dol sensors DOL 16 0-100/1000 LUX Manual

Technical User Guide
DOL 16 0-100/1000 LUX
0-10V
Light sensor
For other language variants of this document we refer to www.dol-sensors.com or
your local dealer.
dol-sensors a/s – Agro Food Park 15 – DK-8200 Aarhus N – T: [phone] – F: [phone] – www.dol-sensors.com

Technical User Guide
2www.dol-sensors.com DOL 16 0-100/1000 LUX 0-10V
1 Product description
The DOL 16 is a sensor designed to measure light intensity. It is intended for application in livestock houses but
is also well suited for a number of industrial applications.
Two variants of the sensor are available; one with a cable, and one with M12-connector/cable.
Light-sensitive area
Figure1: DOL 16.
2 Mounting
In dusty environments, the sensor should be placed in a position which allows for easy cleaning at regu-
lar intervals.
For optimum mounting of the sensor, use the mounting clip.
Mount the sensor in front of an inlet in the direction of the fresh air jet to ensure that the sensor is free from
dust. In houses with wall inlets place the sensor close to one of the inlets that opens first. I tunnel houses the
sensor must be placed minimum 20 meters away from the end of the tunnel opening to avoid light from outside
influencing the sensor.
The sensor should be placed in a position which is representative of the light level in the house - the light-sensi-
tive area of the sensor is shown in Figure 1.
Placement of the sensor where it is influenced by sunlight from the outside and objects obstructing light near
the sensor should be avoided.
Place the sensor in
front of an inlet that
opens first in order to
minimise the build-up
of dust on the sensor.
1/4 of the width of the livestock house.
Figure2: Mounting in the livestock house.

Technical User Guide
DOL 16 0-100/1000 LUX 0-10V www.dol-sensors.com 3
If ceiling mounting is not possible or not wanted, the sensor can be hung in the
cable 1-2 meters above the animals. If this type of mounting is used, the sensor
must be cleaned daily with a dry cloth.
When removing variant with M12 connector, the included plug must be mounted.
3 LED indication
LED indication Sensor status
GREEN ON Operation OK
RED ON Connection error
Load < 500 Ω
RED flashes Sensor defective
Over/under voltage alarm
Overload
4 Connection
Installation, servicing and troubleshooting of all electrical equipment must be carried out by quali-
fied personnel in compliance with the applicable national and international standard EN 60204-1
and any other EU standards that are applicable in Europe.
+V (Brown)
GND (Blue)
(Black)
(White)
Power
supply
11 - 30 V DC
0-1000 Lux 0-100 Lux
Figure3: Connection.
If 1:1 compliance with the L 182/19-standard is desired, measurements according to the standard and an adap-
tation to the output of the DOL 16 sensor with the chosen placement must be carried out.

Technical User Guide
4www.dol-sensors.com DOL 16 0-100/1000 LUX 0-10V
5 Functions
Figure4: Function curve.
Figure 5: Spectral sensitivity.

Technical User Guide
DOL 16 0-100/1000 LUX 0-10V www.dol-sensors.com 5
6 Maintenance
It is important to keep the light-sensitive area of the sensor free of dust to ensure correct measurements.
See Figure 1.
Clean the sensor with water and a brush without using:
• High-pressure cleaner
• Highly compressed air
• Solvents
• Corrosive/caustic agents
• Alcohol-based disinfectants
During cleaning and disinfection, the sensor should be removed and the sealing
plug for the cable should be mounted.
Alternatively, the sensor protective cap can be mounted. The sensor must be
placed with the light sensitive area of the sensor upwards during disinfection.
Do not bend the sensor as this would inflict permanent damage on the electronics of the sensor.

Technical User Guide
6www.dol-sensors.com DOL 16 0-100/1000 LUX 0-10V
7 Technical data
Unit Output 1 Output 2
Measurement range Lux 0-100 0-1000
Accuracy 5-100 Lux +/- 4%
at 0 – 40 oC (32 – 104 oF)
25-1000 Lux +/- 8%
at 0 – 40 oC (32 – 104
oF)
Output signal (lout) 0.1 V / 1 Lux 0.1 V / 10 Lux
Common
Time constant Sec. Typ. 2
max. 15
Supply voltage (Vsupply) V DC 11 - 30
Supply current mA 12 no load
55 max. load
Load Ω >500 – 10M
Recommended load kΩ >100
Output current mA 20 per output (current limited)
Output impedance Ω <1
Temperature, operation oC (oF) -40 – 60 (-40 – 140)
IP classification IP (NEMA) 67 (6)
Cable 2 m (6.6 feet) 4 x 0.33 mm2 (22 AWG)
Cable connection
(only M12 variant)
M12 female connector with 2 m (6.6 feet) 4 x 0.33 mm2
(22AWG) cable
Max. cable length m 100 0,82 mm2 (328 feet 18 AWG)
Shipping weight g (oz) 150 (5.3)
Measure, shipment mm (inch) 275 x 200 x 20 (11 x 8 x 0.8)
7.1 Dimensioned sketch
Dimensions In mm (inch).

Technical User Guide
DOL 16 0-100/1000 LUX 0-10V www.dol-sensors.com 7

Technical User Guide
dol-sensors a/s – Agro Food Park 15 – DK-8200 Aarhus N – T: [phone] – F: [phone] – www.dol-sensors.com
604145 • 2021-01-27 • en-US • Made in Denmark