DNF Controls ST600-KIPRO User manual

ST600-KIPRO User Manual
Page 1of 16
ST600-KIPRO
User Manual

ST600-KIPRO User Manual
Page 2of 16
TABLE OF CONTENTS
GETTING STARTED............................................................................................... 3
EQUIPMENT LIST................................................................................................. 3
INSTALLATION..................................................................................................... 4
SYSTEM CONFIGURATION WEB PAGE .................................................................. 5
CONNECTION TO AJA KI-PRO.................................................................................. 7
OPERATION ........................................................................................................ 8
CLIP LIST WEB PAGE ...........................................................................................10
8. FUNCTION TABLE ...............................................................................................11
9. KEY LAYOUT.......................................................................................................13
10.SPECIFICATIONS .................................................................................................14
11 DNF CONTROLS LIMITED WARRANTY..................................................................16
REVISIONS
1.00
01/24/17
Original draft.

ST600-KIPRO User Manual
Page 3of 16
NOTE: KiPro Rack does not support Search to Time or Shuttle or Slomo functionality.
KiPro Ultra does not support Shuttle or Slomo functionality.
1. GETTING STARTED
1. Go to Installation Section to set up ST600.
2. Go to System Configuration Section to set static IP address, Subnet Mask, and
Gateway address.
3. Go to Remote Device Assignment Section to enter IP addresses for remote devices that
ST600 will communicate with.
4. Go to System Configuration section to set default settings.
2. EQUIPMENT LIST
Qty
Component
DNF Part Number
1
ST600 Panel
ST600-KIPRO
1
ST600 POWER SUPPLY
included
1
POWER CORD
included

ST600-KIPRO User Manual
Page 4of 16
3. INSTALLATION
1. Connect supplied power supply to POWER connector
2. Connect Ethernet cable to ETHERNET connector.
Rear View
DEFAULT ETHERNET CONFIGURATION
IP Address:
192.168.10.217
Subnet Mask:
255.255.255.0
Gateway:
192.168.10.1
The ST600 is configured using a standard web browser (Internet Explorer, Firefox, and Chrome).
Enter the IP address in the Address/ URL bar, typically located at the top of the web browser
page, to access the Home Page. Use the links on the left side of the Home Page to access the
desired configuration web pages.
All configuration settings are saved in non-volatile memory in the ST600. Settings are retained
when power is removed.
Settings may be uploaded to a computer as a configuration file (.dnf) for storage. Configuration
files may be downloaded from a computer into the ST600 to restore a saved configuration. A
configuration file contains all of the ST600’s configurations except IP address, subnet mask, and
gateway address. The ST600 does not support partial configuration upload or download. The
configuration file is a not a text formatted file. It cannot be viewed or modified with a text
editor.
To access the System Configuration web page, use the following log-on when prompted:
Username: dnfuser
Password: controls

ST600-KIPRO User Manual
Page 5of 16
4. SYSTEM CONFIGURATION WEB PAGE
SELECTION
DESCRIPTION
P1 Software Upgrade:
Use this link to install the P1 upgrade file provided by DNF Controls
P2 Software Upgrade:
Use this link to install the P2 upgrade file provided by DNF Controls
Web Upgrade:
Use this link to install the Web pages upgrade file provided by DNF
Controls
Save Configuration to PC:
Use this link to save the ST600 current configuration to a
configuration file on a computer. The web browser will prompt for
file name and directory. The file extension must be ‘dnf’.

ST600-KIPRO User Manual
Page 6of 16
SELECTION
DESCRIPTION
Restore Configuration from PC:
Use this link to download a configuration file from your computer to
the ST600. The web browser will prompt for directory and
configuration file name. The file extension must be ‘dnf’.
Set Factory Defaults:
Use this link to reset all ST600 configuration settings to factory
defaults. This will NOT change the IP address, subnet mask or
gateway address. The ST600 will automatically reboot.
Enter Label:
Enter label to be displayed on top right of all web pages
Enter the new IP settings below:
Enter the new IP address, Gateway, and Subnet Mask. Click on “Save
Config”to save the new entries. The ST600 will automatically
reboot.

ST600-KIPRO User Manual
Page 7of 16
5. CONNECTION TO KI PRO
1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the
configuration pages.
2. Select the Remote Device Assignment link located on the left hand side of the web
page.
3. In the Remote Device Assignment page, create a device label for the AJA KIPRO you
will be connecting to.
4. In the “Device type” column, select “KIPRO” from the dropdown menu.
5. In the “Connection type” column, select “TCP” from the dropdown
menu
6. In the “Connection Mode” column, select “Client Transmit/Receive”
from the dropdown menu.
7. In the “IP Address” column, enter the IP address of the Ki Pro. Next
under “Port Number” set the Port number to “80”.
8. Press “Save” to save your changes.
The ST600-KiPro communicates over IP to AJA KiPros using the KiPros's native control
protocol. The native control protocol does not provide a means to synchronously roll multiple
units. As a result, transport commands are sent to each KiPro, one at a time. There will be a
delay between KiPros based upon inherent IP network delays and each KiPro's command
processing delay after receiving the command.

ST600-KIPRO User Manual
Page 8of 16
6. OPERATION
LCD DISPLAY
During normal operation, the top row of the display shows the selected time mode
and current time location of the selected Ki Pro.
For example: 01:12:09:23
Second Row shows name of loaded clip
.
.
For example: Clip: SC1TK47
TRANSPORT CONTROL
Select the desired transport function by pressing the appropriate key. The Real-Time
Status Indicators will light to indicate the DDR's current transport mode.
See Function Table (Pg 12) for a full list of functions and a description of each function.
CREATE AND RECORD CLIP FROM WEB PAGE
1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the
configuration pages.
2. Select the Clip List link located on the left hand side of the web page.
3. In the Clip list page, create a new clip in the following window:
4. Press the “Create and Record” button to create the desired clip and to begin the
recording.
LOAD CLIP FROM WEB PAGE
1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the
configuration pages.
2. Select the Clip List link located on the left hand side of the web page.
3. In the Clip list page, select the desired clip to load and select the LOAD button under
the Load Clip column.
Your clip will now be loaded and ready to play.

ST600-KIPRO User Manual
Page 9of 16
LOAD A CLIP FROM ST600-KIPRO
1. Press [SHIFT/ESC] + [LOAD] to set the ST600-KiPRO into a “LOAD” mode.
2. Once in “LOAD”mode, use numeric keys 0-9 of the panel (yellow silkscreen) to call
up the desired clip number
3. After the numeric clip ID is entered, Press [LOAD] key to execute the load.
Your clip will now be loaded and ready to play.
CUE POINTS
1. Press the [MARK] key to mark the Ki Pro’s current time into the selected cue point #.
2. Use [↑] or [↓] to step through marked cue points.
3. Press the [LOAD] key to load the currently selected cue point.

ST600-KIPRO User Manual
Page 10 of 16
CLIP LIST WEB PAGE
Load Clip For Play
Choose from the list of Clips and simply press “LOAD”.
Clip will load and show time and name of loaded clip on ST600 LCD
display.
Create Clip for
Record
Type in name you wish to create for your clip and click on “Create &
Record” on ST600 Clip List web page to create the desired clip.
*Record will start once “Create & Record” is pressed on web page
or when
Record key is pressed on the ST600