DirectOut Technologies SG.MADI User manual

SG.MADI
User‘s Manual
Version 1.2

page 2 of 56
SG.MADI Manual - Version 1.2
Copyright
All rights reserved. Permission to reprint or electronically reproduce any document or
graphic in whole or in part for any reason is expressly prohibited, unless prior written
consent is obtained from the DirectOut GmbH.
All trademarks and registered trademarks belong to their respective owners. It cannot
be guaranteed that all product names, products, trademarks, requisitions, regulations,
guidelines, specifications and norms are free from trade mark rights of third parties.
All entries in this document have been thoroughly checked; however no guarantee for
correctness can be given.
DirectOut GmbH cannot be held responsible for any misleading or incorrect
information provided throughout this manual.
DirectOut GmbH reserves the right to change specifications at any time without notice.
DirectOut Technologies® is a registered trademark of the DirectOut GmbH.
© DirectOut GmbH, 2017

page 3 of 56
SG.MADI Manual - Version 1.2
Table of contents
About This Manual 5
How to Use This Manual............................................................................... 5
Conventions .................................................................................................. 5
CHAPTER 1: Overview 6
Introduction ................................................................................................... 6
Feature Summary.......................................................................................... 6
How it works................................................................................................. 6
Applications................................................................................................... 7
CHAPTER 2: Legal issues & facts 8
Before Installing This Device ......................................................................... 8
Defective Parts/Modules ............................................................................. 8
First Aid (in case of electric shock)................................................................ 9
Updates ....................................................................................................... 10
Conditions of Warranty ............................................................................... 10
Intended Operation .................................................................................... 10
Conformity & Certificates ........................................................................... 11
Contact........................................................................................................ 11
Contents...................................................................................................... 12
Accessory.................................................................................................... 13
CHAPTER 3: Installation 14
Installing the Device .................................................................................... 14
CHAPTER 4: Operation 21
Global Control.............................................................................................. 21
Introduction ................................................................................................. 21
MADI Signals .............................................................................................. 22
Analog Signals............................................................................................. 23
Network ...................................................................................................... 24
Clocking....................................................................................................... 25
Sample Rate................................................................................................ 26
Termination.................................................................................................. 27
SG State ...................................................................................................... 27
GPI / GPO.................................................................................................... 28
CHAPTER 5: Controlling 29
SoundGrid host ........................................................................................... 29
SG.MADI Control ........................................................................................ 32
CHAPTER 6: Troubleshooting and Maintenance 48
Troubleshooting........................................................................................... 48
Maintenance................................................................................................ 49

page 4 of 56
SG.MADI Manual - Version 1.2
CHAPTER 7: Technical Data 50
Appendix A - Wiring Sketches 52
DSUB-9 (female) - GPI ................................................................................ 52
DSUB-9 (female) - GPO............................................................................... 52
Index 53

page 5 of 56
SG.MADI Manual - Version 1.2
About This Manual
About This Manual
How to Use This Manual
This manual guides you through the installation and operation of the device.
Use the Table of Contents at the beginning of the manual or Index Directory at the
end of the document to locate help on a particular topic. You can access more
information and latest news by visiting on the DirectOut website at
www.directout.eu.
Conventions
The following symbols are used to draw your attention to:
TIPS!
indicate useful hints and shortcuts.
NOTES!
are used for important points of clarification or cross references.
WARNINGS!
alert you when an action should always be observed.

page 6 of 56 SG.MADI Manual - Version 1.2
CHAPTER 1: Overview
CHAPTER 1: Overview
Introduction
SG.MADI is a SoundGrid / MADI converter linking SoundGrid® and MADI (AES10),
offering extra features tailored for broadcast, live and studio applications.
SoundGrid® is a layer2-based network protocol offered by Waves for Audio-over-
Ethernet networking and real-time processing solutions to deliver uncompressed,
multi-channel, low-latency digital audio over Ethernet networks.
Feature Summary
MADI Ports 2 x I/O ports - individually configurable
with BNC coaxial, SC optical or SFP
MADI Formats 56/64 channel, 48k/96k Frame
Sample Rates 44.1, 48, 88.2, 96 kHz +/-12.5%
Network 2 x RJ45 Socket (1 Gbit/s), 128 channels (I/O)
Mic Input 2 x XLR, phantom power switchable
Line Out 2 x XLR, balanced with trim controller
Headphone Out 1 x 6.3 mm TRS jack,
unbalanced with trim controller
Audio Driver Windows® (ASIO), macOS® (Core Audio)
Power Supply This device is equipped with two wide range power
supplies (84 V to 264 V AC / 47 Hz to 63 Hz / safety
class 1)
How it works
The device is controlled via network from a computer running the SoundGrid
Studio application which is used for configuring and patching hardware and
software I/Os on the SoundGrid network and the local SoundGrid ASIO/Core Audio
driver.
Available I/Os:
• 128 channels network audio I/O, SoundGrid
• 128 channels MADI I/O
• 2 channels analog I/O + Headphones output

page 7 of 56SG.MADI Manual - Version 1.2
CHAPTER 1: Overview
Applications
SG.MADI meets a rich set of challenging applications:
• multi-stage venues connecting MADI and SoundGrid® consoles
• monitoring SoundGrid® and MADI signals
• inserting SoundGrid®DSP Server with Waves plug-ins into a MADI
environment
• integrating outboard equipment and DAWs to a SoundGrid® environment
• remote control of external components via SoundGrid® / MADI
Scheme
SoundGrid MADI
IN
IN/OUT
128ch 64ch 64ch
64ch 64ch 2ch
2ch
2ch
IN
OUT OUT PHONES
ANALOG

page 8 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
CHAPTER 2: Legal issues & facts
Before Installing This Device
WARNING!
Please read and observe all of the following notes before installing
this product:
• Check the hardware device for transport damage.
• Any devices showing signs of mechanical damage or damage from the
spillage of liquids must not be connected to the mains supply, or
disconnected from the mains immediately by pulling out the power lead.
• All devices must be grounded. The device is grounded through its
IEC power connections.
• All devices must be connected to the mains using the three-cord power
leads supplied with the system. Only supply electrical interfaces with the
voltages and signals described in these instructions.
• Do not use the device at extreme temperatures. Proper operation can
only be guaranteed between temperatures of 5ºC and 45ºC and a
maximum relative humidity of 80%, non-condensing.
• The cabinet of the device will heat up. Do not place the device close
to heating sources (e.g. heaters). Observe the environmental conditions.
Defective Parts/Modules
WARNING!
This device contains no user-serviceable parts. Therefore do not open the device.
In the event of a hardware defect, please send the device to your DirectOut
representative together with a detailed description of the fault.
We would like to remind you to please check carefully whether the failure is
caused by erroneous configuration, operation or connection before sending parts
for repair.

page 9 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
First Aid (in case of electric shock)
WARNING!
• Do not touch the person or his/her clothing before power is turned off,
otherwise you risk sustaining an electric shock yourself.
• Separate the person as quickly as possible from the electric power source
as follows:
- Switch off the equipment.
- Unplug or disconnect the mains cable.
• Move the person away from the power source by using dry insulating
material (such as wood or plastic).
• If the person is unconscious:
- Check their pulse and reanimate if their respiration is poor.
- Lay the body down and turn it to one side. Call for a doctor immediately.
• Having sustained an electric shock, always consult a doctor.

page 10 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
Updates
DirectOut products are continually in development, and therefore the information
in this manual may be superseded by new releases. To access the latest
documentation, please visit the DirectOut website:
www.directout.eu.
WARNING!
No compensation can be claimed for damages caused by operation of this unit
other than for the intended use described above. Consecutive damages are also
excluded explicitly. The general terms and conditions of business of DirectOut
GmbH are applied.
Conditions of Warranty
This unit has been designed and examined carefully by the manufacturer and
complies with actual norms and directives.
Warranty is granted by DirectOut GmbH over the period of two years for all
components that are essential for proper and intended operation of the device. The
date of purchase is applied for this period.
Consumable parts (e.g. battery) are excluded from warranty claims.
WARNING!
All claims of warranty will expire once the device has been opened or modified, or
if instructions and warnings were ignored.
For warranty claims please contact the dealer where your device was acquired.
Intended Operation
SG.MADI is designed for conversion / routing between network audio and MADI
signals. MADI refers to AES10, network audio refers to SoundGrid® from Waves.

page 11 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
Conformity & Certificates
CE
This device complies with the basic requests of applicable EU guidelines. The
appropriate procedure for approval has been carried out.
RoHS
(Restriction of the use of certain Hazardous Substances)
This device was constructed fulfilling the directive on the restriction of the use of
certain hazardous substances in electrical and electronic equipment 2002/95/EC.
WEEE
(Directive on Waste Electrical and Electronic Equipment)
Due to the directive 2002/96/EC for waste disposal this device must be recycled.
For correct recycling please dispatch the device to:
DirectOut GmbH,
Leipziger Str. 32
09648 Mittweida
Germany
Only stamped parcels will be accepted!
WEEE-Reg.-No. DE 64879540
Contact
DirectOut GmbH
Leipziger Str. 32, 09648 Mittweida, Germany
Phone: [phone]
Fax: [phone]
Mail: [email protected]
www.directout.eu

page 12 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
Contents
The contents of your SG.MADI package should include:
• 1 x SG.MADI (19’’, 1 RU)
• 2 x power chord
• 1 x fixing unit for power plug
• 1 x Manual
To complete the delivery please download from the
Waves website: www.waves.com
• Waves Central
You will need to register with a Waves account.

page 13 of 56
SG.MADI Manual - Version 1.2
CHAPTER 2: Legal issues & facts
Two different optical SFP transceiver are available from DirectOut GmbH:
• Multimode SFP transceiver with LC connectors (No: DOICT0129)
• Singlemode SFP transceiver with LC connectors (No: DOICT0130)
Specification of the optical SFP modules:
SFP Multimode Singlemode
Wavelength TX 1310 nm 1310 nm
Wavelenght RX 1310 nm 1310 nm
Distance 2 km 10 km
Powerbudget (dB) 11 dB 12 dB
Protocols Fast Ethernet OC3/STM1 Gigabit Ethernet, Gigabit
Fibre Channel
Bandwidth from 100 Mbit/s 1.050 Gbit/s
Bandwidth 155 Mbit/s 1.250 Gbit/s
Laser FP FP
Receiver Type PIN PIN
Connector LC LC
Wavelength TX min 1260 nm 1260 nm
Wavelength TX max 1360 nm 1360 nm
Wavelength RX min 1260 nm 1260 nm
Wavelength RX max 1620 nm 1600 nm
Transmit min - 19.00 dBm - 9.00 dBm
Transmit max - 14.00 dBm - 3.00 dBm
Receive min - 30 dBm - 21.00 dBm
Receive max
(Receiver overload)
- 5.00 dBm - 3.00 dBm
Temperature (min) 0° Celsius 0° Celsius
Temperature (max) 70° Celsius 70° Celsius
Type of DDM/DOM internal internal
Extinction Ratio 8.20 dB 9 dB
Accessory

page 14 of 56 SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
Retain the protective cap if the optical port is unused. This will protect against
soiling which can lead to malfunction.
Avoid damage from condensation by waiting for the device to adapt to the
environmental temperature. Proper operation can only be guaranteed between
temperatures of 5ºC and 45ºC and a maximum relative humidity of 80%, non-
condensing.
Ensure that the unit has sufficient air circulation for cooling.
CHAPTER 3: Installation
Installing the Device
1. Open the packaging and check that the contents have been delivered
complete and undamaged.
2. Fix the device in a 19’’ frame with four screws, or place it on a non-slip
horizontal surface.
WARNING!
3. Remove the protective cap from the optical MADI port(s) before use.
NOTE!
4. Connect signal cable(s) for the MADI signals.
WARNING!
All module slots must be fitted with a module each. Otherwise live parts
become accessible which may cause serious harm to your health. An open
housing may also cause inappropriate operation conditions due to an insufficient
electromagnetic shielding.

page 15 of 56SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
5. Plug in the network cable to the ethernet port(s) to connect the device with
your computer.
NOTE
If you are using one SG.MADI unit, connect it directly to your computer’s gigabit
ethernet port using the supplied cable.
If you are using multiple interfaces, connect them all to a SoundGrid-compatible
switch, and connect the switch to your computer’s ethernet port.
A list of approved switches is available at:
www.waves.com > Products > Hardware > SoundGrid Switches.
6. Using the power cord provided connect the PSUs to a matching power
supply:
WARNING!
This device must be connected to the mains using the three-cord power leads
supplied with the system. Only supply the voltages and signals indicated (84 V –
264V).
7. Turn on the power switch.

page 16 of 56 SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
8. Download ‘Waves Central’ for Mac or PC, as needed.
Link: www.waves.com > Downloads > Latest Version
9. Run the installer and follow the onscreen instructions when finished.
Launch Waves Central.
10. Click on ‘INSTALL PRODUCTS’.

page 17 of 56SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
11. Select ‘Online’ in the leftmost column to install from online. The login dialog
will appear. Login with your Waves account.
12.Search ‘All Waves products’ for ‘directout’.

page 18 of 56 SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
13.Choose ‘DirectOut SG.MADI Driver 9’ to move it to the rightmost installation
column and click the button ‘INSTALL’ to start the installation process.
14. Restart your computer.

page 19 of 56SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
15. Launch ‘SoundGrid Studio’ and follow the instructions.
SoundGrid Studio will scan the network for devices and update the device’s
firmware if necessary.
WARNING
Never disconnect any connection (network, power supply) during the firmware
update process. Disconnecting may lead to a defective device state which may
require to return the device to factory.

page 20 of 56 SG.MADI Manual - Version 1.2
CHAPTER 3: Installation
Keep any packaging in order to protect the device should it need to be dispatched
for service.
Firmware update running.
16. Restart the SG.MADI device after the update.
The control panel is described in „CHAPTER 5: Controlling“ on page 29.
TIP