Displays2go MNTW803L User manual

Item No.:MNTW803L
Maximum Weight Capacity: 30kg/66lbs
Adjustableangle: 5 15
IntegratedCablemanagement
"～"
-～° °
This productwasdesigned to be installedonwoodstudwallsandsolidconcrete walls.
Before installingmake sure thesupportingsurfacewillsupportthecombinedload of the
equipmentandhardware. NeverexceedtheMaximum LoadCapacity.This product is
intendedforindooruseonly. Use of this productoutdoorscouldlead to productfailure or
personalinjury.
CAUTION
INSTALLATION GUIDE
-8-
This productcontainssmallitemsthatcould beachokinghazard if swallowed.Keep
theseitemsaway from youngchildren
1.Make sure theseinstructions are readandcompletelyunderstoodbefore attempting
installation. If you are unsure of anypartofthisinstallation,contactaprofessional
installerforassistance.
2.The wall or mountingsurfacemust be capable of supportingthecombinedweight of
themountandthedisplay; otherwisethestructure must be reinforced
3.Safetygearand propertoolsmust be used.Aminimum of twopeople are required
forthisinstallation. Failure to usesafetygearcan result in propertydamage,serious
injury or death.
!
.
Warning
Thankyouforchoosingour product
180°
-5~15° °
Cablemanagementclip
Cable routingaccesspoints
Tensionscrew
Wrench(J)
180°
23 50

-2-
Hardware Kit:
Hardware Kit:
-7-
TV Plate
Qty Description
A
B
D
C
E
F
G
4
4
4
4
2
4
2
M4x12mm bolt
M5x12mm bolt
M6x12mm bolt
M5 Washer
ID
Long bolt
Concrete anchor
A-D FHI
E
M6 Washer
J
H
1Allen wrench
Part 5-Adjusting display and using cord management
Route cords along articulating arms using cord management .
Articulating arms can be adjusted to position display into desired location.
Use allen wrench (J) to tighten and loosen the tension screw. Do not
overtighten and do not loosen to the point the screws come out.
clip
Part 5-Adjusting display and using cord management
Wall Plate
Plastic cover
I
J
4M8x12mm bolt
4M8 Washer
G
Part 4-Attaching plastic covers to wall plate
Secure plastic covers over wall plate by pushing them toward each other
until they lock in place.
Part 4-Attaching plastic covers to wall plate
TV
Nut Adaptor

-3-
A-D
E,F,G
Washer(E, F or G)
E
F
.
Part 1-Attaching TV Plate To Screen
Center TV plate vertically on back of screen. Select the small(A), medium
(B or C) or large(D) screws. Attach TV plate to screen using four selected
screws and four washers(E, ).For G Tighten screws firmly. Do not overtighten
Part 1-Attaching TV Plate To Screen
Medium hole for
M6 screws
Small hole for
M4 screwsand M5
G
Medium hole for
M8 screws
Concrete Wall 2”(50mm)
Φ3/8”(10mm)
TV
-6-
Part 3b-Concrete Wall Mounting
Level wall plate and use wall as a template to mark two holes. Drill two 3/8
(10mm) dia. holes 2 (50mm) deep. Insert anchors(I) into holes and put
screws(H) without tightening, hang the TV bracket onto the screw, and then
tighten the screw firmly.Do not overtighten.
”
”
Part 3b-Concrete Wall Mounting
H
I
H

-4-
-5-
Stud finder
2 (50mm)”
3/16 (5mm)”
Wood stud
TV
.
Part 2-Attaching adaptor to TV plate
If using VESA 400X400 mounting patterns, which screws will be attached
to the screen. Attach adaptor to TV plate using four nuts. Tighten screws
firmly. Do not overtighten
Part 2-Attaching adaptor to TV plate
Nut
Adaptor
Part 3a-Wood Stud Mounting
.
Use wall plate as a template, make sure it is level, and mark mounting
holes along the center line of the wood stud. Drill two
.
two
3/16 (5mm) dia Holes
2 (50mm) deep. Put screw (H) into the hole without tightening, hang the TV
bracket onto the screw, and then tighten the screw firmly.Do not overtighten
”
”
Part 3a-Wood Stud Mounting
H
H