Directed 403.TL10 User manual

DB3 403.TL10
v2.29
2017 Toyota Camry (H Key)

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Key type 5
Wiring diagram 6
Locating components in the vehicle 7
Vehicle connections 8
Module programming 10
Note: The master key is REQUIRED to complete the module programming successfully. 10
Connecting the module 11
LED diagnostics and troubleshooting 12
Soft reset 14
Hard reset 14
Feature programming 15
Feature and option list 16
Limited one year consumer warranty 17
Quick reference guide 18
Contents

3403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
DB3 is an all-in-one door lock and override module.
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.

4403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Auto Headlamp Shutoff
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
Immobilizer Bypass-Data No Key Req'd
Remote Start Takeover
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status

5403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming 1Keys required for operation 0
It is important to make sure you DO NOT connect the keysense wire in the installation for each of these vehicles or you will
encounter issues when attempting to start the vehicle.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
Refer to "Vehicle connections" following the wiring diagram.
General notes: This section highlights important information for this specific firmware.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Also
please note that by default, the tach is set to 1000 rpm on hybrid vehicles.
[2] Autolight Interrupt connection required ONLY if the vehicule is equipped with automatic headlights.
[3] Parking lights, trunk release, lock and unlock connections required when not available through Data.
[4] Depending on the vehicle's trim, the TPMS Ignition Interrupt connection may be required to obtain OEM remote functionality
during runtime. Note: the TPMS light may flash during runtime.
Key type
Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.
G-stamped keys Standard Key H-stamped keys
H
For vehicles with H-stamped keys, see
the TL10 firmware.
For vehicles with G-stamped keys, see
the TL5 & TL7 firmware.
For vehicles with dot-stamped keys,
see the TL11 firmware.
Note: Some replacement keys
may not have any markings on
the key.

6403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
D2D Port
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
SIL Data: Yellow/Black: 10
RDA: Orange/Black: 11
1412
10 42
XKD2D65
16
8
9
1
Diagnostic Connector OBDII
HS CAN Low:
White, pin 14
HS CAN High:
Blue, pin 6
SIL Data:
Gray, pin 7
(AC) Tach Output: Violet/White: 5
Body ECU
Connector Body ECU Connector
(middle conn. left side of steering column)
RDA: Blue, pin 16
4 56
161718
282930
131415
25
26
27
10 11 12
22 23 24
123
789
192021
Autolight Interrupt (conn. side): Orange/Red: 10
Autolight Interrupt (veh. side): Yellow/Red: 11
(-) Ground (-) Ground
Cut
Headlight Switch
Autolight: Green, pin 20
456
1617 18 131415
10
1112
123
789
1920
67
1234
85
(+) Ignition 2:
Pink, pin 1
(+) Ignition 1:
Black, pin 6
(+) Accessory:
White, pin 2
(+) Starter:
Blue, pin 7
(+) Starter 2
Lt. Green, pin 3
(+) 12V:
Green, pin 5
Ignition
Connector
(+) Ignition 1 Output
(+) Accessory Output
(+) Starter 1 Output
(+) 12V Input
(+) Ignition 2 Output
(AC) Tach Input
(-) Parking Lights Output
(+) Starter 2 Output
TPMS Ignition Interrupt (conn. side): Yellow: 8
TPMS Ignition Interrupt (veh. side): Orange/Yellow: 9

7403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle

8403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2017 Toyota Camry (H Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN High OBD-Data Link Connector, white 16 pin plug, pin 6 Data Blue
H1/4 Tan (DATA) HS CAN Low OBD-Data Link Connector, white 16 pin plug, pin 14 Data White
H1/5 Orange/Green (DATA) HS CAN High No Connection
H1/6 Orange/Brown (DATA) HS CAN Low No Connection
H1/7 Brown Relay N.O. No Connection No Connection
H1/8 Yellow Relay COM TPMS Ignition Interrupt [4] Passenger Kick, white 18 pin plug, pin 3 Cut Yellow (TPMS)
H1/9 Orange/Yellow Relay N.C. TPMS Ignition Interrupt [4] Passenger Kick, white 18 pin plug, pin 3 Cut Yellow (TPMS)
H1/10 Orange/Red Relay N.C. Auto Light Interrupt [2] Headlight Switch, black 20 pin plug, pin 20 Cut Green
H1/11 Yellow/Red Relay COM Auto Light Interrupt [2] Headlight Switch, black 20 pin plug, pin 20 Cut Green
H1/12 Brown/Red Relay N.O. No Connection No Connection
H1/13 Red (+) W2W Only - 12 Volt Ignition Switch, white 8 pin plug, pin 5 + Green (30A)
H1/14 Black (-) W2W Only - Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter
H2/2 Green/Black No Connection No Connection
H2/3 Green/White (-) W2W Only - Door Output Remote Starter
H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter
H2/5 Violet/White (AC) W2W Only - Tach Output [1] Remote Starter
H2/6 Gray (+) W2W Only - Brake Output Remote Starter
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green No Connection No Connection
H2/9 Violet/Brown No Connection No Connection
H2/10 Yellow/Black (Data) SIL OBD-Data Link Connector, white 16 pin plug, pin 7 Data Gray
H2/11 Orange/Black (Data) RDA Body ECU on dash fuse box, white 30 pin plug, pin 16 Data Blue
H2/12 Blue/Red (-) W2W Only - Hood Output Remote Starter
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color

9403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green (-) W2W Only - Lock Input Remote Starter
H3/2 Blue (-) W2W Only - Unlock Input Remote Starter
H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter
H3/4 White/Violet (-) W2W Only - Right Slidding Door Remote Starter
H3/5 Violet/Black (-) W2W Only - Left Slidding Door Remote Starter
H3/6 White/Black No Connection No Connection
H3/7 Pink/White (+) W2W Only - Pk Light Input Remote Starter
H3/8 Violet No Connection No Connection
H3/9 Pink (+) W2W Only - Ignition Input Ignition Switch, white 8 pin plug, pin 6 + Black
H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Green (Data) TX
H4/2 Black (-) Ground
H4/3 Blue (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A No Connection
H5/2 N/A No Connection
Additional remote start connections
(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)
Wire Connects To
Wire Location (+/-) Wire Color
12 Volts Ignition Switch, white 8 pin plug, pin 5 + Green (30A)
Accessory Ignition Switch, white 8 pin plug, pin 2 + White
Ignition Ignition Switch, white 8 pin plug, pin 6 + Black
Parking Lights - Headlight Switch, black 20 pin plug, pin 18 - Black
Second Ignition Ignition Switch, white 8 pin plug, pin 1 + Pink
Second Starter Ignition Switch, white 8 pin plug, pin 3 + Lt. Green
Starter Ignition Switch, white 8 pin plug, pin 7 + Blue

10 403.TL10 2.29 2017 Toyota Camry (H Key)
©2022 VOXX•DEI LLC. All rights reserved.
Module programming
Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes.
Note: The master key is REQUIRED to complete the module programming successfully.
1
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press the
programming button 5 times.
2
Insert and turn the key to the ignition position. Wait for the LED to turn on solid green for 3
seconds, and turn OFF.
Note: If transponder programming was skipped, the LED turns ON solid orange for 3
seconds then shuts OFF when programming is done.
3Turn the key to the OFF position, and remove it from the ignition barrel.
You have successfully completed the module programming sequence.