Discount Car Stereo A2DIY-STS User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2DIY-STS
QUICK START BLUETOOTH MODULE INSTALLATION GUIDE FOR 2005-11 CADILLCAC STS WITH XM MODULE (U2K)
Created November 19, 2019
Revised: February 26, 2022

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This document is provided as a GENERAL installation guide, some vehicles vary and may
require additional steps. We do not accept responsibility for third party labor charges or
modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements
XM module with or without subscription
Introduction
2005-11 Cadillac STS owners eager to bring their smartphones and other digital
media devices on the road will be pleased with our A2DIY-STS Bluetooth module.
This module works with virtually all Bluetooth phones and sounds great for (1)
Mobile conversations, (2) music streaming and more. If XM subscription is
current, this module retains subscription, if expired; an AUX input jack is
provided to which users may connect and play portable audio devices (e.g., MP3
player, iPod, etc.) The included remote control allows tack up/down; adjust
volume on smartphone and to also useful when switching between sources.
Keep radio, car and XM subscription while enjoying Bluetooth features only
available on newer cars.
Warning: Vehicle must have an XM module with or without subscription. If
subscribed, the service remains operational, if not subscribed an AUX input jack
is provided instead. (See product page for details
Note: XM module is not built-into the AM/FM radio but rather a metal box in
remote area.
Frequently Asked question at the end of this guide for more details
Installation
Radio removal required to gain access to the connectors.
1. Using a panel removal tool, unclip and remove the top A/C vents panel
(See Fig. 1)
Fig. 1
2. Remove 10mm crews securing radio to dash (See Fig. 2)
Fig. 2
3. Pull radio forward to reveal connectors (See Fig. 3)

Fig. 3
Radio 16-pin connector
4. Disconnect factory 16-pin XM plug (See Fig. 4) from radio (See Fig. 3).
To disconnect, pull back BLUE locking tab, press BLACK tab, gasp and
pull plug from radio. (See Fig. 4)
Fig. 4
16-pin plug
Warning:To avoid connecting errors, all 16-pin connectors are “keyed”.
The 16-pin plug (See Fig. 4) included in this kit is “Keyed” and will only fit
the radio XM port (See Fig. 3)
Avoid pulling on wired. Grasp plug to remove.
5. Connect factory 16-pin plug to harness 16-pin connector (See Fig. 5)
Fig. 5
16-pin connector
6. Connect harness 16-pin plug to radio chamber vacated in step 4
7. Secure BLACK (ground) wire to vehicle chassis or remove radio
chassis screw and secure ground wire to radio as seen in Fig. 6
Fig. 6
Warning for vehicles with Bose amplifier: The radio provides module
with 12V accessory power. If vehicle has a Bose amplifier; the radio does
not supply enough current to power module and turn on factory amp.
(Module play will be distorted or intermittent). If this should happen
please disconnect red wire from harness, connect to extension cable
included in kit (See Fig. 7) then connect extension to alternate 12V
accessory source in vehicle (e.g. Fuse box, cigar lighter etc.)

Fig. 7
8. Locate 12V accessory at vehicles cigar lighter, fuse box, ignition cluster
etc.)
Warning: Extension (Fig. 7) must be connected to a
switched/accessory supply source, not constant battery supply.
Vehicles with Active XM subscription go to step 11
9. Connect supplied 3.5mm audio cable (See Fig. 8) to module “AUX” jack
(See Fig. 9). Route other end to front of the dash or wherever Aux
device will reside (within 3 ft.)
Fig. 8
Aux cable
Fig.9
Module
10. Install microphone (See Fig. 10) to vehicles visor or headliner using
included visor clip (See Fig. 11).
Fig. 10
Microphone
Fig. 11
Visor clip
11. Carefully route microphone wire down side pillar and behind dash into
radio cavity.
12. Connect microphone plug module “MIC” input (See Fig. 9)
Exercise caution when routing microphone so to not damage the cable
and ensure no ventilation ducts are pointed towards microphone.

Optional “Fast charge” kit
Optional charging kit can be added to support BC1.2, QC2.0, QC3.0, PE1.1, PE2.0,
FCP, SFCP fast charge protocols (Samsung, Huawei etc.).
Features:
» Input voltage: 6-24V DC
» Working current: 30mA
» Default output voltage: 5V or 3V-12V (device dependent)
» Max output power: 24W
Please Note: iPhone "Fast charge" kicks in when battery capacity is between
0-79%, and returns to regular charge mode when it reaches 80%.
Should you decide on this option; we suggest one of 2 connecting options:
A. Flush to dash/panel requires drilling a ¾” hole
B. Flush with support bracket (Mount USB terminal wherever your installation
demands without drilling)
A. Flush to Dash or Panel (drilling required)
1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent
(See Fig. 12)
Fig. 12
Step drill bit
2. Insert supplied 3ft. USB male terminal (See Fig. 13) through hole
created in step 1 and connect to charging port (See Fig. 14)
Fig. 13
Fig. 14
USB port
3. Snap USB head (See Fig. 15) in place and flush with mounting surface
(See Fig. 16)
Fig. 15
USB head

Fig. 16
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and test operation
B. Bracket Mount (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. of module and
mount USB support bracket (See Fig. 17) to surface using
adhesive/tape or screws (included).
Fig. 17
USB mounting bracket
2. Insert male terminal through hole in bracket (See Fig. 18) and connect
to module USB port (See Fig. 14)
Fig. 18
3. Snap USB head (See Fig. 18) to bracket until flush (See Fig. 19)
Fig. 19
4. Connect/tap YELLOW wire to accessory or battery supply. Your choice!
Accessory connection: charging is possible with ignition/engine “ON”.
Battery connection: charging is possible at all times.
Verify BLUE LED is lit.
5. Tuck and secure any extra wire away from moving parts and test operation
( See Bluetooth Pairing and Connection )

Bluetooth remote control
Pairing: Ensure Bluetooth is enabled on your device (e.g., Smartphone/Tablet
etc.)
Press and hold pause/play until Blue LED begin flashing
Scan smartphone for available devices and select BT009 from list. (Blue LED
turns off).
Installing:
Attach the button to steering wheel (includes holder) or attach to dashboard
using included double-sided tape –your choice.
Because the media button pairs with your Smart device, it can also be used at
home, in the park or wherever you decide to play your tunes.
Operation:
Once paired to smart device (e.g., Phone, Tablet, etc.), users may perform the
following functions on iOS with Bluetooth 3.0 and later or Android 4.0 or later.
The media button function applies to smartphone NOT the Jaguar radio.
Charging:
Media remote button built-in rechargeable 200mAH battery may last up to 10
days. Connect included USB cable to charge charging port at the back.
Red LED indicates charging; A full charge is reached after 2 hours at which time
LED turns off.

Module Pairing
Pairing varies among devices but basic steps are the same. This process is done
upon initial install and will not have to be repeated.
1. Turn ignition and radio “ON”
LED inside module will flash rapidly (pairing mode)
2. On A2DP device: go to Bluetooth Settings
3. Select Bluetooth and enable it
4. Tap Scan for devices .
5. Wait for Bluetooth device name (See Fig. 20) to appear and tap it. Once
paired confirmation tone is heard on car speakers
Fig. 20
Warning:Caller ID, ID3 tags etc., are not shown on radio display. Operate
Bluetooth device via wireless remote control, VR (voice recognition) or
smartphone built-in controls. Radio buttons can be used to adjust playback
level
Operation
1. Turn ignition and radio “ON”
2. Press “BAND” or “XM” button on radio.
3. Launch Smartphone or tablet music streaming application
4. Ensure audio device volume is set to 80% or more.
5. Place call. Press Pause/Play to answer/end call.
6. If correct operation is confirmed go ahead and reinstall radio.
If successful go ahead and reinstall radio

Frequent ask questions & troubleshooting
1. Don’t all STS radios have built-in XM tuners?
NO! Unlike AM/FM tuners, the XM tuner module is not bult-into the radio.
XM module is a metal box (See Fig. 21) installed in remote location (trunk,
hatch, glovebox area etc.) and connects to the AM/FM radio via a 16-pin
harness. For the A2DIY-STS to work, vehicle must have module pictured in
Fig. 22 below. See question #5.
Fig. 21
2. Will the A2DIY-STS work in vehicles with Navigation?
YES; works in both Navigation and non-navigation radios with XM module
seen in Fig. 21
3. My XM subscription has long expired, will the A2DIY-STS still work?
YES; as long as XM module remain in vehicle.
4. My XM subscription is active. Will it be lost after installing the A2DIY-
STS?
NO, this module retains XM subscription. Select “Subscribed”. If
subscription has expired; an AUX input jack is provided.
NOTE: If not currently subscribed but plan to renew at a future date,
select “Subscribed”otherwise XM will not play through upon renewal.
5. I’m not the original vehicle owner and don’t know if it has an XM
module. How can I verify vehicle has required XM module?
Turn radio “ON”, press “BAND” button repeatedly to cycle through
AM/FM/CD/XM. If only AM/FM/CD is displayed, vehicle is NOT
compatible. Navigation radios: if XM softkey is “grayed out”, vehicle
does not have XM tuner and not compatible with this part.
6. My STS has factory Hands-free kit but does not support streaming. Is
there something you offer to add streaming?
YES; purchase our A2D-STS to add music streaming to factory system.
The A2D-STS will not interfere with factory hands-free kit. Pair smart
device to both modules.
7. Can I use steering wheel or radio buttons to control music playback?
NO; you must use included media button or Smartphone built-in controls
and display for access/controls.
8. Do I have to pair smartphone to module in order to listen to XM or AUX?
NO, XM or AUX playback is possible without paring phone. Simply place radio
in XM mode (press BAND button) and XM (if subscribed) or AUX device will
play. To stream music or initiate/receive Bluetooth calls, smartphone must
be paired to module and radio must be in XM mode.
9. My module connects and pairs, but playback is distorted, low or
intermittent. What can be done to remedy this?
This is possible in vehicles with Bose amplifiers where the radio does not
provide enough current to turn on amplifier and power module. In these
situations use extension wire included in kit to power module from alternate
power source (go to page 3)
Disclaimer
• This product has no affiliation with GM
• We’re not liable for misuse of this product.
•We recommend professional installation
Email [e-mail]
© 1995-Feb-22 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.