Displays2go TVSTNDLBK2 User manual

Nby!Mpbe;!261!mct!qfs!tdsffo
Nby!Mpbe;!
22!mct
8ZMTWP/`LW>N]PPY?A>_LYO
,^^PXMWd4Y^_]`N_TZY^
>6@^%?A>?9/7-6?A>?9/7>A
4QdZ`SLaPLYd\`P^_TZY^]PRL]OTYRZ`][]ZO`N_^[WPL^PaT^T_`^L_bbbOT^[WLd^RZNZX
Z]NZY_LN_/2N`^_ZXP]^P]aTNPL_###
>NLY<=NZOP_Z
aT^T_[]ZO`N_[LRP

D/
B/
M/
F/
Qbsu!Mjtu;
C/
Ø2 Ø3
Ø2
Ø2
E/
G/
Ø3 Ø5
H/
Ø2
I/
Ø2
J/
K/
Ø9 Ø5
L/
Ø3
Ø23 Ø35
P2/ P3/
O2/ O3/ O4/ O5/
Ø25Ø9 Ø25 Ø9
Ø5
N2/ N3/
Ø5
N4/
Ø3
N5Ø9 N9Ø25
N9Ø21
N9Ø27 N9
N9Ø25
N9Ø21 Ø5Ø2
Q3/Q2/
R2/ R3/ R4/
N7Ø27
N5 N6 N7
Ø23
N7Ø46 N9Ø27 N9Ø46 205# N9
Ø23
T2/ T3/ T4/ T5/ T6/ T7/
UW!Lju
UW!Lju
N5Ø27 N5Ø46 N6Ø27 N6Ø46 N6
S2/ S3/ S4/ S5/ S6/
Uppm!Sfrvjsfe
Ø2

M
B
2/
Ø5
R4
O3
O4
3/
C
Ø8
Ø8
Ø3
4/
R3
mpdl!uif!tdsfxt!bu!
eftjsfe!ifjhiu
F
5/
R4
N3
E
Jg!dsptt!cbs!epft!opu!
tmpu!fbtjmz-mpptfo
!uif!O3!boe!O4!tdsfxt!
bu!uif!cbtf!pg!uif!
wfsujdbm!cbs
Ø3
1. Attach casters to the bottom of the frame, using a wrench
to tighten.
2. Slot screw down through the leg posts as shown, and use
Allen wrench to tighten down. Repeat for both legs.
3. Slot cross bar into leg posts and then lock the screws by
tightening at desired height. Use a level to ensure it is straight.
4. Attach media shelf to cross bar as
shown. Tighten screws to lock shelf in
place.

6/
D
L
R4
Mpdl!uif!tdsfxt!bu!
eftjsfe!ifjhiu
Tmjhiumz!ujhiufo!
uif!tdsfxt!
mfbwjoh!uifn!
tmjhiumz!mpptf
7/
Ø7
P2
Ø3
Ø23
P3
R2
8/ Ø3
5. Insert handles into upper leg post pieces by sliding in as
shown, then tightening screws to lock in desired place.
6. Insert screws into prongs, then tigten slightly,
leaving slightly loose.
7. Insert prongs into lower leg post.

R2
Ø3
9/
Gbtufo!uif!
tdsfxt!
Mpdl!
uif!
tdsfxt!
bu!uif!
eftjsfe!
ifjhiu
G
Ø9
O5
:/
21/
R4
Ø3
N4
Ø5
Q3
R2 Q2
22/
Ø3
MFGU
SJHIU
Ø3
8. Tighten screws that
were left loose in step 6
to lock the posts together.
9. Lock the flat panel at
the desired height at
which you would like to fix
the crossbar that will hold
the TV.
10. Slide in locking mechanisms.
11. Slot cross bars that hold TV together and lock in
place with screws.

O2
R3
23/
Bee!tqbdfst!jg!
ofdfttbsz///
UW
Ø3
S2S5!pg!T2T5
T7
S6!pg!T6
H
24/ 25/
Ø5
Ø3
O5
12. Put TV crossbar onto flat panels and
lock in place from the back of the unit, as
shown. Repeat for both posts. A level is
recommendded.
13. Affix brackets onto back of TV, as shown.
14. Place bracket onto the TV crossbar by
fitting the notches over the bar.

Qbsu!K!jt!vtfe!
gps!dpse!
nbobhfnfou!dbo!
cf!dvu!up!
bekvtu!mfohui!
jg!ofdfttbsz
26/ 27/
28/ 29/
K
R4
N3
Ø3
J
N2
Ø5
N4
15. Fit rubber-tipped screw into bracket and tighten
to hold the bracket in place at desired angle.
15. Slot the plastic cord management unit into the leg
posts at desired height to hold TV cord.
17. Attach top media shelf to its support, as shown.
18. Attach the media shelf to the back of the
TV crossbar.