Discount Car Stereo BLU-C6 User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
BLU-C6
QUICK START MUSIC STREAMING KITINSTALLATIONGUIDE FOR C6 CORVETTE WITHOUT XM TUNER MODULE OR 6-DISC CHANGER
Created September 17, 2016
RevisedAugust 30, 2020

Introduction:
Many C6 owners will be pleased to know they can update the factory system to
support Bluetooth music streaming. 2009+ C6 includes option for Bluetooth
which is great for making calls, but not so great for streaming music
applications. The BLU-C6 music streaming kit works in vehicles with or without
factory installed Bluetooth hands-free module to allow users to stream music
from smartphone while on the road; however, this kit takes the place of XM or
external 6-CD changer in storage well. Purchase our A2D-C6 instead.
A Bluetooth wireless connection means no wires, clutter or complicated setup.
Simply pair Smartphone, Tablet, Kindle etc. and enjoy audio books, Apple music,
Pandora, Waze and other applications on the car system. This guide covers basic
install steps for the BLU-C6.
See Frequent Asked question at the end of this guide.
Installation : (To radio)
Radio removal required to access and connect module to radio connector/plug.
1. Unclip and remove ride control switch/blank plate at front edge of
center console lid. (Figure 1A)
2. Remove (2) 9/32” screws from under the removed blank plate. (Figure
1B)
3. Unclip and remove entire panel surrounding radio and including A/C
controls. (Figure 1C)
4. Remove (4) 9/32” screws securing radio and extract from dash.
(Figure 1D)
Fig. 1
5. Disconnect factory 12-pin plug (See Fig. 3) from radio
Note: If radio 12-pin connector has no plug, proceed to step 6
otherwise connect factory 12-pin plug to installation harness gray
connector (See Fig. 4)
Fig. 3
12-pin plug

Fig. 4
connector
6. Connect installation harness 12-pin plug (See Fig. 3) to radio 12-pin
connector
7. Ensure module dip-switches #3 and #8 are “ON” or down (See Fig. 5)
Fig. 5
8. Connect installation harness 22-pin Molex plug to module 22-pin Molex
connector (See Fig. 6)
Fig. 6
9. Connect/Tap installation harness yellow wire to +12V Battery
(constant) supply
10. Connect/Tap installation harness black wire to Ground.
11. Crimp red accessory wire to blue connector on fuse tap (See Fig.7)
After crimp pull wire to verify crimp integrity.
Fig. 7
fuse tap
12. Remove HTD Seat/WPR RLY (heated seat/wiper relay) fuse from fuse
box. (See alternate 12V accessory sources on next page). Accessory
supply ensures module turns “ON” only when vehicle is in operation.
13. Insert factory fuse from step 12 to empty fuse slot on fuse tap (See
Fig. 7)
14. Insert fuse tap to fuse box slot vacated in step 12
Noteworthy: If heated seat/wiper relay fuse is missing, fuse tap empty
slot remains empty. Turn ignition “ON” to verify module LED is flashing,
otherwise user voltmeter or test light to test fuse slot for power
and/or check crimp integrity as often times a bad crimp could result
in no power. Other possible sources for accessory supply are circled
below.

C6 fuse panel in passenger footwell
Alternate 12V accessory fuse box options include:
1. EXL DML (Exhaust Module)
2. WPR/WSW (Windshield Wiper/Washer)
We do not recommend connecting Accessory wire to 12V battery (always
on) supply.
Warning: Accessory supply may include noise from motors, sensors, modules
etc. If music streaming include noises (hum, whine etc.), please find an alternate
power supply location or add noise filter
15. Tuck and secure any extra wires away from moving parts and proceed
to “Pairing”
Pairing:
Pairing process varies among devices but basic steps are the same. This
process is done upon initial install and will not have to be repeated.
1. Turn Ignition and radio “ON”
LED inside module peephole will flash (pairing mode)
2. On audio device: Go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select Bluetooth and turn on.
4. Select Bluetooth settings
5. Tap Scan (Search) for devices .
6. Wait for Bluetooth device name to appear and select it (See Fig. 9),
LED inside peephole turns solid (paired) and confirmation tone is
heard.
Fig. 9

Optional Smart remote:
Smart remote is optional and not required for operation, however instead
juggling audio device while driving (which is outright dangerous), simply
mount to dashboard or steering wheel to perform the following functions:
1. Control music wirelessly
2. Activate VR commands (Google play)
3. Track up/down
4. Volume up/down
Pairing smart remote:
Smart Remote operation:
These functions apply to iOS7.0 and higher and Android 4.4 and higher.
Contents:

Test Operation:
1. Turn ignition and radio “ON”
2. Press “CD/AUX”or “XM1/2”button on radio
3. Launch Smartphone or tablet music streaming application.
4. Ensure phone volume is set to 75% or more and use radio volume
control button to set playback level.
Playlist and Track selection *NOT* possible from
radio. Use audio device built-in controls or optional
wireless remote to access and control audio files.
5. If correct operation is confirmed go ahead and reinstall the Radio.
Product feature comparison:
Use chart below to learn about our C6 offerings.
Features/Requirements
A2D-C6
BLU-C6
C6-HF
Retains/requires XM Tuner module
YES
NO
YES*
Audio input jack (Aux in)
NO
NO
YES*
USB charging port
NO
NO
YES
Supports Hands-free calls
NO
NO
YES
Supports music streaming
YES
YES
YES
Option to connect to radio (dash)
NO
YES
YES
Option to connect to 16-pin plug in rear
YES
NO
NO
Supports voice activation (e.g. Siri)
NO
NO
YES
Optional wireless remote control
YES
YES
NO
Controls music from radio buttons
NO
NO
NO
*Aux input or retain XM playback (if subscribed)
** USB port support charging only. Not for connecting thumb drive etc.
Frequent asked questions
1. What happens to XM subscription once this kit is installed?
XM subscription is lost upon installing this module. 6-disc CD changer
playback (if present) is also lost. To retain XM subscription or 6-disc
changer playback, purchase our A2D-C6instead.
2. I don’t know if vehicle has XM Tuner module. How can I find out without
ripping the car apart?
Turn radio “ON”, press “BAND” or “XM 1/2” button repeatedly as radio
cycles through AM/FM/XM1. If only AM/FM is displayed, vehicle does not
have XM Tuner Module.
3. Can the BLU-C6be used to make hands free calls?
NO; the BLU-C6 does NOT support Hands-Fee calls. See our C6-HF
4. Why do I have to locate a +12V accessory wire for this kit?
Because there is no 12V accessory supply on radio 12-pin connector and
accessory supply is required so that module pairs/unpairs upon
entering/exiting vehicle.
5. Will I be able to control Bluetooth module from radio buttons?
NO; radio buttons do NOT control the BLU-C6. You must use audio device
built-in control to access and display song information, or purchase
optional remote control. Use radio volume button to set playback level.
6. My vehicle has a Navigation radio and 6-disc changer in storage well.
Will the A2D-C6 work?
YES, but the 6-disc changer must be disconnected.
Disclaimer
• This product has no affiliation with GM.
• We’re not liable for misuse of this product.
•We recommend professional installation.
Email [e-mail]
© 1995-Aug-20 Discount Car Stereo, Inc. All rights reserved.Informationin this document is subject to
change without notice. Other products and companies referred to herein are trademarks or registered
trademarks of their respective companies or mark holders.