Disc Makers reflex series User manual

tReflex Duplicator Manual
- 1 -
Table of Contents
Welcome Page2
Before you start Page 2
Tutorial Guide
I. Make Disc-to-Disc Copies Page 4
II. Make Hard Drive (HDD) to Disc Copies Page 7
III. Select the Duplication Speed Page 14
IV. Select the Master Reading Source Page 17
V. Load Master Disc onto the Hard Drive Page 20
VI. Rename Existing HDD Partition Name Page 23
VII. Delete HDD Partitions Page 26
VIII. Change SETUP settings Page 39
IX. Audio CD Editing Page 30
X. Account Management Feature Page 40
XI. Duplication Mode Page 45
XII. Using AUTOSTART Feature Page 49
XIII. Using the USB Option Page 51
Menu Overview Page 52
1.Copy Page52
2. Print
3. Advanced Copy Options Page
52
4.Image Page52
5.Audio Page53
6. SETUP Page 53
7. Utilities Page 55
8. SHUTDOWN Page 57
9. Autocopy
Troubleshooting Page 57
Load Default Settings Page 60
tReflex Duplicator Manual
- 2 -
Welcome!
Thank you for buying this Disc Makers duplicator. The Reflex DVD
and CD duplicator will make it easier than ever to duplicate vast
quantities of discs. This manual contains detailed information
about using all the features in your stand-alone Reflex duplicator.
******************************************************
Before you start:
Before you start using this duplicator, please read the following to
ensure proper operation:
1. DVD Duplication Limitations:
This duplicator, it will not copy any DVD that has Copy
Protection encoded inside. DVDs you purchase or rent from a
store will be Copy Protected.
In addition to the copy protection limitation, the duplicator
will only copy a DVD-5 format (4.7GB) disc to DVD-5 format
(4.7GB) recordable DVD media. If your duplicator has double
layer capability, you can copy a DVD-9 format (8.5GB) disc to
DVD-9 format (8.5GB) recordable DVD media. You cannot
duplicate a DVD5 format disc to a DVD9 format recordable
media or vice versa.
2. Temperature Warning:
If the duplicator was stored in a location where the
temperature dropped below 32ðF (0ðC) within the past 24
hours, please leave the duplicator in a warm room with
temperatures at least 65ðF (19ðC) for 4 hours prior to

tReflex Duplicator Manual
- 3 -
powering it on for the first time. Failure to do so may cause
irreparable harm and prevent the duplicator from functioning.
tReflex Duplicator Manual
- 4 -
3. Maintenance:
It is very important to operate and keep the duplicator in a
dust free, clean environment since dust is the number 1 killer
for CD/DVD recording devices. Failure to do so may severely
damage your duplicator. We strongly suggest you place an
Air Cleaner next to the duplicator and constantly use the Air
Duster (Can Air) to clear off any dust on the surface of the
duplicator.
Do not try to use Air Duster to clean the
duplicator while the reader/writer trays are open.
In doing so, you may inadvertently blow dust
into the recording device and damage the
recording device.
4. Proper Shutdown:
To avoid possible system failures the duplicator must be
shutdown properly. To shutdown the duplicator, use the UP or
DOWN arrow keys or the ‘Shutdown“ hot key and follow
instructions on the screen. Turning off your duplicator without
performing this function will increase the risk of damaging
your duplicator.

tReflex Duplicator Manual
- 5 -
Tutorial Guide:
I. Make Disc-to-Disc Copies
This process will copy your master disc to several blank discs
simultaneously.
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
1. Make sure the Master Reading Source is set to the
READER.
It is very important to make sure that your current Master
Reading Source is the top tray in order to avoid
unnecessary error messages. To check the Master Reading
Source, please do the following:
a. Press the Source hot key under the display to navigate
to the following screen.
b. Use the bottom arrow key to scroll to Drive 1.
c. Press ENT to submit your selection.
Disc Makers 1.12
1. COPY
Hard Drive Port0.0
Drive 1 Port 1.0
tReflex Duplicator Manual
- 6 -
2. Go back to 1.COPY Menu.
a. Use UP or DOWN arrow button to navigate to the
following screen:
3. Start the Copy Process.
a. Insert your master disc and your blank discs into the
corresponding tray(s) and press ENT button to enter
COPY menu. You will see the duplicator mode menu like
below:
b. Press ENT
Disc Makers 1.12
1. COPY
Duplication Mode:
On The Fly
Drive 1 Port 1.0
Selected!
Preparing…
Waiting For Master
Copying… 10M
0 1% 1M

tReflex Duplicator Manual
- 7 -
Once the duplication run is completed, the successful copies will
be ejected and you shall see the following screen:
c. Simply insert more blank media if more copies are
needed or press ESC to return to 1.Copy
It is normal to see the progress indicator stays at 0-
10% and 100% for approximately 30 seconds for
CD duplication and up to 1 minute for DVD
duplication. This is caused by the initializing and
finalizing stage.
O
PASS 7 FAIL 0( 7)
W
aiting for Blanks
- “PASS 7” indicates that you’ve
just made 7 successful copies.
- “FAIL 0” indicates that you
have no failure in this run.
- “7” indicates that you’ve
successfully copied 7 copies so
far.
Pass 1 Fail 0 ( 1)
Waiting For Blanks
tReflex Duplicator Manual
- 8 -
If you happen to have any failed discs (bad copy),
the failed disc(s) will not be ejected automatically.
You need to manually eject them and throw them
away if they are write once recordable disc(s).
For detail information, please review Tutorial Guide XII:
Introduction to Duplication Mode.
Tutorial Guide:
II. Make Hard Drive(HDD)-to-Disc Copies
Copying from the Hard Drive is the best way to make copies!
There are 3 benefits to copying from the Hard Drive:
i. Performance - Duplicating from the Hard Drive will be
able to boost the DVD duplication speed.
ii. Stability - Duplicating from Hard Drive will stabilize the
duplication process compared to the Disc to Disc
process.
iii. Convenience - With your master discs stored inside the
Hard Drive, you can have access to each one easily.
There is no need to carry your master discs; they are all
stored inside the duplicator.
Your built-in Hard Drive will be divided into a number of
partitions. Each partition will hold ONE and ONLY ONE
master disc regardless of the capacity of your master disc.

tReflex Duplicator Manual
- 9 -
The number of partitions is determined by dividing your Hard
Driveís total capacity by 1GB for CD format, 5GB for DVD-5
format or 9GB for DVD-9 format (Double Layer) and
subtracting one partition for system use.
The following steps will show you how to load your master
disc into the installed Hard Drive as a disc image and copy the
stored disc image into several blank discs. This process is
recommended for large volume production.
How to make copies from the Hard Drive?
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
1. Make sure the Master Reading Source is set to the Hard
Drive.
It is very important to make sure the Master Reading Source
is set to the Hard Drive in order to avoid unnecessary error
messages. To check the Master Reading Source, please do
the following:
a. Press Source button below the display and you
shall see the following:
DISCMAKERS 1.12
1.COPY
Drive 1 Port 1.0
Optiarc DVD R AD5170A
tReflex Duplicator Manual
- 10 -
b. Scroll up to this screen:
c. Press ENT
d. The screen should go back to:
2. Copying From the Hard Drive
a. Insert desired number of blank media
H
ard Drive Port 0.0
Hitachi HDT725025UL
D
iscmakers 1.12
1. Copy
D
ISCMAKERS 1.12
1. Copy
H
ard Drive Port 0.0
Selected!

tReflex Duplicator Manual
- 11 -
b. Press ENT and select the partition you want to burn.
c. Press ENT.
Please allow 5-10 seconds for the duplicator to detect your Hard
Drive partition and Blank Discs as well. After your Hard Drive
partition and Blank Discs have been recognized, then you shall
see the following screen:
The unit will Auto start the copying process if all
drives are loaded and detected. If all drives are
not loaded, you will need to press ENT.
By default, the “Auto Start“ setting is set to
“Auto“. For example, if your duplicator has
detected 3 blank discs and did not detect any
additional blank discs for 30 seconds, then the
duplication will be started automatically.
Preparing… 74M
W
aiting for blanks
Preparing…
7 Disc Detected Go?
Choose Partition:
[Name] Data 74M
tReflex Duplicator Manual
- 12 -
If the WAITING FOR BLANKS screen is displayed
for more than 2 minutes, please check your Blank
Discs for quality.
d. Press ENT
After 2 or 3 seconds of processing time, the following Copy
Progress Screen will appear.
It is normal to see the progress indicator stays at 0-
10% and 100% for approximately 30 seconds for
CD duplication and up to 1 minute for DVD
duplication. This is caused by the initializing and
finalizing stages.
P
reparing...
Please Wait
C
opying
.
.. H 74M
2% 3M
- “74M” indicates the capacity o
f
the master disc.
- “2%” indicates the current
progress of the duplication..
- “H” indicates you are copying
from a Hard Drive Image.

tReflex Duplicator Manual
- 13 -
Once the duplication run is completed, the good copies
will be ejected and you shall see the following screen:
O
Next, refill more blank media to continue making more copies, or
you can press “ESC“ to terminate your project and go back to the
main menu.
If you enable the counter and specified a counter value for
your project and your project is completed, you shall see
the following screen:
If you see above message, you can press “ENT“ to go
back to main menu.
If you enabled the counter and the number of
discs you have inserted is more than what you
requested, you will receive a message regarding
you have inserted more discs than what you need.
You can continue to copy or you can eject the
extras.
21 Disc Copie
d
Press OK to Finish
PASS 7 FAIL 0( 7)
W
aiting for Blanks
- “PASS 7” indicates that you’ve
just made 7 successful copies.
- “FAIL 0” indicates that you
have no failure in this run.
- “7” indicates that you’ve
successfully copied 7 discs.
tReflex Duplicator Manual
- 14 -
If you happen to have any failed discs (bad copy),
the failed disc(s) will not be ejected automatically.
You need to manually eject them and throw them
away if they are write once recordable disc(s).
NOTES

tReflex Duplicator Manual
- 15 -
Tutorial Guide:
III. Select the Duplication Speed
This process will allow you to adjust the duplication speed
subject to your various needs.
By default, the duplication speed will be set to the optimal
speed. However, under some circumstances, you might want
to lower the duplication speed. Those circumstances are as
follows:
•Blank Media Compatibility - When your media
compatibility is not good, lowering the duplication
speed is necessary to make good copies.
•Poor Master Disc Quality - If your master disc
condition is not good, lowering the duplication
speed will reduce failure rates.
•Duplication Quality - The lower the burn speed, the
higher the quality of your duplicates. When you have
time, it is a good choice to lower down the speed to
produce the best quality duplicates.
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
1. Navigate to Speed Selection Menu.
Press UP or DOWN arrow button to navigate to the
following screen.
DISCMAKERS 1.12
1. COPY
tReflex Duplicator Manual
- 16 -
2. Press “ENT“ and the first option will be:
3. Press ENT again to access Speed Selection Menu.
Then, you can press “ENT“ button to enter into Speed
Selection Menu.
You shall see the following:
4. Select Duplication Speed Type.
There are four types of recording speed:
•CD to CD: Copy CD Disc to CD-R Discs directly. (On-The-
Fly)
•DVD to DVD: Copy DVD Disc to DVD±R Discs directly.
(On-The-Fly)***
•HDD to CD: Copy Hard Drive CD Image to CD-R Discs.
•HDD to DVD: Copy Hard Drive DVD Image to DVD±R
Discs.
Depending on what type of duplication and your duplicator
restrictions, you need to select the correct type in order to
take effect. To select the recording speed types, you need
to press UP or DOWN button to adjust and press “ENT“
button to submit your selection.
Setup
1. Select Burn Speed
D
ISCMAKERS 1.12
5. Setup
S
elect Burn Speed:
CD to CD SPEED

tReflex Duplicator Manual
- 17 -
*** To ensure the duplication quality, for certain models, you
are not allowed to adjust the duplication speed for DVD to
DVD to greater than 6x duplication speed. To achieve
maximum duplication speed, you need to perform
duplication tasks from the Hard Drive. For detailed
instructions, please refer to “Tutorial Section II - Make Hard
Drive-to-Disc Copies.“
5. Select Desired Duplication Speed.
Once you have submitted the duplication speed type, you
shall see the following:
You can press UP or DOWN button to select the desired
speed and then press “ENT“ to submit your speed selection.
6. Once your selection has been changed successfully,
you shall see the following screen for 2 seconds.
Then you will be directed back to the Setup sub-menu:
7. Press ESC twice to return to Main Menu
CD to CD Speed:
16x
CD to CD Speed:
A
djusted to: 24x
Select Burn Spee
d
CD to CD Speed
tReflex Duplicator Manual
- 18 -
Tutorial Guide:
IV. Select the Master Reading Source
When you try to make a copy, you need to specify where the
master disc is. Is it in the Reader tray? Or is it an Image
inside the Hard Drive? This tutorial will show you how to
change the Master Reading Source to satisfy your needs.
The two copy methods are:
•Disc-to-Disc copy - This is the case when you would
normally make copies on the fly. You need to set the
“Reader“ as your Master Reading Source.
•Hard Drive-to-Disc copy (if Hard Drive installed) - If you
want to make copies from your Hard Drive Image, you
need to select the source as “Hard Drive“.
There are benefits to copy from Hard Drive:
i. Performance - Duplicating form the Hard Drive will
be able to boost the DVD duplication speed to 8x
or above.
ii. Stability - Duplicating from Hard Drive will stabilize
the duplication process compared to the Disc to
Disc duplicating.
iii. Convenience - With your master discs stored inside
the Hard Drive, you can have access to each one
easily. There is no need to carry your master discs;
they are all stored inside the duplicator.

tReflex Duplicator Manual
- 19 -
When you turn on your duplicator, after it has booted up, you
should see the following signifying your duplicator is ready.
1. Press “Source“ hot key to navigate to Select Source Menu.
2. Enter Source Selection Menu.
Press “ENT“ button to enter into Source Selection Menu.
You shall see the following:
Select Desired Master Reading Device.
You can press UP or DOWN button to select the desired
Master Reading Source. Then, you can press “ENT“ to
submit your Source Selection.
3. Once your selection has been changed successfully, you
shall see the following screen for 2 seconds:
Disc Makers 1.12
1. COPY
Hard Drive Port 0.0
Hitachi HDT725025UL
Hard Drive Port 0.0
Selected!
Setup
5.2 Select Source
tReflex Duplicator Manual
- 20 -
Then you will be directed back to the menu:
After loading your master disc to the Hard Drive,
please make sure to remove your master disc from
the Master Reading Tray. Failure to do so might
cause improper duplication.
NOTES
D
ISCMAKERS 1.12
1.Copy

tReflex Duplicator Manual
- 21 -
Tutorial Guide:
V. Load Master Disc onto the Hard Drive
In order to copy from the Hard Drive, you are required to load
your master disc onto a hard drive partition.
The number of partitions is determined by dividing your Hard
Driveís total capacity by 1GB for CD format, 5GB for DVD-5
format or 9 GB for DVD-9 format (Double Layer) and subtracting
one partition for system use.
For example, if you have a 40GB Hard Drive, you can calculate
the number of DVD-5 format partitions by: 40 / 5 = 8. Since there
is 1 partition reserved for the system use, you will have 7
partitions to use.
To load your master disc onto a hard drive partition, please do
the following:
1. Load your master disc onto the Hard Drive.
a. Press the “Load“ hot key or scroll to Image to
navigate to the following screen.
b. Press “ENT“ to enter Load Partition Menu and you
shall see the following:
Select HDD as source
OK?
tReflex Duplicator Manual
- 22 -
c. Now, you have a choice to load your master disc
into a new (empty) partition or overwrite one of the
existing partitions if any exists. You can simple
press UP or DOWN arrow button to select your
partition and press “ENT“ to submit. You will see
the following:
d. Now, you can name the partition you are about to
load into the Hard Drive. To enter the name, you
need to use UP or DOWN button to select the
character and use “ENT“ or “ESC“ button to move
the cursor position and once youíve finished, move
the cursor to “OK“ and press “ENT“. For example,
if I want to name the partition of your master disc
as “FUN“. Then do the following:
E
dit Partition Name
[x ] OK?
L
oadPartition[002/16]
Overwrite[name]
L
oad Partition [ 1/ 16]
Load->New Partition
*The “1” indicates the number of partitions
you’ve already loaded into the Hard
Drive .
(Includes the Reserved Partition)
*The “16” indicates the total number of partitions
you can load to the Hard Drive.

tReflex Duplicator Manual
- 23 -
Make sure the cursor is located at the first position:
i. Press “DOWN“ button consecutively until “F“ is
displayed.
ii. Press “ENT“ button once to move the cursor to the
next position.
iii. Press “DOWN“ button consecutively until “U“ is
displayed.
iv. Press “ENT“ button once to move the cursor to the
next position.
v. Press “DOWN“ button consecutively until “N“ is
displayed.
vi. Press “ENT“ button once to move the cursor to the
next position.
vii. Now, we have the name “FUN“ displayed and
then, press “ENT“ consecutively until the cursor is
moved to “OK“.
viii. Then, press “ENT“ once to submit your name
selection.
e. Now you shall see the following confirmation screen:
f. Press “ENT“ button to confirm. Once your master disc has
been recognized. The loading progress indicator will be
displayed and you shall see the following
Load Partition?
[FUN ], OK?
tReflex Duplicator Manual
- 24 -
g. Once your master disc has been loaded completely, you
shall see the following:
Then, you can press “ENT“ button to go back to the
Image ñ Load Partition Menu.
Tutorial Guide:
VI. Rename Existing Hard Drive Partition Name
When you load your master disc to a hard drive partition,
you are asked to give it a name. However, if you donít like
the name you entered before, you can rename it at anytime
afterwards. To rename your existing hard drive partition
name, please do the following:
1. Use UP or DOWN arrow button to navigate to the
following screen.
2. Press “ENT“ and use UP or DOWN arrow button to
navigate to the following screen
L
oad Partition OK!
Press OK to Finish
D
ISCMAKERS 1.12
3. Image
L
oading ... 420M
FUN 12% 23M
*The “12%” indicates the percentage of data has
been loaded to the Hard Drive.

tReflex Duplicator Manual
- 25 -
3. Press “ENT“ to enter Rename Partition Menu and you
shall see the following:
4. Use UP or DOWN arrow button to find the desired
partition and then press “ENT“ to submit your selection
and you shall see the following confirmation screen:
5. Press “ENT“ once again to confirm it and you shall see
the following:
6. Now, you can rename the partition youíve just selected.
To enter the name, you need to use UP or DOWN
button to select the character and use “ENT“ or “ESC“
button to move the cursor position and once you
finished, move the cursor to “OK“ and press “ENT“. For
example, if I want to rename the image “FUN“ to
“FUN2“. Then do the following:
Move the cursor to the forth position by pressing “ENT“
Rename Partition
[FUN ] Data, OK?
Image
3.Rename Partition
Choose Partition:
[FUN ] Data 4M
Rename Partition
[FUN ]OK?
tReflex Duplicator Manual
- 26 -
until you reached desired location:
i. Press “DOWN“ button consecutively until “2“ is
displayed.
ii. Now, we have renamed the image name “FUN“ to
“FUN2“. So we can press “ENT“ consecutively until the
cursor is moved to “OK“.
iii. Then, press “ENT“ once to submit your name selection.
Once youíve done above, you shall see the following:
Then, you will be directed back to HDD Image Setup
Menu.
NOTES
E
nter HDD Image Name
[FUN2 ] OK
P
artition [FUN2 ]
Renamed!
I
mage
3.Rename Partition

tReflex Duplicator Manual
- 27 -
Tutorial Guide:
VII. Delete Existing Hard Drive Partition Permanently
If for some reason you would like to delete your existing
hard drive partition permanently, you can do the following:
1. Use UP or DOWN arrow button to navigate to the
following screen.
2. Press “ENT“ and use UP or DOWN arrow buttons to
navigate to the following screen:
3. Press “ENT“ to enter Delete Partition Menu and you
shall see the following:
Disc Makers 1.12
3. Image
Image
4. Delete Partition
Choose Partition
[FUN ] DVD
tReflex Duplicator Manual
- 28 -
4. Use UP or DOWN arrow button to find the desired
partition and then press “ENT“ to submit your
selection and you shall see the following:
5. Press “ENT“ to confirm and you shall see the following
for 2 seconds.
7. Then, you will be directed back to Hard Drive Setup
Menu.
NOTES
I
mage
4. Delete Partition
D
elete Partition
[FUN ] DVD, OK?
P
artition [FUN ]
Deleted!

tReflex Duplicator Manual
- 29 -
Tutorial Guide:
Tutorial Guide
VIII. Change the SETUP settings
Most of the internal settings and information is stored inside
the SETUP menu. To explore and modify them is simple.
Below is an example to modify the “Auto Start“ setting.
Please note that the default setup is set for optimal
performance of the duplicator, it is unnecessary to change if
you are satisfied with the outcome.
1. Use UP or DOWN arrow button to navigate to the
following screen.
2. Press “ENT“ and use the UP or DOWN arrow buttons
to navigate to the following screen:
3. Press “ENT“ to enter Auto Start Setting Menu and you
shall see the following:
4. Use UP or DOWN arrow button to modify the setting to
“Full“ and then press “ENT“ to submit your selection
and you shall see the following:
DISCMAKERS 1.12
5.Setup
Setup
10. Auto Start
A
uto Start
A
uto
tReflex Duplicator Manual
- 30 -
5. If you would like to modify more settings, then please
go back to step 3. Otherwise, press “ESC“ button to
bring you back to main menu.
NOTES
S
etup
10. Auto Start
D
ISCMAKERS 1.12
5. Setup

tReflex Duplicator Manual
- 31 -
Tutorial Guide:
IX. Audio CD Editing
This process will guide you to perform the Audio Track
Selection feature. This process will help you combine audio
tracks from various CDs into a single customized audio CD.
In order for the duplicator to do all those things, you need a
temporary storage location to hold your songs before the
duplicator can make it an audio CD. The following are the
choices you will have:
•Hard Drive (if a Hard Drive is Installed):
By choosing “Hard Drive“ as the temporary storage
location, you will be instructed to load all of your
favorite songs into the Hard Drive and after you have
selected all of your favorite songs, you will be
instructed to copy them onto a blank 80 min CD-R
media.
•Blank CD-R media:
By choosing “Blank CD-R“ as the temporary storage
location, you will be instructed to copy all of your
favorite songs into the blank CD-R youíve inserted
and after you have finished, you will be instructed to
finalize the CD-R disc.
When you turn on your duplicator, after it has booted up, you
will see the following screen:
DISCMAKERS 1.12
1. COPY
tReflex Duplicator Manual
- 32 -
1. Going to the “Edit Audio Track“ menu
Use the UP or DOWN arrow button to navigate to the
following screen and press “ENT“.
2. If your duplicator does not have a Hard Drive installed, skip
to Step 5. However, if your duplicator does have a Hard
Drive installed, you will see the following:
At this point, you can press UP or DOWN arrow button to
select how you want to mix your audio tracks
Below are your options:
•Hard Drive(if a Hard Drive is Installed):
By choosing “Hard Drive“ as the temporary storage
location, you will be instructed to load all of your
favorite songs into the Hard Drive and after you have
selected all of your favorite songs, you will be
instructed to copy them onto a blank 80 min CD-R
media.
•Blank CD-R media:
By choosing “Blank CD-R“ as the temporary storage
location, you will be instructed to copy all of your
favorite songs into the blank CD-R youíve inserted
and after you have finished, you will be instructed to
finalize the CD-R disc.
D
ISCMAKERS 1.12
4. Audio
E
dit Audio Tracks
Edit to Blank CD

tReflex Duplicator Manual
- 33 -
3. Once you made your selection, you shall see the following:
OR
When you see above, please insert an audio CD that
contains your favorite track(s) in the Master Reading Tray
and a blank CD-R media into one of Writer Trays.
If either one of the ABOVE 2 screens is shown for
more than 2 minutes, please check your Master
Disc or Blank Discs for quality.
Please allow 5-10 seconds for the duplicator to detect your
Master Disc and Blank Discs as well. After your Master Disc
and Blank Discs have been recognized, then you shall see
the following screen:
When you see above, you can press UP or DOWN arrow
button to display the information on each track of this audio
CD and press “ENT“ to select the track to be copied. Once
a track is selected, you shall see “*“ on the left of the track
number on the 2nd line. You will also be able to see the
total tracks and total playtime you have selected. Once you
have finished selecting the tracks you want to copy, you can
press UP or DOWN arrow button until you see “ARE YOU
DONE?“ on the 2nd line like screen following:
Preparing...
W
aiting for a Blank
Preparing...
W
aiting for Master
Total: 0 Trk 0m: 0s
Track 1: 4m:31s
tReflex Duplicator Manual
- 34 -
You can press “ENT“ button to submit your selection. You
will see the following:
If the capacity of total audio tracks you have
selected is more than your blank CD-R discís
capacity, you shall see the following two screens
flashing:
If you see messages above, please press “ENT“ button to
continue.
Once the Copying process is complete, you shall see the
following screen:
At this point, you have a choice to finalize it (mark the completion)
or insert another audio CD for more songs.
OVER BLANK DISC CAPA
Press OK to Continue
T
otal 6 Trk 26m:17s
A
re you done?
A
udio Editing 1
2% 09:19
BLANK DISC CAPACITY
Press OK to Continue
T
otal 6 Trk 26m:17s
Finish Editing? >
“1” indicates that it is working on track #1.
“09:19” indicates that the track’s playback time.

tReflex Duplicator Manual
- 35 -
If you choose to insert another audio CD for more songs, you
need to press DOWN arrow button until you see the following
screen:
Then, press “ENT“ button to continue. After that, your old master
disc will be ejected and you can insert another audio CD into the
Reading Tray. Please go back and follow the instruction on Step 3.
If you choose to finalize it, you need to press the DOWN arrow
button until you see the following screen:
Then, press “ENT“ button to continue. You will see following
confirmation screen:
Press “ENT“ button again to confirm the finalization; it will copy
all tracks to the blank CD-R media you have inserted and finalize
it at the end. During the process, you shall see following progress
indicator:
Total 6 Trk 26m:17s
Confirm to Finalize?
Total 6 Trk 26m:17s
Finish Editing? >
A
udio Editing… 2
Insert Next Master?>
Finalizing...
Please Wait
tReflex Duplicator Manual
- 36 -
When the whole process completes, your mixed copy will be
ejected and you shall see the following:
Press ENT to return to the main menu:
NOTES
J
ob Completed!
Press OK to Finish
D
ISCMAKERS 1.12
4. Audio

tReflex Duplicator Manual
- 37 -
Example of Editing Audio Tracks to Hard Drive
(For Duplicators with Hard Drive Installed):
We need to create a new Audio CD from 2 different Discs.
CD1: song 2, and song 4
CD2: song 3, song 4 and song 5
1. Go to function 11. Edit Audio Track
2. Press “ENT“ button.
3. Use UP or DOWN arrow button to select “HDD“. Then press
“ENT“ button.
4. Insert CD1 into the Master Reading Tray and a blank to Writer
Tray 1.
5. Wait until the following screen appears.
6. Use the UP or DOWN arrow button until you see “Track 2“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 2“ like following:
Total: 0 Trk 0m:
0
0s
Track 1: 4m:03s
DISCMAKERS 1.12
4.Audio
Edit Audio Tracks
Edit to Blank CD
Edit Audio Tracks
Edit to HDD
tReflex Duplicator Manual
- 38 -
7. Use the UP or DOWN arrow button until you see “Track 4“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 4“ like following:
8. Use the UP or DOWN arrow button until you see following:
9. Press “ENT“ Once you submit your selection, you shall see
the following:
10. Once the loading process is complete, you shall see the
following screen:
11. Since you have not done with your selections yet, you need to
press DOWN button once and you shall see following:
12. Press “ENT“ button to continue and insert CD2 into the
T
otal: 2 Trk 9m:47s
Insert Next Master?
T
otal: 2 Trk 9m:47s
*Track 4: 4m:58s
T
otal: 1 Trk 4m:49s
*Track 2: 4m:49s
A
udio Editing... 2
3
% 04:58
T
otal: 2 Trk 9m:47s
A
re you done?
A
udio Editing... 2
Finish Editing? >

tReflex Duplicator Manual
- 39 -
reader tray. When CD2 is inserted, wait until the following
screen appears.
13. Use the UP or DOWN arrow button until you see “Track 3“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 3“ like following:
14. Use the UP or DOWN arrow button until you see “Track 4“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 4“ like following:
15. Use the UP or DOWN arrow button until you see “Track 5“ on
the 2nd line, and then press “ENT“ to confirm. A “*“ symbol
will appear on the left of “Track 5“ like following:
16. Use the UP or DOWN arrow button until you see following:
17. Press “ENT“ Once you submit your selection, you shall see
the following:
Total: 5 Trk 24m:29s
A
re you done?
Total: 5 Trk 24m:29s
*Track 5: 4m:27s
Total: 4 Trk 20m:01s
*Track 4: 5m:26s
Total: 3 Trk 14m:35s
*Track 3: 4m:47s
Total: 2 Trk 9m:47s
Track 1: 4m:03s
tReflex Duplicator Manual
- 40 -
18. Once the loading process to the hard drive is complete, you
shall see following screen:
19. Since we have finished selecting all of our tracks. Press “ENT“
button to continue to finalize. You shall see the following
screen:
20. Press “ENT“ button again to confirm the finalization and you
shall see the following screen:
21. When the whole process completes, your mixed copy will be
ejected and you shall see the following:
Then, you will be directed back to the main menu:
A
udio Editing... 3
Confirm to Finalize?
A
udio Editing... 3
Finish Editing? >
J
ob Completed!
Press OK to Finish
A
udio Editing... 3
5% 04:47
C
opying… H 79M
0/3 10% 5M
D
ISCMAKERS 1.12
4.Audio