Dolphin Supreme M4 User manual

1English
by
DOLPHIN SUPREME M4
EN
FR
IT
SP
DEU
User Instructions
Guide d’utilisation
Istruzioni per l’uso
Instrucciones para el Usuario
Bedienungsanweisungen
8151146 Ver. 02, 2/2011

English

1English
What You’ll Find Inside the Box
Part X Comment
Base frame for filter elements 2
Ultra-fine filter 4 filters
Bag for filters storage 1
Spring filter 4 filters
“S” clip 4
Power supply unit 1
Dolphin pool cleaner 1
Caddy kit 1
Optional components available on request from your Dolphin distributor
Power supply unit
Dolphin pool cleaner
Filter and cartridges
Section 1 - Description of Main Components
1. Filters
Dual-level filtration system.
Spring filter + base frame
For dirty pools with large debris such as
leaves etc. – Useful for beginning of season.
Ultra-fine filter cartridge + base frame
For day-to-day use.
Factory default.
2. Brushes
There are three types of optional brushes, each designed to provide optimal traction on different pool surfaces.
Only one type set is provided with your Dolphin.
PVC Brush
For concrete, PVC, fiberglass and liner.
Combined Brush
For rough ceramic surface and mosaic tiles.
Wonder Brush
For smooth ceramics.

2
English
3. Power supply unit
Digital, “Switch-Mode” power supply:
Input - 100-250 AC Volts•
50-60 Hertz•
180 Watt•
Output - 30 VDC•
IP 54•
Section 2 – Dolphin Operation
Part 1 – Preparing the Dolphin pool cleaner for use
A. Assemble the Caddy kit – you will find the instructions in a separate document
B. Adjusting the handle float angle
The Handle angle must be adjusted to determine the speed that the Dolphin advances along the water-line.
1. Press the latch down and hold in position.
2. Move the handle to the required position
and release the latch to lock the Handle in place.
Normal advance
More efficient cleaning action on water-line.
Fast advance
Fast speed – For faster but less efficient cleaning
action on water-line.
ON
On/Off
switch

3English
C. Laying out the cable
Unwind minimal required cable to cover the entire pool size, straight the cable along the pool side.
Make sure there are no twists or kinks.
Part 2 - Into the water
Inserting the Dolphin into the pool.
Note: When using the combined brushes or Wonder brushes, gently squeeze the Wonder brush material until it is totally wet.
Place your Dolphin into the pool and release it.
Use only the original supplied power supply unit.
The power supply unit is splash proof – do not immerse it in water.
Unplug the power supply unit before any servicing activity.
Do not plug the power supply unit in before placing the pool cleaner in the water.
Ensure the mains outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI).
Important: DO NOT enter the swimming pool while the pool cleaner is working.
3 Meters
10 feet
Optional Swivel

4
English
Turning the Dolphin ON
Part 3 - Taking the Dolphin out of the water
Unplug power supply before any servicing activity.
If the Dolphin has not finished its cycle, turn off the power1.
supply unit and unplug the mains.
Pull the floating cable gently until the Dolphin has risen to2.
the surface, then lift by the handle.
Plug the floating cable from the1.
Dolphin into the power supply unit.
Plug the electrical cable from the power2.
supply unit into the mains.
Press on the ON/OFF switch.3.
The Dolphin will now start to work.4.
Note: If your model includes the remote control unit, please refer to the included instruction leaflet.
Important: Do NOT lift the Dolphin from the water by its cable.
Floating cable
ON
On/Off
switch
Important: DO NOT enter the swimming pool while the pool cleaner is working.

5English
Section 3 - Routine Maintenance
Part 1 - Extracting and cleaning the filter elements
Unplug power supply before any servicing activity.
Reassemble
Insert the locating tabs at the bottom of the filter element into their groves on
the base frame, then close the “S” clip.
Locating tab
Locating tab groove
2 3
1

6
English
Reinstall the filters according to the diagram
DO NOT FORCE THE FILTERS INTO PLACE.
Part 2 - Dismantling and cleaning the impeller
Unplug power supply before any servicing activity.
Dismantle the impeller cover and
clean around the impeller housing,
then reassemble.
Grooved end fitting Octagonal end fitting
Important: Where applicable, you must reset the full filter bag indicator on the power supply unit.
Recommendation: Rinse all brushes with clean water after each cleaning cycle.
Coil the cable and store in dry cool area – preferably on the Caddy if available.
Do NOT store the Dolphin exposed to direct sunlight.
Do NOT store the Dolphin exposed to excessive heat.
Do NOT store the Dolphin exposed to frost.
Part 3 - Storage instructions
21
Philips head

7English
Helpful hints for better scanning of your pool
The floats can be moved side-ways along the handle groove housings.
To Move the floats in their handle housing grooves
There are three possible float configurations:
Floats default position If turns while scanning less than 90º,
pull out left float.
If turns while scanning more than 90º,
pull out right float.
Release Button
Push float outwards.1.
To move the floats back to their original2.
position, while pressing the release
button on the base of the float,
push the float back.

8
English
Troubleshooting Guide
Before contacting your Dolphin distributor please read through this guide.
The pool water condition must be within the following parameters:
PH: 7.0 – 7.8 NaCl: Max 5,000 ppm
Temperature: 6˚C(43˚F) to 34˚C(93˚F) Chlorine: Max 4 ppm
Symptom Solution
Cable twisting or cable coils up Check for any obstruction in the pool
Remove excess cable from the pool
Make sure filter cartridge is clean
Straighten cable and lay it in the sun periodically
Dolphin is moving in circles or does not reach all pool areas Check for foreign objects in moving parts
Make sure filter cartridge is clean and well mounted and that the
filter doors are closed
Make sure that there is enough cable laid out to cover the
whole pool
Before using the Dolphin at the beginning of the season you
should brush any algae from the floor and walls of the pool
Adjust the diagonal angle of the handle
Dolphin is not traveling sideways on walls
Dolphin does not climb walls Make sure the filter cartridge is clean
If using the Dolphin at the beginning of the season, use the
spring cartridge
Check if brushes are suitable for pool coating and replace them
if necessary
Check if brushes are worn and replace them if necessary
Make sure the impeller area is clean
When applicable: Check that the RCU is set for climbing
Dolphin not sinking Make sure the Wonder brushes or the combined brushes are
soaked in water
Dolphin disengaging from wall at water line If Dolphin climbs too high consult your Dolphin distributor
RCU is not working Check if the batteries need replacing
Motor is not working Check if the impeller is blocked
Check if the drive system is blocked
Electrical problem (power supply), check power source
If power source is in order, please contact your Dolphin
distributor
Additional troubleshooting is available at our Website:
www.maytronics.com