Dog Care TC05 User manual

®
[phone]
If any quality problems or confusion, feel free to contact us via
[email protected]
Model: TC05

2
1
Complete charging for 2 hours. Offer only one wire in the package.
Collar Fitting: Adjust to the comfortable size; make sure the receiver’s
contact points are placed snugly against your pet’s skin.
1120Minutes

2
4
To turn the transmitter and receiver on.
Security Keypad Lock: Toggle it down to unlock.
3Hold 1.5seconds

3
5
6
Vibrate Command: Press the vibration button briefly and the receiver
vibrates once.
Beep Command: Press the beep button briefly and the receiver
beeps once.

4
8
Static Intensity Adjustment: Press and hold the LEVEL button
while rotating the remote control switch to adjust the shock
intensity. Static Command: Press the static button briefly and the
receiver shocks once.
Channel Switching: Able to train 3 dogs at the same time. Toggle
the channel button to select the dog to train.
7

5
Pairing: Refer to “Page10” for more information.
9
When wearing the collar, it is most suitable if one finger can be insert
ed under it. Too tight is not good for your dog, but too loose will dull
the static function for the electrodes cannot touch your dog’s skin.
If your dog has thick
fur, please separate
the fur apart so that
both electrodes can
touch the skin.
Make sure protective
silicone caps are off
the electrodes. They
can dull the static
sensation sent to your
dog.
COLLAR STATIC STIMULATION QUICK GUIDE
Not feelling the SHOCK? Try these solutions.
One last thing you
can try is to shear the
fur where both electr-
odes are touched.
Water can help con-
duct electricity if you
spray some water
around the electrodes,
the shock function can
be felt more effectively.

I．Package Content
12
3
45
1Remote Control 3USB charging wire
4Lanyard 5User Manual
2Receiver
6
®
[phone]
If any quality problems or confusion, feel free to contact us via
[email protected]
1. Only when both electrodes are simutaneously touched, shock will work.
2. If collar has a delayed reaction or fails to sync up even in short distance, make sure there is no
strong signal interference in your surroundings. The remote's range could be affected by obstacles,
electromagnetic field, or even stormy weather.
3. If you find collar cannot work, please check whether you push the lock button on which is on the
left side of remote.
4.The sensitivity to static depends on your dog's size weight, amount of fur, and even skin
condition.
Note:
Model: TC01

Remote Control
1
2
3
4
13
Antenna
Security Keypad Lock
LCD Display
5
6
7
8
Channel Switching
Button
Static Intensity
Adjustment Button
Pairing Button
(Reverse Side)
Static Mode Button
Vibrate Mode Button
Beep Mode Button
9
10
11
12
LED Indicator
Light
Charging Port
On/Off Button
14 Charging Port
15 Contact Points
Static Intensity
Security Keypad Lock
7
1
2
3
5
6
78
9
11
12
13
15
14
On/Off Button (Static
Intensity Regulator)
Screen
Signal Transmission
Status
Remote Control
Battery’s Power
Level
Channel Display
10
4

Ⅱ．Set up
Ⅲ．Wearing the Receiver Collar
1. Charge the devices respectively for 2 hours and above.
a. Remote control: The battery icon of remote control will be
full after it is fully charged.
b. Receiver: When red light on the receiver turns green, it is
fully charged. When the red light flashes, it is low battery.
1. Put the collar on the dog.
Set up the voltage level.
Press and hold Static Intensity Adjustment Button and simultane-
ously rotate Static Intensity Regulator until the digit on the screen
reaches a suitable intensity.
There is individual
difference, always use the
right voltage for your dog.
+1 second+
8
2. Adjust the nylon belt to the right size.
3. Cut off the excess part of the belt with
scissors.
4. Burn the be it's end with the lighter to prevent
the thread from fraying.

5.If your dog has thick hair, please separate the
hair at the electrodes with a comb from the
Contact Points area so that Contact Points
are placed snugly against your pet’s skin.
6.When properly fitted, you should be able to fit
a finger or two snugly in between the collar
and your pet’s skin.
Ⅳ. Training Mode
1.Press the vibration button briefly, and the receiver vibrates
once; hold the button, and the receiver vibrates continues.
2.Press the beep button briefly, and the receiver beeps once;
hold the button, and the "beep" sound continues.
3.Press the static button briefly, and the receiver shocks once;
hold the button is invalid.
4.Press the channel switching button to choose which receiver
you want to control if you pair more than one receiver.
9