dol sensors DOL 16 Manual

dol-sensors a/s Hedelund 4, Glyngøre 7870 Roslev Denmark Tel. [phone] Fax [phone] www.dol-sensors.com
DOL 16 0-50/1000 LUX 0-10V
Technical User Guide
For other language variants of
this document we refer to
www.dol-sensors.com or your
local dealer.

dol-sensors a/s Hedelund 4, Glyngøre 7870 Roslev Denmark Tel. [phone] Fax [phone] www.dol-sensors.com
EN –TECHNICALUSERGUIDE
PRODUCT DESCRIPTION
DOL 16 is a sensor designed to measure light intensity. It is intended for application in livestock houses but is also well suited for a number of
industrial applications.
Two variants of the sensor are available; one with a cable, and one with M12-connector/cable.
MAINTENANCE
IMPORTANT
It is important to keep the light-sensitive area of the sensor free of dust to ensure correct measurements. See Figure 1.
Apart from this, the product does not require any maintenance.
Do not expose the sensor to strong solvents as they may damage its surface and affect measurements.
Avoid using solvents such as acetone and alcohol.
Do not bend the sensor as this would inflict permanent damage on the electronics of the sensor.
Dol-sensors reserve the right to change this document and the product herein described without further notice.
Figure 1: DOL 16
LED/LIGHT PROTOCOLL
LED
Status
Green
Red
ON
Operation OK
ON
Connection error
Load < 500 Ω
Flash
Sensor defect
Over/under voltage alarm
Overload
Output Voltage
Figure 2: Mounting
Figure 3: Functional graph
Light-sensitive area
1/4 of the width of the livestock house
Place the sensor in
front of an inlet that
opens first, in order to
minimise the build-up of
dust on the sensor.

dol-sensors a/s Hedelund 4, Glyngøre 7870 Roslev Denmark Tel. [phone] Fax [phone] www.dol-sensors.com
EN–TECHNICALUSERGUIDE
INSTALLATION
For optimum mounting of the sensor, use a mounting clips.
The sensor should be placed in a position which is representative of the light level in the house –the light-sensitive area of the sensor is shown in
Figure 1. Sunlight from the outside and objects obstructing incident light should be taken into account.
Examples of mounting are shown in Figure 2.
When demounting variant with M12 connector, the included plug must be mounted.
Figure 4: Connection
If 1:1 compliance with the L 182/19 standard is desired, measurements according to the standard and an adaptation to the output of the DOL 16
sensor with the chosen position must be carried out.
IN DUSTY ENVIRONMENTS, THE SENSOR SHOULD BE PLACED IN A POSITION WHICH ALLOWS FOR EASY CLEANING AT REGULAR
INTERVALS.
TECHNICAL DATA
Output 1
Output 2
Measuring range
0 –50 Lux
0 -1000 Lux
Accuracy
2 -50 Lux 4 %
at 0 - 40 °C(32 °F –104 °F)
25 -1000 Lux 8 %
at 0 - 40 °C(32 °F –104 °F)
Output signal (Iout)
0.2V / 1 Lux
0.1V / 10Lux
Common
Time constant
Typ. 2 Sec.
Max. 15 Sec.
Supply Voltage (Vsupply)
11 –30 V DC
Supply Current
12 mA no load
55 mA max. load
Load
>500 Ω - < 10 MΩ
Recommended load
≥ 100 kΩ
Output current
20 mA per output (current limited)
Output impedence
< 1 Ω
Temperature, operation
- 40 °C –60 °C(-40°F - 140°F)
IP classification
IP 67(NEMA 6)
Cable
2 m (6.6 feet) 4 x 0.33mm2(22AWG) cable
Cable connecting (only M12 variant)
M12 female connector with 2m (6.6 feet) 4 x 0.33mm2 (22AWG) cable
Max. cable length
100 m 0.82 mm2(328 feet 18AWG)
Shipment weight
150 g (5.3oz)
Measure, shipment
275 × 200 × 20 mm (11 × 8 × 0.8 inch)

2016.06.01 • 604132 • 16.15 • EN
dol-sensors a/s Hedelund 4, Glyngøre 7870 Roslev Denmark Tel. [phone] Fax [phone] www.dol-sensors.com
EN–TECHNICALUSERGUIDE
SPECTRAL SENSITIVITY
Figure 5: Spectral sensitivity
DIMENSIONS
Figure 6: Dimensions mm (inch)
DOL 16
CIE Human Eye