Dog Care TC01 User manual

ON OFF
®
[phone]
Model: TC01
Remote: TC01-C1
Reciver: TC01-R1
If any quality problems or confusion, feel free to contact us via
[email protected]

Turn on the receiver : Hold the ON/OFF button for 2 seconds and the
receiver will beep and vibrate.
ON OFF
2
Complete charging in 2 hours.Offer only one wire in the package.
1120Minutes
1
2s

4
To turn the transmitter on.
Security Keypad Lock: Toggle it down to unlock.
3
ON / OFF
2

6
Vibrate Command: Press the vibration button briefly and the receiver
vibrates once.
Beep Command: Press the beep button briefly and the receiver beep
once.
5
ON
OFF
ON OFF
3
ON OFF

Static Intensity Adjustment: Press and hold the LEVEL button while
rotating the remote control switch to adjust the shock intensity. Static
Command: Press the static button briefly and the receiver shock once.
Channel Switching: Able to train 9 dogs at the same time. Press
the channel button briefly to select the dog to train.
7
89
4
HOLD

ON OFF
Model: TC01
If any quality problems or confusion, feel free to contact us via
[email protected]
NO OFF
®
[phone]
I. Package Content
123
45
Remote Control Receiver Collar
Silicone Caps X 2
USB Cable Lanyard User Manual
6 7
5
Pairing: Refer to “Page10”for more information.
9
ON OFF
5s

ON OFF
including
Silicone Caps
for electrodes
Receiver Static Electrodes
ON/OFF
USB Charging Port
& Rubber Lid
Sound
Speaker
LED Status
Light
6
1. Only when both electrodes are simutaneously touched, shock will work.
2. If collar has a delayed reaction or fails to sync up even in short distance, make sure there is no strong
signal interference in your surroundings. The remote's range could be affected by obstacles,
electromagnetic field, or even stormy weather.
3. If you find collar cannot work, please check whether you push the lock button on which is on the left
side of remote.
4.The sensitivity to static depends on your dog's siz weight, amount of fur, and even skin condition.
When wearing the collar, it is most suitable if one finger can be insert
ed under it. Too tight is not good for your dog, but too loose will dull
the static function for the electrodes cannot touch your dog’s skin.
If your dog has thick
fur, please separate
the fur apart so that
both electrodes can
touch the skin.
Make sure protective
silicone caps are off
the electrodes. They
can dull the static
sensation sent to your
dog.
COLLAR STATIC STIMULATION QUICK GUIDE
Not feelling the SHOCK? Try these solutions.
Note:
One last thing you
cantry is to shear the
fur where both electr-
odes aretouched.
Water can help con-
duct electricity If you
spray some water
around the electrodes,
the shock function can
be feltmore effectively.

II.Product Overview
ON & OFF Switch /
Static Level Regulator
Keypad Lock
Static Level Regulator
Activation Button
Vibrate Button
Antenna
Display Screen
Static Button
Channel Switch /
Match Button
Beep Button
Lanyard Holder
Micro USB
Charging Port
Training
Mode
Keypad
Lock
Remote’s
Signal
Battery Status (Remote)
Battery
Status
(Receiver)
Channel Display
(1-9)
Static Level
Display
(01-99)
Screen
Remote Control
7

III. Setting Up
Remote Control: Charge the device until the battery icon on the display
indicates full bars.
Receiver: Charge the device until the red LED turns green. The display
on the Remote will indicate full bars as well.
1. Charge the devices respectively for 2-3 hours.
If you charge it for a long time. The receiver couldn't hold a charge.
1. Thread the collar through the Receiver.
2. If your dog has thick fur, please separate the fur at the
electrodes with a comb to enable them to reach the skin.
IV. Wearing the Receiver Collar
2. Configurating Static Levels:
Press and hold Static Level Regulator Activation Button and simultane-
ously slowly rotate Static Level Regulator until the digit on the screen
reaches a suitable strength.
Recommended Static Level strength starts from “10”. This is the
minimum sensation your dog can feel. The right static level goes down to
an individual basis that your dog is responsive to the shock function.
The sensitivity to static depends on your dog’s size and weight, amount of
fur, and even skin condition.
8

V. Training Modes
1. Vibration Mode:
Press Vibrate Button, and the Receiver will vibrate once; hold the button
and the vibration persists.
2. Sound Mode:
Press Beep Button, and the Receiver will give a “beep” sound; hold the
button and the “beep” sound persists.
3. Static Stimulation Mode:
Press the Static Button, and the Receiver will give a Static Stimulation to
the wearer.
Do not hold the button as it is not recommended to have prolonged
shock to your dog. However, the static will be cut off in 4 secs.will cut off
in 4 secs automatically to prevent unintentional harm to your pet.
4. Switching Channel:
Press the Channel Switch Button to choose which Receiver you want to
control when you match more than one Receiver.
NO OFF
ON OFF
3. When wearing the collar, the tightness is at most fit if
one finger can be inserted underneath.
4. The Silicone Caps can dull the static sensation, you
should decide weather you need to put them on. The
soft caps also protect your dog from direct contact with
metal electrodes, which in some cases will cause
discomfort.
9

ON OFF
‘beeps’
‘vibrates’
OFF
ON
‘beeps’
‘vibrates’
OFF
VII. Training Tips
VI. Match the Remote Control to the Receiver:
1. Reward your dog with food will usually help to achieve the best
result.
2. Do not use the device on dogs aged below 6-month, old, pregnant,
easily frightened, aggressive, in heat, old, and dogs not in best of health.
*You may skip this step because the set is already paired by factory setting.
After confirming that the receiver is turned off,
hold the ON/OFF button of receiver for 5 seconds until
the LED indicator Light on receiver flashes in green.
Press and hold Channel Switch / Match Button for 5 secs. The
Receiver will vibrate and beep which indicates the matching is completed.
You will see “1” (or subsequent number) in the Channel Display when the
match is successful.
Adding multiple Receivers:
After confirming that the receiver is turned off, hold the ON/OFF button
of receiver for 5 seconds until the LED indicator Light on receiver flashes
in green.Press and hold Channel Switch /Match Button for 5 secs
(repeat steps 2.1 and 2.2). The Channel Display will show the subsequent
number of the new Receiver. Note: Connect only 1 Receiver at a time, do
not connect all simultaneously, or the Remote will match all Receivers into a
single channel.
Removing all Matched Receivers:
Press and hold Static Level Regulator Activation Button and Beep Button
simultaneously for 5 secs. The Channel Display will default to “0”. Note:
Make sure all Receivers you want to remove have power and in the effective
range, so that Receivers could receive the remove command.
10

VIII.Important Notice
Regarding you and the product:
1. It is strictly prohibited to open the Receiver in any situation. Doing so will
likely compromise the waterproof function and thus voiding the product
warranty.
2. Please use Remote Control and Receivers from the complete set, do not
use other product to match with the Receiver.
3. If you want to test the product, please use professional testing apparatus.
Do not test with hands, so as to avoid accidental injury.
4. If find water at the charging port, please wipe it dry before charging.
5. Beware the interference from the environment can cause the product not
to work properly. For examples are places with high voltage facilities,
communication towers, thunderstorm, large buildings, and strong
electromagnetic interference.
6. Receiver will be turned off if idling for 8 hours.
7. The included collar is a basic accessory and is not necessarily suitable
for all types of dog breeds. Any collar not wider than 24mm and not thicker
than 5mm, made of soft material, can be a replace ment for the current
collar.
Regarding well-being of your dog:
1. The Receiver collar is not a regular collar and not recommended to put
on a leash to walk your dog. (Doing so during pulling may hurt the dog due
to protruding electrodes on the Receiver.)
2. Do not put the collar on for over 12 hours, it may cause rashes or discomfort
to your dog’s skin.
3. Do not allow children, or anyone who has little to no experience with
training dogs, to handle this training kit.
4. In order to guarantee normal diving function, please insert the waterproof
rubber lid over the charging port.
5. Static stimulation is not a pleasant experience for any dogs. Punishment
3. Use verbal commands first, and supplement with a corrective stimulus
only as needed. Be consistent with your verbal commands, using the
same words every time. Work with your pet on one behavior at a time to
avoid confusion and frustration. Use as little stimulus
4. as possible and only to reinforce verbal commands when necessary. Do
not over correct your dog.
5. For example, use the beeps as warning by pressing Beep Button. The dog
will become conditioned to the beep preceding the corrective stimulus
and will soon learn to recognize the beep as a warning along with your
verbal command.
6. Do not rely on this product solely to train your dog. Some dogs will not
respond to this product. We cannot guarantee the effectiveness of this or
any trainer on your dog.
If your dog shows signs of growling,snarling,biting or aggression
while using the collar, discontinue use immediately and contact a
professional trainer for advice.
is harsh way to train a dog. Always, the praise could encourage your dog
for good behavior. Note: With Anti-Misoperation design, Static function
always cut-off after 4 secs, this is a precaution designed to prevent
unintentional long-pressed of the button, and potential animal abuse.
11

IX. Troubleshooting
X. Operating Environment & Maintenance
Regarding you and the product:
1. It is strictly prohibited to open the Receiver in any situation. Doing so will
likely compromise the waterproof function and thus voiding the product
warranty.
2. Please use Remote Control and Receivers from the complete set, do not
use other product to match with the Receiver.
3. If you want to test the product, please use professional testing apparatus.
Do not test with hands, so as to avoid accidental injury.
4. If find water at the charging port, please wipe it dry before charging.
5. Beware the interference from the environment can cause the product not
to work properly. For examples are places with high voltage facilities,
communication towers, thunderstorm, large buildings, and strong
electromagnetic interference.
6. Receiver will be turned off if idling for 8 hours.
7. The included collar is a basic accessory and is not necessarily suitable
for all types of dog breeds. Any collar not wider than 24mm and not thicker
than 5mm, made of soft material, can be a replace ment for the current
collar.
Regarding well-being of your dog:
1. The Receiver collar is not a regular collar and not recommended to put
on a leash to walk your dog. (Doing so during pulling may hurt the dog due
to protruding electrodes on the Receiver.)
2. Do not put the collar on for over 12 hours, it may cause rashes or discomfort
to your dog’s skin.
3. Do not allow children, or anyone who has little to no experience with
training dogs, to handle this training kit.
4. In order to guarantee normal diving function, please insert the waterproof
rubber lid over the charging port.
5. Static stimulation is not a pleasant experience for any dogs. Punishment
1. Remote/Receiver runs out of power quickly; not charging
Make sure the charger and Remote/Receiver is securely connected. Try
to use other universal android USB cable to charge.
2. Static is too weak or even completely no static; Static Mode has no
effect on my dog. Make sure the receiver has enough power(when it is
low-battery, shock doesn't work); Only both electrodes are simultaneous
ly touched by dog's skin shock will work; Try to increase the static level to
more than 45. If dog has long hair, you need to separate dog hair to
make electrodes touched.
3. Remote/Receiver does not response
Recharge the Remote/Receiver,make sure they have enough power.
Check the keypad lock(which is on the left side of Remote), unlock the
Remote. If Remote is locked, there will be a lock icon on the display. If
you try methods above but still fail, please remove all the matching and
reconnect Remote with Receivers.
4. Receiver is fully charged, but Remote Display still shows receiver
has empty battery.
Turn off Remote and turn on Remote again.
5. Fail to match Receiver with Remote
Make sure Receiver is connected to a power source( charging mode can
only be activated while charging).Must hold Channel Switch more than 5
secs, if not, matching will fail.If you still fail after trying as above, contact
us via 【[email protected] 】to confirm whether receiver and
remote is of the different version, we will solve for you.
6. Training mode fails to sync up even in a very short distance
Make sure there is no strong signal interference in your surroundings.
Remote's range could fluctuate subjects to obstacles, electromagnetic
field, or even stormy weather.
7. Receiver beeps, vibrates, shocks by itself constantly or occasionally.
Make sure no button of Remote has been pressed or gotten stuck.
If any quality problems or confusion, feel free to contact us via
[email protected].
Do not use the product in the circumstances as follow:
1. Do not operate the devices under temperature of 104°F and above, doing
so in such high temperature will decrease the performance of the batteries.
2. Do not use the Remote during snowing, this could lead to water sipping in
causing damage to the controller.
3. Do not use the set in places with strong electromagnetic interference. This
will greatly compromise the performance of the product.
is harsh way to train a dog. Always, the praise could encourage your dog
for good behavior. Note: With Anti-Misoperation design, Static function
always cut-off after 4 secs, this is a precaution designed to prevent
unintentional long-pressed of the button, and potential animal abuse.
12

XII. FCC Statements
XI. Terms of Use & Limitation of Liability
1. Use of this product means you accept all the terms and conditions.
2. This product is a professional dog training device. You are not
recommended to use this product if your dog is clever and less than 15
lbs in weight. If you're not sure whether the product is suitable for your
pet dog, please consult a professional handler or contact us.
3. This product is a professional dog training device and should not be used
for other purposes. Please do not violate local laws in using this product.
4. We bear no liability for any direct or indirect losses caused by use or
misuse of this product; all risks in using this product shall be borne by
user.
5. Please contact the dealer for parts warranty, goods return or exchange.
We provide only technical support.
6. We reserve the right to alter the terms, conditions and notices of this
product offered.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
4. Avoid dropping the devices on hard surface or inflict excessive force on
them.
5. Avoid using the devices in environment flooded with corrosive chemical,
this may lead to color degrading, deforming, or cracking of exterior of the
devices.
Maintenance:
1. When not in use, please wipe clean both the Remote and Receiver with
mild detergent. Turn off the Remote, lock the keypad, put on the rubber lid
on the Receiver’s charging port, and store the set in a cool dry place.
2. During cleaning, wipe with soft cloth and mild detergent. Do not use hard
brushes which may scratch the surface of the device.
3. If the Receiver has gotten dirty, secure the charging port rubber lid secured
and wash it thoroughly. Note: Do not submerge the Receiver into water for
long period of time, even though it is waterproof.
4. If found residues around the charging port’s rubber lid, you should wipe it
clean to prevent water from sipping in.
5. If the Remote fell into water, pick it up quickly and turn off the power. Dry it
with cloth as much as you can and let it out to dry. It should resume function
normally once the moisture is dried out.
13

XIII. Product Specification
Model
Package Dimension
Neck Circumference
Receiver’s Casing
Remote’s Casing
Remote / Receiver’s Battery
Charging Voltage
Remote / Receiver
Charging Time
Charging Port
Wireless Power
Operating Environment
Remote / Receiver
Standby Time
Remote to Receiver’s
Signal Range Distance
Receiver’s Battery Sync
Distance
TC01
9.8″ – 24.8″
9.0″ X 4.9″ X 2.1″
IP67 waterproof;
Non-waterproof;
Keep away from water
250mAh
DC 5V/500mAh
Full Charge at 2-3 hrs
Micro USB
10mW
32°F-104°F, <95% Rh
Remote: 45 days;
Receiver: 15 days
1000 Ft
164 Ft
a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
14

®
[phone]
If any quality problems or confusion, feel free to contact us via
[email protected]