dixell iPro SERIES Instruction Manual

iPro SERIES (V.3.2)

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 3/72
INDEX
1.IMPORTANT RECOMMENDATIONS 5
1.1PRODUCT DISPOSAL (WEEE) 6
2.INTRODUCTION 7
3.GENERAL SPECIFICATIONS 8
3.1PROCESSING ENVIRONMENT 8
3.1.1Fields of application................................................................................................................................................................ 8
3.1.2Hardware architecture ............................................................................................................................................................ 8
4.VERSIONS OF THE PROGRAMMABLE CONTROLLERS 10
4.1IPRO.GENIUS AND IPRO.CHILL (IPG100D – IPC100D RANGES) 11
4.1.1Description of the connections ............................................................................................................................................. 12
4.1.2Description of the inputs and outputs ................................................................................................................................... 13
4.1.3Technical specifications ....................................................................................................................................................... 16
4.1.3.1Analogue inputs........................................................................................................................................................... 16
4.1.3.2Digital inputs................................................................................................................................................................ 16
4.1.3.3Analogue outputs ........................................................................................................................................................ 16
4.1.3.4Standard Digital outputs .............................................................................................................................................. 17
4.1.3.5SSR Digital outputs version......................................................................................................................................... 17
4.1.3.6Wiring diagrams .......................................................................................................................................................... 18
4.1.3.7Mechanical specifications............................................................................................................................................ 19
4.1.3.8Electrical specifications ............................................................................................................................................... 19
4.1.3.9Plastic container .......................................................................................................................................................... 19
4.1.3.10Product certifications ................................................................................................................................................... 19
4.2IPRO.GENIUS (IPG200D RANGE) 20
4.2.1Description of the connections ............................................................................................................................................. 21
4.2.2Description of the inputs and outputs ................................................................................................................................... 22
4.2.3Technical specifications ....................................................................................................................................................... 24
4.2.3.1Analogue inputs........................................................................................................................................................... 24
4.2.3.2Digital inputs................................................................................................................................................................ 24
4.2.3.3Analogue outputs ........................................................................................................................................................ 24
4.2.3.4Digital outputs.............................................................................................................................................................. 24
4.2.3.5Wiring diagrams .......................................................................................................................................................... 25
4.2.3.6Mechanical specifications............................................................................................................................................ 25
4.2.3.7Electrical specifications ............................................................................................................................................... 25
4.2.3.8Plastic container .......................................................................................................................................................... 26
4.2.3.9Product certifications ................................................................................................................................................... 26
4.3IPRO 4 DIN (IPG100D – IPG200D – IPC100E RANGES) 27
4.3.1Description of the connections ............................................................................................................................................. 27
4.3.2Description of the inputs and outputs ................................................................................................................................... 28
4.3.3Technical specifications ....................................................................................................................................................... 29
4.3.3.1Analogue inputs........................................................................................................................................................... 29
4.3.3.2Digital inputs................................................................................................................................................................ 29
4.3.3.3Analogue outputs ........................................................................................................................................................ 30
4.3.3.4Digital outputs.............................................................................................................................................................. 30
4.3.3.5Wiring diagrams .......................................................................................................................................................... 30
4.3.3.6Mechanical specifications............................................................................................................................................ 31
4.3.3.7Electrical specifications ............................................................................................................................................... 31
4.3.3.8Plastic container .......................................................................................................................................................... 31
4.3.3.9USB-ETHERNET Adapter........................................................................................................................................... 31
4.4IPRO.LINK (IPL500D) 32
4.4.1Description of the connections ............................................................................................................................................. 32
4.4.2Description of the inputs and outputs ................................................................................................................................... 33
4.4.3Technical specifications ....................................................................................................................................................... 33
4.4.3.1Wiring diagrams .......................................................................................................................................................... 33
4.4.3.2Mechanical specifications............................................................................................................................................ 34
4.4.3.3Electrical specifications ............................................................................................................................................... 34
4.4.3.4Plastic container .......................................................................................................................................................... 34
4.5IPX106D 35
4.5.1Description of the connections ............................................................................................................................................. 35
4.5.2Description of the inputs and outputs ................................................................................................................................... 36
4.5.3Technical specifications ....................................................................................................................................................... 37
4.5.3.1Analogue inputs........................................................................................................................................................... 37
4.5.3.2Digital inputs................................................................................................................................................................ 37
4.5.3.3Analogue outputs ........................................................................................................................................................ 37
4.5.3.4Digital outputs.............................................................................................................................................................. 37
4.5.3.5Wiring diagrams .......................................................................................................................................................... 38
4.5.3.6Mechanical specifications............................................................................................................................................ 38
4.5.3.7Electrical specifications ............................................................................................................................................... 38

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 4/72
4.5.3.8Plastic container .......................................................................................................................................................... 39
4.5.3.9Setting the address of the device ................................................................................................................................ 39
4.6IPX125D – IPX115D 40
4.6.1Description of the connections ............................................................................................................................................. 40
4.6.2Description of the inputs and outputs ................................................................................................................................... 41
4.6.3Technical specifications ....................................................................................................................................................... 43
4.6.3.1Analogue inputs........................................................................................................................................................... 43
4.6.3.2Digital inputs................................................................................................................................................................ 43
4.6.3.3Analogue outputs ........................................................................................................................................................ 43
4.6.3.4Digital outputs.............................................................................................................................................................. 44
4.6.3.5Wiring diagrams .......................................................................................................................................................... 44
4.6.3.6Mechanical specifications............................................................................................................................................ 45
4.6.3.7Electrical specifications ............................................................................................................................................... 45
4.6.3.8Plastic container .......................................................................................................................................................... 45
4.6.3.9Setting the address of the device ................................................................................................................................ 45
4.7IPX225D – IPX215D 46
4.7.1Description of the connections ............................................................................................................................................. 46
4.7.2Description of the inputs and outputs ................................................................................................................................... 47
4.7.3Technical specifications ....................................................................................................................................................... 49
4.7.3.1Analogue inputs........................................................................................................................................................... 49
4.7.3.2Digital inputs................................................................................................................................................................ 49
4.7.3.3Analogue outputs ........................................................................................................................................................ 49
4.7.3.4Digital outputs.............................................................................................................................................................. 50
4.7.3.5Wiring diagrams .......................................................................................................................................................... 50
4.7.3.6Mechanical specifications............................................................................................................................................ 51
4.7.3.7Electrical specifications ............................................................................................................................................... 51
4.7.3.8Plastic container .......................................................................................................................................................... 51
4.7.3.9Setting the address of the device ................................................................................................................................ 51
5.INTERFACE 52
5.1VISOGRAPH 52
5.1.1Specifications ....................................................................................................................................................................... 52
5.1.2Connections ......................................................................................................................................................................... 53
5.1.3Options menu ....................................................................................................................................................................... 53
5.1.4Dimensions........................................................................................................................................................................... 54
6.MEANING OF THE LEDS AND JUMPERS IN THE VARIOUS DEVICES 55
6.1PROGRAMMABLE CONTROLLERS 55
6.2EXPANSION MODULES 55
7.INSTALLATION 56
7.1GENERAL RULES 56
7.2POWER SUPPLY 56
7.3CONNECTION OF THE ANALOGUE INPUTS 57
7.3.1Temperature probes (NTC and PTC)................................................................................................................................... 57
7.3.2Pressure transducers and current probes (0 - 20mA, 4 - 20mA) ......................................................................................... 57
7.3.3Pressure transducers and ratiometric pressure transducers (0 - 5V)................................................................................... 58
7.3.4Live probes (0 - 1V, 0 - 5V, 0 - 10V)..................................................................................................................................... 58
7.3.5Probes and transducers with 24Vac/dc power supply.......................................................................................................... 59
7.4CONNECTION OF THE DIGITAL INPUTS 60
7.4.1Potential-free digital inputs ................................................................................................................................................... 60
7.4.2Live digital inputs (24Vac/dc) ............................................................................................................................................... 61
7.5CONNECTION OF THE ANALOGUE OUTPUTS 61
7.5.10 - 10V, 4 - 20mA Analogue output for condensation control .............................................................................................. 62
7.5.2PWM analogue output for condensation control .................................................................................................................. 63
7.5.30 - 10V, 4 - 20mA Proportional analogue output for servomotors/actuators ........................................................................ 63
7.5.4Devices with 24Vac/dc power supply ................................................................................................................................... 64
7.5.5Analogue output for relays (coil power supply 12Vdc) ......................................................................................................... 65
7.6CONNECTION OF THE DIGITAL OUTPUTS 65
7.7CANBUS CONNECTION 66
7.8RS485 SLAVE CONNECTIONS 67
7.9RS485 MASTER CONNECTION 68

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 5/72
1. IMPORTANT RECOMMENDATIONS
¾The symbol alerts the user of non-insulated “dangerous voltage” within the product area that
is sufficiently high to constitute a risk of electric shock to persons.
¾The symbol alerts the user of important operating and maintenance (assistance) instructions
found in the documentation attached to the device.
¾Dixell Srl cannot accept any liability for damages caused by modems that are not supported. Dixell
Srl reserves the right to modify this manual without prior notice. The documentation can be
downloaded from www.dixell.com even prior to purchase.
¾This manual forms part of the product and must always be kept near the device for easy and quick
reference. The device cannot be used as a safety device. Verify the limits of application before using
the device.
¾Verify that the power supply voltage is correct before connecting the device. Do not expose it to
water or humidity: use the controller only within the operating limits, avoiding sudden changes in
temperature and high atmospheric humidity in order to prevent condensation from forming.
Recommendation: disconnect all the electric connections before performing any maintenance. Insert
the probe where it cannot be reached by the End User. The device must not be opened. Consider
the maximum current that can be applied to each relay. Make sure that the wires for the probes, the
loads and the electrical power supply are separated and sufficiently distant from each other, without
crossing or intertwining with each other. In the case of applications in industrial environments, it may
be useful to use the main filters (our mod. FT1) in parallel to the inductive loads.
¾The customer shall bear full responsibility and risk for product configuration in order to achieve the
results pertaining to installation and/or final equipment/system. Upon the customer's request and
following a specific agreement, Dixell s.r.l. may be present during the start-up of the final
machine/application, as a consultant, however, under no circumstances can the company be held
responsible for the correct operation of the final equipment/system.
¾Since Dixell products form part of a very high level of technology, a
qualification/configuration/programming/commissioning stage is required to use them as best as
possible. Otherwise, these products may malfunction and Dixell cannot be held responsible. The
product must not be used in any way that differs from that stipulated in the documentation.
•The device must always be inserted inside an electrical panel that can only be accessed by
authorised personnel. For safety purposes, the keyboard must be the only part that can be reached.
•The device must never be hand-held while being used.
¾It is good practice to bear the following in mind for all Dixell products:
oPrevent the electronic circuits from getting wet as contact made with water, humidity or any
other type of liquid can damage them. Comply with the temperature and humidity limits
specified in the manual in order to store the product correctly.
oThe device must not be installed in particularly hot environments as high temperatures can
damage it (electronic circuits and/or plastic components forming part of the casing). Comply
with the temperature and humidity limits specified in the manual in order to store the product
correctly.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 6/72
oUnder no circumstances is the device to be opened - the user does not require the internal
components. Please contact qualified service personnel for any assistance.
oPrevent the device from being dropped, knocked or shaken as either can cause irreparable
damage.
oDo not clean the device with corrosive chemical products, solvents or aggressive detergents.
oThe device must not be used in applications that differ from that specified in the following
material.
¾Separate the power of the device from the rest of the electrical devices connected inside the
electrical panel. The secondary of the transformer must never be connected to the earth.
¾Dixell Srl reserves the right to change the composition of its products, even without notice,
ensuring the same and unchanged functionality."
1.1 PRODUCT DISPOSAL (WEEE)
With reference to Directive 2002/96/EC of the European Parliament and of the Council of 27 January
2003 and to the relative national legislation, please note that:
¾There lies the obligation not to dispose of electrical and electronic waste as municipal waste but to
separate the waste.
¾Public or private collection points must be used to dispose of the goods in accordance with local
laws. Furthermore, at the end of the product's life, it is also possible to return this to the retailer when
a new purchase is made.
¾This equipment may contain hazardous substances. Improper use or incorrect disposal can have
adverse effects on human health and the environment.
¾The symbol shown on the product or the package indicates that the product has been placed on the
market after 13 August 2005 and must be disposed of as separated waste.
¾Should the product be disposed of incorrectly, sanctions may be applied as stipulated in applicable
local regulations regarding waste disposal.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 7/72
2. INTRODUCTION
iPRO is the range of programmable controllers manufactured by Dixell.
The range consists of programmable controllers, I/O expansions, drivers for electronic valves and graphical
interfaces adapted to cover any type of application in the air-conditioning sector, cooling sector and any
relative area. As the system is one of the most technologically advanced, it is flexible and can be customised
for it to be adapted to the user’s particular requirements.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 8/72
3. GENERAL SPECIFICATIONS
The Dixell programmable controllers are all powered at 24Vac/dc and use a high speed performance 32-bit
ARM9 (200 MHz) microprocessor. The models differ in size (10 DIN or 4 DIN) and number of inputs and
outputs (analogue and digital).
One of the features that distinguishes the iPRO controllers is the vast range of connection options with
external devices, Dixell as well as other brands. CANBus, RS485 Master and Slave, and an Ethernet and
USB port provide maximum flexibility of integration with the outside world. MODBUS RTU protocol, one of
the most popular in the world, is used for serial communication.
Up to 80 MB of flash memory are entirely available to the user, according to the model. All the inputs and
outputs are fully configurable.
3.1 PROCESSING ENVIRONMENT
All Dixell programmable controllers use the following software as a processing environment:
¾ISaGRAF® to process the iPRO application.
¾VISOPROG to process the LCD graphic interface application (VISOGRAPH)
ISaGRAF® software is used worldwide and allows those with no programming experience to build
applications ranging from the simplest to the more sophisticated. The vast range of the most popular
programming languages (Structured Text, Function Block Diagram, Ladder Diagram, Instruction List,
Sequential Function Chart, Flow Chart, FBD IEC 61499) provides all programmers with access to the
processing environment. Thanks also to the extensive libraries of blocks already developed by Dixell, the
processing and debug times are reduced.
The SIMULATION (verification of the application without using the controller) and DEBUG options
(verification of the actual application within the controller), allow the user to block and force the value of the
variables to speed up the testing times.
3.1.1 Fields of application
The possibility of all-round configuration allows the Dixell iPRO programmable controller to be used for any
type of application. The same applications can be downloaded in the various models available (obviously
adapting the number of inputs and outputs).
The hardware has already been used for the following applications:
¾Chillers and heat pumps
¾Air treatment units
¾Air-conditioners
¾Roof-tops
¾Cooling systems
¾Energy saving management in systems
¾Climatic chamber control
¾Cold rooms and seasoner cabinets
3.1.2 Hardware architecture
The iPRO programmable controller is structured as follows:
•32-bit microprocessor used to run the application
•Removable connectors (Molex) or bayonet connectors (Phoenix)
•The programme and parameters are stored in a permanent flash memory. No data is lost in case of
power failure.
•Internal web server with the Dixell website as default with the option of downloading a customised
website for reading and writing variables with synoptic creation (via HTML).
•Ethernet port.
•USB port.
•Connection to the dedicated remote LCD display.
•CANBus.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 9/72
•RS485 Master.
•RS485 Slave.
The remote LCD display has the following features:
•240x96 pixel LCD graphic display.
•32-bit processor.
•Multilingual in ASCII or UNICODE version.
•8 fully programmable keys.
•Panel or wall mounted.
The LED display (only for the IPS versions) has the following features:
•Configurable digits and icons
•6 fully programmable keys

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 10/72
4. VERSIONS OF THE PROGRAMMABLE CONTROLLERS
10 DIN versions:
•IPRO.GENIUS
oIPG115D (15 relays, no application, disconnectable connectors)
oIPG215D (15 relays, no application, spring connectors)
•IPRO.CHILL
oIPC115D (15 relays, with application chiller/heatpump, disconnectable connectors )
oIPC115D SSR (15 relays, with application chiller/heatpump, disconnectable connectors)
•EXPANSION
oIPX125D (25 relay, disconnectable connectors)
oIPX225D (25 relay, spring connectors)
oIPX115D (15 relay, disconnectable connectors)
oIPX215D (15 relay, spring connectors)
4 DIN versions:
•IPRO.GENIUS
oIPG108D (8 relays, no application, disconnectable+screw connectors)
oIPG208D (8 relays, no application, spring+screw connectors)
oIPG108E (8 relays, LED display, without application, diconnectable+screw connectors)
oIPG208E (8 relays, LED display, without application, spring+screw connectors)
•IPRO.CHILL
oIPC108E (8 relays, LED display, with application chiller/heatpump, diconnectable+screw
connectors)
•IPRO.LINK
oIPL500D (connectivity module)
•EXPANSION
oIPX106D (6 relay, disconnectable connectors)
oIPX206D (6 relay, spring+screw connectors)
oIPX306D (6 relay, disconnectable+screw connectors)
•ELECTRONIC VALVE DRIVER
oXEV20D (driver for electronic valve – up to 2 valves per driver)

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 11/72
4.1 IPRO.GENIUS AND IPRO.CHILL (IPG100D – IPC100D RANGES)

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 12/72
4.1.1 Description of the connections
Connector Description
Connector for 24Vac/dc power supply
Analogue inputs (Pb1 - Pb10, PbC)
Additional power (+5Vdc, +12Vdc, GND)
Analogue outputs (Out1 - Out6, TF1 - T2)
Additional power (+12Vdc, GND)
Potential free opto-insulated digital inputs (DI1 - DI20, DIC)
USB port for downloads (BIOS, ISaGRAF® application, maps of parameters, remote display
applications, network configuration, website) and uploads (log files)
TCP/IP Ethernet port
Connector for remote terminal (VISOGRAPH), maximum 2 terminals per iPRO.
CANBUS connector for expansions (IPEXx0D) and drivers for electronic valves (XEVx0D
Rx and Tx LED to indicate that communication is active
Closed circuit terminal (Term)
RS485 Slave connector
Rx and Tx LED to indicate that communication is active
Closed circuit terminal (Term)
RS485 Master connector
Rx and Tx LED to indicate that communication is active
Closed circuit terminal (Term)
Digital relay outputs (115D, 110D, 415D, 410D versions)
3 NO relays + 1 changeover relay, 1 common
Digital relay outputs (115D, 110D, 415D, 410D versions)
6 NO relays, 2 common
Digital relay outputs (only for 115D and 415D versions)
3 NO relays + 2 changeover relays, 3 common (for 115D and 415D versions)
5 relays SSR (for 415D SSR version) *** different connection ***
Green LED to indicate the presence of power
Jumper to activate the RESCUE MODE
Yellow status LEDs (LED1) and red LED (ALARM)
See relative paragraph
Connector for NC contact to reset an external modem
RS232 connector for an external GSM modem connection (SIEMENS TC35)
Connector for an internal analogue modem

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 13/72
4.1.2 Description of the inputs and outputs
Input
No. Type of Input Description
1 Supply Reference “-“/GND power (24Vac or 24Vdc)
2 Pb1 Configurable analogue input 1 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
3 Pb2 Configurable analogue input 2 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
4 Pb3 Configurable analogue input 3 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
5 Pb4 Configurable analogue input 4 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
6 Pb5 Configurable analogue input 5 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
7 PbC Common analogue inputs (NTC, PTC, DI)
8 GND (-)
Additional power reference 5Vdc and 12Vdc and analogue inputs (0 - 20mA, 4 - 20mA, 0 - 10V,
0 - 1V, 0 - 5V)
9 Supply Reference “+“ power supply (24Vac or 24Vdc)
10 Pb6 Configurable analogue input 6 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
11 Pb7 Configurable analogue input 7 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
12 Pb8 Configurable analogue input 8 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
13 Pb9 Configurable analogue input 9 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
14 Pb10 Configurable analogue input 10 (NTC, PTC, 0 - 20mA, 4 - 20mA, 0 - 10V, 0 - 1V, 0 - 5V, DI)
15 +5V Additional power +5Vdc
16 +12V Additional power +12Vdc
21 Out1 Analogue output 1 0 - 10V
22 Out2 Analogue output 2 0 - 10V
23 Out3 Analogue output 3 0 - 10V
24 Out4 Analogue output 4 0 - 10V
25 GND(-) Additional power reference 12Vdc and analogue outputs
26 Out5 Analogue output 5 0 - 10V, 4 - 20mA, Relay (if TF1 is not used)
27 Out6 Analogue output 6 0 - 10V, 4 - 20mA, Relay (if TF2 is not used)
28 TF1 Analogue output TF1 PWM (if Out5 is not used)
29 TF2 Analogue output TF2 PWM (if Out6 is not used)
30 +12V Additional power +12Vdc
40 DI1 Opto-insulated digital input 1 (potential free contact)
41 DI2 Opto-insulated digital input 2 (potential free contact)
42 DI3 Opto-insulated digital input 3 (potential free contact)
43 DI4 Opto-insulated digital input 4 (potential free contact)
44 DI5 Opto-insulated digital input 5 (potential free contact)
45 DI6 Opto-insulated digital input 6 (potential free contact)
46 DI7 Opto-insulated digital input 7 (potential free contact)
47 DI8 Opto-insulated digital input 8 (potential free contact)
48 DI9 Opto-insulated digital input 9 (potential free contact)
49 DI10 Opto-insulated digital input 10 (potential free contact)
50 DIC Common opto-insulated digital inputs 1 to 20
51 DI11 Opto-insulated digital input 11 (potential free contact)
52 DI12 Opto-insulated digital input 12 (potential free contact)
53 DI13 Opto-insulated digital input 13 (potential free contact)
54 DI14 Opto-insulated digital input 14 (potential free contact)
55 DI15 Opto-insulated digital input 15 (potential free contact)
56 DI16 Opto-insulated digital input 16 (potential free contact)
57 DI17 Opto-insulated digital input 17 (potential free contact)

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 14/72
58 DI18 Opto-insulated digital input 18 (potential free contact)
59 DI19 Opto-insulated digital input 19 (potential free contact)
60 DI20 Opto-insulated digital input 20 (potential free contact)
61 DIC Common digital inputs 1 to 20
70 RL1 Relay 1 normally open contact
71 RL2 Relay 2 normally open contact
72 RL3 Relay 3 normally open contact
73 C Common relays 1, 2, 3 and 4 (MAX 6A)
74 RL4 Relay 4 normally open contact
75 RL3 Relay 3 normally closed contact
76 C Common relays 5, 8 and 9 (MAX 6A)
77 RL5 Relay 5 normally open contact
78 RL6 Relay 6 normally open contact
79 RL7 Relay 7 normally open contact
80 RL8 Relay 8 normally open contact
81 RL9 Relay 9 normally open contact
82 RL10 Relay 10 normally open contact
83 C Common relays 6, 7 and 10 (MAX 6A)
84 RL11 Relay 11 normally open contact
85 RL12 Relay 12 normally open contact
86 RL13 Relay 13 normally open contact
87 C Common relays 12, 13 and 15 (MAX 6A)
88 C Common relays 12, 13 and 15 (MAX 6A)
89 RL11 Relay 11 normally closed contact
90 C Common relays 11 and 14 (MAX 6A)
91 RL14 Relay 14 normally open contact
92 RL14 Relay 14 normally closed contact
93 RL15 Relay 15 normally open contact
94 RS485 Master RS485 Master connection (-)
95 RS485 Master RS485 Master connection (+)
96 RS485 Master RS485 Master connection (insulated gnd)
97 RS485 Slave RS485 Slave connection (-)
98 RS485 Slave RS485 Slave connection (+)
99 RS485 Slave RS485 Slave connection (insulated gnd)
100 CAN Bus CAN Bus connection (+), not open
101 CAN Bus CAN Bus connection (-), not open
102 CAN Bus CAN Bus connection (insulated gnd), not open
103 Remote Display Connection for VISOGRAPH remote terminal (Vnr)
104 Remote Display Connection for VISOGRAPH remote terminal (+)
105 Remote Display Connection for VISOGRAPH remote terminal (-)
106 Modem Reset NC relay input to reset an external modem (24Vac/dc)
107 Modem Reset NC relay output to reset an external modem (24Vac/dc)
Version with SSR relay
84 RL11 Relay 11 normally open contact
85 RL11 Common relays 11
86 RL12 Relay 12 normally open contact
87 RL12 Common relays 12
88 RL13 Common relays 13

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 15/72
89 RL14 Relay 14 normally open contact
90 RL14 Common relays 14
91 RL15 Relay 15 normally open contact
92 RL15 Common relays 15
93 RL13 Relay 13 normally open contact

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 16/72
4.1.3 Technical specifications
4.1.3.1 Analogue inputs
Analogue conversion type: 10-bit A/D converter
Number of inputs: 10
Type of analogue input:
(configurable via software parameter) NTC Dixell (-50T110°C; 10KΩ±1% at 25°C)
PTC Dixell(-55T115°C; 990Ω±1% at 25°C)
Digital input (potential free contact)
Voltage: 0 - V, 0 - 5V, 0 - 10V (input resistance 3.7KΩ)
Current: 0 - 20mA, 4 - 20mA (input resistance 100Ω)
Digital input status variation detection time: 100ms (in any case it depends on the cycle time set by the user in the
given application)
Accuracy: NTC, PTC: ±1°C
0-1V: ±20mV
0-5V: ±100mV
0-10V: ±200mV
2-20mA, 4-20mA: ±0.30mA
Additional power: +12V: 200mA in total (between +12V and analogue outputs)
+5v: 100mA
Notes: Any inputs that are powered with a voltage that differs from that supplied
by the device (+12V or +5V) must be powered separately with another
transformer (do not use the same secondary of the controller's power) in
order to prevent the inputs from malfunctioning or being damaged.
4.1.3.2 Digital inputs
Type:
(configurable via software parameter) Opto-insulated potential free contact
Number of inputs: 20
Digital input status variation detection time: 100ms (in any case it depends on the cycle time set by the user in the
given application)
Notes: Do not use live contacts in order to prevent the inputs from being
damaged.
4.1.3.3 Analogue outputs
Type: Non opto-insulated internal power
Number of outputs: 6
Type of analogue output:
(configurable via software parameter) 4 fixed outputs 0-10Vdc (Out1 - Out4)
2 configurable outputs (alternative):
- 0-10Vdc, 4-20mA (Out5 and Out6)
- PWM to be used with Dixell XV modules (TF1 and TF2)
Maximum load: 40mA (Out1 - Out4)
20mA (Out5 and Out6) max with configured outputs 0-10Vdc
400Ωmax with configured outputs 4-20mA
22Ωper live analogue output
Accuracy: Out1 - Out4: ±2% full scale
Out5 – Out6: ±2% full scale
Resolution: 8bit
Notes: The electrical devices controlled by these analogue outputs must be
powered separately with another transformer (do not use the same
secondary of the controller's power) in order to prevent the outputs from
malfunctioning or being damaged.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 17/72
4.1.3.4 Standard Digital outputs
Type: Relays with NO or NC contacts, depending on the model
Number of outputs: 10 or 15, depending on the model
Type of output:
(configurable via software parameter) Relays with normally open contact:
- RL1, RL2, RL4, RL5, RL6, RL7, RL8, RL9, RL10, RL12, RL13, RL15
Relays with changeover contact:
- RL3, RL11, RL14
Maximum load: Relays with normally open contact: 5A(250Vac) SPST 5(2)A
Relays with changeover contact: 8A(250Vac) SPDT 8(3)A
Notes: Verify the capacity of the output used. There is double insulation between
the digital outputs and the low voltage of the rest of the circuit.
Do not use different voltages for the various groups of relays nor within
each group.
4.1.3.5 SSR Digital outputs version
Type: Relays with NO or NC contacts, depending on the model
Number of outputs: 10 or 15, depending on the model
Type of output:
(configurable via software parameter) Relays with normally open contact:
- RL1, RL2, RL4, RL5, RL6, RL7, RL8, RL9, RL10, RL11, RL12, RL13,
RL14, RL15
Relays with changeover contact:
- RL3
Maximum load: Relays with normally open contact: 5A(250Vac) SPST 5(2)A
Relays with changeover contact: 8A(250Vac) SPDT 8(3)A
SSR relays with normally open contact 1A(12 - 250Vac):
- only in AC load
- minimum current is 50mA (equivalent to 12W - 250Vac)
- internal impedance 300KΩ(current 0.2mA at 250Vac with an open
contact)
Notes: Verify the capacity of the output used. There is double insulation between
the digital outputs and the low voltage of the rest of the circuit.
Do not use different voltages for the various groups of relays nor within
each group.

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 18/72
4.1.3.6 Wiring diagrams

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 19/72
4.1.3.7 Mechanical specifications
10 DIN module
4.1.3.8 Electrical specifications
Power Supply: 24Vac +10/-15%, 50/60Hz
20 - 36Vdc
Consumption: 20VA (Vac), 15W (Vdc)
Connectors: Molex connectors with low voltage wiring
SELECOM/CIVILUX connectors for digital outputs (250Vac, 6A max)
Microprocessor: AT91RM9200 32-bit 200Mhz
Permanent FLASH memory: 128MB, in 8-bit
RAM: 32MB or 64MB, in 16-bit
Internal clock: standard
4.1.3.9 Plastic container
Mount: On a DIN rail (EN 50022, DIN 43880)
Fastened with screws via the removable plastic flaps.
Material: PC-ABS Thermoplastic
Self-extinguishing: V0 (UL94)
Comparative Tracking Index (CTI): 300V
Colour: Black
4.1.3.10 Product certifications
Control to classify with the definitions 2.5.1 e 2.5.2 mentioned in the section 2.5 of the general
requirements EN60730-1 (2.5.1 = integrated control, 2.5.2 = incorporated control).
Electrical safety:
•EN60730-1
Electromagnetic compatibility:
•EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8,
EN61000-4-11

1592025700 IPROFAMILY stp GB 2012.08.08.doc iPro Series 20/72
4.2 IPRO.GENIUS (IPG200D RANGE)