Displays2go CFSTN2B User manual

Stand Instructions
CFSTN2B

Table of Contents
Table of Contents and Warnings
Part List
Assembly and Installation
1. Adjust upper and lower poles
2. Attaching to the base assembly
3. Install steel cross rods
4. Install AV Shelf
5. Install the TV
6. Install mount to frame
2
3
4
5
6
7
8
9
Tools Required
Phillips Screwdriver
Tape Measure
Wrench
WARNING!
Severe personal injury and property damage can result from improper installation.
Read instructions carefully before beginning.
Assistance is required when installing the TV.
If you do not understand the instructions or have any concerns please contact a
qualified local installer.
Do not install or assemble if the product or hardware is damaged or missing, if you
require replacement parts, contact your local dealer.
This product fits most 40” - 60” flat panel displays; maximum eight for the disply is 100 lbs.
Do not use this product for anything other than what it was originally designed.
This product contains moving parts, please use caution.
The manufacturer disclaims any liability for the modifications, improper installation, and
installation exceeding maxium weight capacity. The manufacturer will not be liable for any
damages arising out of the use of, or inability to use the product.
Tighten Loosen Adjustment
Phillips
Screwdriver
Tape
Measure
Visual Guides
By Hand Hex Wrench
Assistance
Required
7. Webcam shelf installation 10
8. Adjusting the mount 11

8
10
4
5
DE
0
5
GHI
A1x1
A2x4 A3x1
B3x1
C1x1 C2x2
J
15
K
25
B2x2
B4x4
8
C3x2
E1x1
E2x1
B1x1
D1x1 D2x1 D3x1 D4x2
50
6
1.2
Φ12 6.3
NML

1
1
3
2
Adjust upper and lower poles
Locate the spring plungers inside the bottom grommet hole of pole
B1 (If your unit has B3 cross bar pre-installed remove prior). Starting
with the right side pole B2, push the spring plunger down and pull
B2 up slightly and twist it slightly so that the spring plunger remains
Repeat the same steps for the left side pole B2 but use your
right foot for stability instead. Align poles B2 and lock the spring
Hold the poles B1 & B2 with your hands and use your left foot on
the cross bridge of B1 for stability. Pull B2 upward until you reach
your desired height. Twist B2 so that the spring plunger locks into
B1
B1
B1
B2 B2
B2 B2
Spring
plunger
Spring
plunger
Lift pole assembly so that the part remains upright and the
cable management holes are facing toward you.

2
1
2
3
2
1
3
Attaching to the base assembly
Thread casters A2 into the bottom of base A1. Make sure all casters a
re locked to prevent movement during installation.
With allen wrench M attach lower poles B1 to base A1 with screw G.
First through the bottom of base A1, then through the top of base A.
After screws GA3
until it locks into place.
Lock Casters
before assembly
G
G
A1
B1
H
A2
A2 A2
A2 A3
B1
A1
Tighten Fully
with wrench
cable management
holes facing back

3
3a
Install steel cross rods
Height adjustment
12
3
Remove the pre-installed
screws on rod B3. Making
sure the upper poles B2
are aligned, slide rods B3
into the top openings.
Slide the upper poles B2 up or down
to the different spring plunger holes for
your desired height. Install grommet
covers B4 into the grommet holes.
Press and hold both spring
plungers to slide the upper
poles B2.
Refasten rods B3
with screws.
Phillips
screwdriver
B3
B3
B3
B3
B2
B4
B4
B4
B4
H / 1050mm - 1500mm
Assistance
Required
Cables
Unplugged

LH
M
22
D2
D3
D4 D4
D1
AV shelf assembly and installation
4

5
5a
DE
B, C
VESA: 200x200mm
Phillips
screwdriver
5b
Install the TV
Spacer Suggestions
E
D
(B, C)+D,A
D
J
C2
C1
K
Slider plate
Remove pre-installed screws
C3

6Install mount to frame
Make su re casters
are locked prior to
installation
Attach hooks on C1
onto cross rods B5
Secu re lock hook fully
Lock not included
Lift up lock hook
before installing
mount
Heavy Lifting:
Assistance
Requi red
C1
1
3 4
2
C1
B5
I

E1 E2
7Webcam shelf installation
Adjustable height
M
N
Phillips
screwdriver