selection.
RA GE OF I PUT SIG AL
0,6 mV/V
-
3,2 mV/V.
MI IMUM VOLTAGE PER DIVISIO 0.3
µ
V (approved instrument); 0.03
µ
V (non-approved instrument).
AUTOMATIC ZERO DETECTIO
Only in gross mode
, programmable at +/
-
¼, ½, 1, 2 divisions.
ZERO RA GE
Configurable up t
o +/
-
50
%
of max load capacity.
AUTO ZERO AT START
-
UP
Configurable up to +/
-
50
%
of max load capacity.
LOAD CELL POWER SUPPLY
5Vdc ± 5%, 120mA
(max 8 350
-
Ohm cells).
LOAD CELL CO ECTIO S
6 wires with Remote Sense.
DISPLAY DIVISIO S
10000e, 3 x 3000e f
or legal for trade weighing, expandable up to 800.000 for
internal use (with minimum signal coming from the 1,6 mV/V cell).
DISPLAYS
3590E:
- Red, high-luminosity LED indicators, with six digits (h 13 mm).
- Back lit graphic 160x32 dot LCD.
CPWE: Back lit graphic 160x32 dot LCD.
DATABASE/MEMORY
Database of 500 customers
(
3
descriptions of 20 characters).
Database of 500 products (2 descriptions of 20 characters).
Database of 500 vehicles (description of 20 characters, plate of 10 characters,
linked tare).
SIG ALS
3590E:
16 status LEDs. Graphic icons on LCD display.
CPWE: Graphic icons on LCD display.
CPWET: 3-way control light. Graphic icons on LCD display
KEYBOARD
I
mpermeable polycarbonate keyboard with 24 multifunction
(IP65 protection
degree), with membrane keys with audible and tactile feedback.
PARAMETER SETUP
Calibration and linearity (up to 8 points), fully digital and programmable from the
keyboard or from PC with Dinitools ™.
CLOCK/DATE
Fitted
, with buffer RAM.
SERIAL OUTPUTS
-
2 input/output RS232 ports on terminal board/ amp connector.
- 1 input/output RS485 port on terminal board or RS232 on amp connector.
- Management of PC keyboard or barcode reader
I PUTS A D OUTPUTS
3590EXP
,
3590EXT
and
CPWET
:
- 2 optoisolated inputs (optoisolated photo couplers), 12Vdc – 24Vdc, 20mA max
- 4 outputs (optoisolated photomosfets), 48Vac / 0.15A, 60Vdc / 0.15A, 10 Ω
max.
3590EXT (in IO version) and CPWE:
- 8 inputs (optoisolated photo couplers), 12Vdc – 24Vdc, 20mA max.
- 16 outputs (optoisolated photomosfets), 48Vac / 0.15A, 60Vdc / 0.15A.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
6
A ALOGUE OUTPUT (Option
available on the 3590EXT in IO version
and CPWE version)
-
16
-
bit analogue output configurab
le from keyboard (full
-
scale value; zero scale
value and minimum value) from 0 to 10 Vdc, from 0 to 20mA or from 4 to 20mA;
the maximum resistance applicable on the output current is 350 Ohm and the
minimum resistance applicable on the output voltage is 10 kohm.
2.1 ACCESSORIES AVAILABLE
On the indicator is possible to implement internal and external modules used to increase interfacing possibilities.
For example, the number of usable outputs, various types of printers, in order to have a report of the weighs made, or giant
display in order to better see the weigh operations. Also, one can connect a PC in order to simply program the instrument
through Dinitools™, or in order to have a complete management of the weighs.
Contact the reseller for the list of the available hardware and software accessories.
2.2 SYMBOLS USED
Below are the ymbol or text u ed in the manual to recall the reader’ attention and on the in trument to recall the
u er’ attention
ATTE TIO !
Only qualified personnel must perform this operation
ATTE TIO !
This is referred to working on energized lines: only qualified personnel must require or perform
this operation.
CE CO FORMITY
IDE TIFIES THE CLASS OF PRECISIO .
“TECH.MAN.REF.”
It means that an advanced function is being described (therefore for the technical personnel)
which will be further explained in the corresponding technical manual.
THE INSTRUMENT’S DANGEROUS VOLTAGE PARTS AND THE PARTS THE USER CAN ACCESS HAVE BEEN
ELECTRICALLY INSULATED.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
7
Figure 1
3. INSTALLATION
3.1 CPWE DRILLING TEMPLATE, CASE AND DIMENSIONS
The weight indicator has an anodized aluminium case, whose external dimensions are shown in the figure 1.
It should be mounted on a panel board respecting the safety norms.
DRILLING TEMPLATE DIMENSION: 187,5mm x 91,5mm

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
8
Figure 2
–
Measurements and dimensions in mm
1) RJ45 connector
2) Fixing for shelf or column mounting
3/5) Available for load cells / serial lines / inputs / outputs.
4) Power supply input.
3.2 3590E CASE AND DIMENSIONS
3.2.1 ABS MODEL
The indicator has an IP65 ABS case, whose external dimensions are shown in the Figure 2. It can be simply put on a table
or fixed to a shelf; or on a column, available on request.
NOTE: If the identification plate i upplied eparately (therefore not attached to the indicator), it i advi able to
attach it to the indicator, in order to be able to identify the in trument.
1
2
3 4 5

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
9
Figure 3
–
Measurements and dimensions in mm
1) RJ45 connector
2) Fixing for shelf or column mounting
3) Available for load cells / serial lines / inputs / outputs.
4) Power supply input.
3.2.2 STAINLESS STEEL MODEL
The indicator has a STAI LESS STEEL case, whose external dimensions are shown in the Figure 3. It can be simply put on
a table or fixed to a shelf; or on a column, available on request.
NOTE: If the identification plate i upplied eparately (therefore not attached to the indicator), it i advi able to
attach it to the indicator, in order to be able to identify the in trument.
1
2
3 4
3

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
10
Figure 4
–
Measurements and dimensions in mm
1/2) Available for load cells / serial lines / inputs / outputs
3) Power supply input.
4) RJ45 connector
3.3 CPWET CASE AND DIMENSIONS
The weight indicator has a STAI LESS STEEL case, whose external dimensions are shown in the figure 4. The instrument
may be installed on the wall.
NOTE: If the identification plate i upplied eparately (therefore not attached to the indicator), it i advi able to
attach it to the indicator, in order to be able to identify the in trument.
1 2 3 4

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
11
3.4 POWER SUPPLY
- The 3590E indicator is powered with 12Vdc voltage ( 8 ÷ 36 Vdc in the IO version), through an internal adapter which
converts the 100 ÷ 240Vac, 50÷60Hz mains voltage and 6 Vdc, from the built-in battery (fitted, depending on the model).
TO POWER the instrument through the 240 Vac mains, or TO RECHARGE the battery, insert the plug and the adapter to the
240 Vac mains socket.
- The CPWE indicator is powered with 8÷36 Vdc voltage or with 6 Vdc external battery (upon request).
- The CPWET indicator is powered with 12 Vdc voltage or with 6 Vdc external battery (upon request).
To connect it to the power mains, the safety regulations must be observed, including the use of a "clean" line without
disturbances or interference caused by other electronic equipment.
Ver ion with rechargeable battery: the battery inside the indicator, lasts about 25 hours (without the expansion board, with
1-cell platform) and it needs a recharging time of about 12 hours.
BATTERY FEATURES
Material LEAD
Power 4,5 Ah
Voltage 6 V
THE BATTERY MUST BE SUPPLIED DIRECTLY FROM THE MANUFACTURER.
NOTE: it is advisable to completely recharge it (12 hours) in the first installation of the instrument; we RECO END
disconnecting the battery if the instrument is not going to be used for more than 30 days.
Do not connect other equipment to the ame ocket a the one that the adapter i in.
Do not tep on or cru h the power upply cable
3.5 START UP
TO TURN ON the 3590E or the CPWET press the C key until the display turns on; then release.
The CPWE instead is automatically turned on as soon as it is powered.
The display shows:
-Initially a welcome message (settable in the TECH ICAL SET-UP, << LoGo >> StEP, TECH.MAN.REF) while the
instrument carries out a series of checking and preheating self tests.
-E-AF09 - XX name of the installed software, in which XX identifies the software language.
XX.YY is the software version installed.
- “EXECUTIO AUTOZERO”
The instrument carries out the "autozero at start-up” function: if a weight is detected within the percentile set in the <<
Auto-0 >> step (TECH.MAN.REF.), it is cleared; if the weight is not within this tolerance:
-with a non approved instrument, the display shows the weight after a few instants,
-with an approved instrument, the message “EXECUTIO AUTOZERO” appears continuously on the display, until the
weight is within tolerance.
The autozero function at start-up can be disabled in the set-up environment (only with a non approved instrument), see the
<<Auto-0>> parameter.
By pressing the 2ndF key for an instant while the version is shown in the display, the indicator will show in this order:
XX.YY in which XX indicates the instrument type, YY indicates the metrological software version.
XX.YY.ZZ is the installed software version.
HH is the installed hardware version (08).
LEGAL FOR TRADE or HIGH RESOLUTIO if the instrument is APPROVED or U APPROVED, respectively.
9.XXXXX is the g gravity value (only with APPROVED instrument).
3.6 TURNING OFF THE INSTRUMENT
TO TURN OFF the 3590E/CPWET or TO RESTART the CPWE keep the C key pressed until the “- OFF -“ message appears
on the LED display and “ *** POWER OFF *** ” on the LCD display.
TO TURN OFF the CPWE remove the instrument’s power supply.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
12
3.7 TURNING ON PRINTER IN ENERGY SAVING MODE
Premi e: the SEtuP >> SEriAL >> CoMPrn >> PWrPrn parameter must be set as “EXt.oFF” or “PWrint”,
(TECH.MAN.REF).
In a system where the indicator is connected to a printer, both are battery powered, the printer is normally maintained in
STA D-BY and powered only when a printout is needed. This function reduces the energy absorbed by the battery when the
printer is not being used.
If, in this configuration, one should power the printer to change the paper and other maintenance jobs, one needs to press in
sequence the ENTER and 0 keys during the weighing: the LED display shows Prn – on (Blinking), and the printer is kept on.
Press any key to exit from this condition.
4. FRONT PANEL KEYS
3590E:
CPWE:

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
13
CPWET
4.1 FUNCTION OF THE KEYS
In the following section, and later on in the manual, the keys’s functioning is described in accordance to how these are
configured by factory.
It is possible to customise the functionality of the keys through the << F.KEYS >> step.
C/DEL
- Turns the instrument on/off
- If pressed for an instant, it clears the tare value.
- Exits the parameter without confirming and saving the modifications.
- In the numeric input phase, it quickly clears the present value
TARE/ ZERO
-
If pressed for an instant it carries out the semiautomatic tare, or cancels the value of tare if the gross
weight is 0.
- If pressed at length, it clears the displayed gross weight, if it’s within the percentage configured in the
<< 0.PErC >> step.
Fn/ENTER
- In the alphanumeric input phase, it confirms the entry made.
- In the menu it allows to enter a step or to confirm a parameter inside a step.
2nd F
-
In the
<< F.Key >>
step, if pressed for an instant, the list of the available
functions appear
and it is possible to choose one of them.
- If pressed together with the other keys, it allows carrying out a specific function. (see section 4.1.1)

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
14
./HELP
In the calculator mode or when edits printer format, if pressed, the display
shows some help
descriptions.
In the numeric or alphanumeric input phase, it enters, in this order, the following characters: . , ; : # < > \
| ” % & / ( ) = ? ^ ’ [ ] { };
F1
In the
<< F.Key >>
step, if pressed for an instant, it is possible to set
the default key functions.
- In the numeric or alphanumeric input phase, it allows to copy entered characters.
- If pressed for an instant, it enters into the CUSTOMER DATABASE.
- If pressed at length, it locks and unlocks the instrument’s keyboard (except the C key).
F2
-
In the numeric or
alphanumeric
input phase
, it allows to stick with copied characters.
- If pressed for an instant, it enters into the MATERIAL DATABASE.
- If pressed at length, the weight visualisation function with sensitivity x 10 is enabled
F3
-
If pressed for an instant, it enters into the
VEHICLE DATABASE
.
- If pressed at length, one can adjust the date and time of the instrument.
F4
-
If pressed for an
instant
, it allows to fill in the free texts
,
(only
if configured
)
.
- If pressed at length, it enters the instrument’s diagnostics menu.
F5 - If pressed at length, it locks/unlocks the tare.
- Commands the data transmission to the printer serial port.
F6
-
If pressed for an instant, it
starts
the
simple axle totalisation or the
i
nput
axle totalisation (with
Input/Output function enabled).
- In the numeric or alphanumeric phase, it decreases the blinking digit.
- It allows scrolling ahead inside the menu steps or in the parameters within a step.
F7
-
If pressed for an instant, it
starts output axle totalisation (with Input/Output function enabled).
- In the numeric or alphanumeric input phase, it increments the blinking digit.
- It allows scrolling backwards in the menu steps or in the parameters within a step.
F8 - If pressed for an instant, it executes the printing and the zeroing of the partial total.
- In the numeric or alphanumeric input phase, it selects the digit to be modified from right to left.
F9
-
If pressed for an instant, it allows to manually close the
automatic
axl
e totalisation cycle with
consequent determination of the total weight. See section 13.2.2, 13.2.3, 13.3.2 and 13.3.3.
- In the numeric or alphanumeric input phase, it selects the digit to be modified from left to right.
F10
-
If pressed for an instant, i
t allows to reset the
automatic
axle totalisation cycle, cancelling all the
totalized axles. See section 13.4.1
- In the numeric or alphanumeric input phase, introduces a space between two characters.
NUMERIC
KEYBOARD
Entry of digits or characters.
- During weighing, these enter a numeric value with which it’s possible to:
1) Set the tare value, by pressing subsequently the TARE key (see section 7.2).
2) Sum, subtract, or multiply the value entered from the keyboard to the current tare (see the 15.3
CALCULATOR section).

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
15
4.2 "2ndF" KEY: SECOND FUNCTION OF THE KEYS
In the weighing phase, by pressing the 2ndF key together with another key, it’s possible to execute various functions
(continue reading the manual for the details of the functions):
2ndF
F1
Pri
nt/
Clearing
of Customer Total.
2ndF
F2
Print/
Clearing
of Material Total.
2ndF
F3
Print/
Clearing
of Vehicle Total.
2ndF
F4
De
selecting
all the elements selected from the database
s
.
2ndF
F5
Repetition of the last printout made.
2ndF
F8
et/Gro
ss Conversion
2ndF
F9
Change LCD visualization
2ndF
C
Causes the display of the present metric scale information
(see section 9).
4.3 ENTERING ALPHANUMERIC TEXT
It might be necessary, while the weighing system is working, to enter some alphanumerical texts such as descriptions,
alphanumerical messages (operator, lot number, customer, etc.).
To enter the characters one uses the 0 to 9 keys.
By pressing one of these keys a few times, the characters shown on the key will be shown on the display: initially the first
letter in the bottom left will appear, and then the other characters towards the right.
After digiting a character, the blinking cursor, after a few instants, advances automatically of a position.
When the maximum number of characters has been reached, the indicator emits an acoustic signal and the cursor remains
in that positions.
TAKE NOTE:
In the updating of a text, if the cursor is at the beginning of the text and the first key pressed is C or a character/number key,
all the entered characters will be deleted.
Function of the key
F5
S
witches the writing mode from “numeric”
(nu )
to “characters”
(ChAr)
.
In the nu mode one enters just the numbers, while in the ChAr mode one can enter all the characters of
a key. The la t writing mode elected i tored by the in trument.
C
If p
ressed for an instant, it
cancels the written characters: first the characters that follow the cursor are
cancelled; than those that precede it, one at a time.
If pressed at length, it deletes all entered characters.
With empty text, it exits the entry phase without confirming.
SHIFT
It enters a space in the middle of a text.
./HELP
If pressed a few times it allows entering the following characters:
. , ; : # < >
\
| ” % & / ( ) = ? ^ ’ [ ] { }.
0
In “characte
rs” mode
(ChAr),
by pressing once
,
a pace i entered;
by pressing twice it enters the “0”
character.
1
In “characters”
mode (ChAr),
when
pressed repeatedly, it
allows to enter the following symbols:
? ! 1 @ ’ + – * / = ~ € „ … † ‡ ˆ ‰ š < OE ž ı ’ “ ” • – – ˜ ™ Š > oe ž ¢ £ ¤ ¥ ¦ § ¨ © ª « ¬ - ® ‾ ° ± ² ³ ´ µ ¶ · ¸
¹ º » ¼ ½ ¾ ¿ ã.


Moves the blinking cursor to the left or to the right.


Scrolls in one sense or the other the list of all the enterable characters (0,
1…9, A, B…Y, Z)
Example :
-To enter the letter “B” one should press the “2” key twice in the ChAr mode.
-To enter the number “3” one should press the “3” key four times (in the ChAr mode) or press the F5 key (one passes to
the nu mode) and press the “3” key once.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
16
4.4 DISABLING THE KEYBOARD
It is possible to disable all the keyboard functions (except the C key for turning on and off), in order to avoid undesired
pressings of the scale keys:
-To lock the keyboard, press at length the F1 key: the display shows the “LoCK” message for a few instants. ow the
keyboard is LOCKED: if one presses a key, the display shows for a few instants the “PRESS AT LE GTH F1 FOR
U LOCKI G” message.
-To unlock the keyboard, press again at length, the F1 key: the display shows the “unLoCk” message for a few instants.
NOTE: It’s possible to lock all keys individually in a permanent way through the TECH ICAL SET-UP, TECH.MAN.REF.
4.5 HELP MENU
By pressing at length the HELP key it is possible to access a menu containing the list of keys with the relative function, and
status (locked or unlocked) indication.
The display shows:
- in the upper part: the key, followed by the code of the linked function in the << F.Key >> step, and a symbol
indicating whether the key is unlocked ( ) or locked ( ) in the << EN.KEYS >> step.
- in the lower part: the description of the linked function.
Scroll the list with the arrow keys  , press the C key to exit.
4.6 INDICATOR CONNECTED TO REMOTE KEYBOARD
It’s possible to connect a PC keyboard (optional), used to emulate the functions of the keys of the indicator.
The keys are managed in the following way:
Esc
-
C
key.
- If pressed at start-up, it allows entering in the technical set-up.
In the alphanumeric input, it deletes all entered characters.
 and Canc
-
C
key.
- If pressed at start-up, it allows entering in the technical set-up.
In the alphanumeric input, it cancels first the characters which follow the cursor, then the ones which
precede it, one at a time.
Enter

-
F
n
key.
- Confirms the entered value.
- Enters the displayed step
umeric and
alphanumeric
keys, SHIFT
and CAPS
LOCK
-
Quick entry of a numeric and alphanumeric string: through the CAPS/LOCK or SHIFT key it is possible to
switch from the capital letters to the lower case letters, and vice versa, or enter the second character
corresponding to the key (for example ", %, &, /, ? ). The entered string is shown on the LCD display.
Cursor keys


-
Scroll the parameters
- Increase or decrease the blinking digit while entering a value.
Cursor keys


-
When entering a value or an alphanumeric string, it scrolls the digits to the right or to the left.
F1, F2….F10
F1,F2….F10 keys.
F11
2ndF
key
F12
TARE
key.
F1:302

C
CUSTOMER
DATABASES

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
17
The PC keyboard also allows to enter a numeric or alphanumeric string (max.32 characters) and then press a key to execute
the corresponding quick function.
For example, if the function 122 (Input text 1 configuration) is combined to the F4 key (see << F.KEYS >> step,
TECH.MAN.REF.), through PC keyboard it’s possible to enter a text and the press F4 to quickly modify the input text 1.
NOTE: through the remote keyboard, it’s not possible to carry out the functions made by pressing the keys at length.
4.7 REMOTE CONTROL
Depending on the model of indicator, it is possible to remotely control the instrument through one of the following types of
remote controls: 19-key infrared (ir),18-key infrared (ir) or 6-key radio (rd).
The type of remote control to be used must be selected in the Setup environment, in the << inF.rEd >> step
(TECH.MAN.REF.).
NOTE: The infrared remote control are for indoor u e only.
4.7.1 “19-KEY” INFRARED REMOTE CONTROL
With this type of remote control, the functioning of the keys will be as described in the following table.
FU CTIO OF THE KEYS
KEYBOARD
KEY OR FUNCTION EMULATED
F1…F3
F1…F3 keys
C
C key
NUMERIC KEYS
Entry of digits or characters
TARE / 
Tare/zero function
or increase of a digit while entering a
value
.
. /HELP key
ZERO /

Decrease of a digit while entering a value
MODE /



Scrolls the digits to the right while entering a value
PRINT /



Confirms the entered value or enters the displ
ayed step

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
18
4.7.2 “6-KEY” RADIO REMOTE CONTROL
With this type of remote control, the functioning of each key can be programmed so that it is matched to one of the available
keys of the indicator.
This configuration must be carried out in the Setup environment, in the << inF.rEd >> step (TECH.MAN.REF.), after the
selection of this type of remote control.
By pressing the ./HELP key of the indicator, it’s possible to see, while weighing, the list of the functions matched to the keys
of the indicator and also to the keys of the remote control (see section 4.1.4 “HELP ME U”).
EXAMPLE OF CO FIGURATIO
USE OF MORE REMOTE CO TROLS WITH O LY O E I DICATOR
If one works with only an indicator, it is possible to use any 6-key remote control, without combining it to the indicator,
therefore without limiting the number of usable remote controls.
To enable this mode one has to first select “RD 6 BR” in the << inF.rEd >> (TECH.MAN.REF.).
USE OF MORE REMOTE CO TROLS WITH SEVERAL I DICATORS I THE SAME AREA
If one needs to use several indicators in the same area, it is possible to combine each remote control to the desired indicator,
in order to execute the function only on it and therefore avoid emulating the function on all indicators in use.
By enabling this mode it will be possible to combine up to 3 different remote controls (e.i. for 3 different operators) for each
indicator.
To enable this mode one has to first select “RD 6” in the << inF.rEd >> (TECH.MAN.REF.).
To link a new remote control to the indicator one has to:
- press at length 1 and 2 keys together (3 seconds).
- the instrument displays "aut.rd?"
- press the E TER key of the indicator
- the new remote control is linked
To remove the linking of a remote control one has to:
- press at length 1 and 2 keys together (3 seconds).
- the instrument displays "aut.rd?"
- press the C key of the indicator; if the remote control was previously linked, it will be removed.

3590EKR, 3590EXP, 3590EXT, CPWE, CPWET series indicator E-AF09_02_13.01_E _U
19
5. DISPLAY FUNCTIONS
During the weighing the displays are subdivided mainly in 3 sections, shown in the figure below:
-WEIGHT
-STATUS I DICATORS (led pilot lights and / or graphic symbols)
-DATA (two lines in the 3590E; one or two lines in the CPWE, depending on the weight zoom function described in the
following section). See section 5.4.
Figure 1: 3590E displays
Figure 2: CPWE/CPWET display
CUS MAT VEH
PT: 1.000kg
1 CUS MAT VEH
PT: 1.000kg
WEIGHT
STATUS
I DICATORS
STATUS
I DICATORS
DATAS
WEIGHT
STATUS
I DICATORS
STATUS
I DICATORS
DATAS