domi outdoor living LGMF1618 User manual

10' × 10' Metal Patio Gazebo
ASSEMBLY MANUAL
MODEL#: LGMF1618
Missing part? Damaged? Contact us via email at
[e-mail]
www.domioutdoorliving.com
©Copyright 2022-2024 domi LLC. I All Rights Reserved.

Pole Beam
Beam Corner Roof Bar
Corner Roof Bar Connector Roof Bar
Solidfying Bar Finishing Bar
Finishing Bar Finishing Bar
Finishing BarRoof Panel
Roof Panel Roof Panel
Roof Panel Roof Panel

Roof Panel Roof Panel
Roof Panel Net Frame
Base Bracket Union Bar
Corner
Solidifying Bar
Inside Roof
Connector
Outside Roof
Connector
J-Hook Bracket Bracket Bracket
Joint Cover Hook Spacer
Corner
Solidifying Bar
Bracket Corner Cover Finishing End Finishing End
Solid Sidewall Mosquito
Sidewall
Plastic
Bracket
Plastic
Bracket
Bracket
Joint Cover

Plastic
Bracket Plastic Bracket Plastic Bracket

(1) Attach 2 Part #B1 to Part #A
with 4 Bolts #8.
(2) Attach 2 Part #B2 to Part #A with
4 Bolts #6.
(3) Attach Part #B to Part #A with
3 Bolts #8.
(4) Repeat the above procedures to assemble the other 3 Part #A.

(1) Insert Part #C2 into Part #C1
and secure with 3 Bolts #8.
(2) Insert the other side of
Part #C2 into Part #C and
secure with 3 Bolts #8.
(3) Connect Part #C1 and
Part #C through Part #C2.
(4) Insert Part #X into the beam.
(5) Secure the bottom of Part #X
and Part #C/C1 with 3 Bolts #8.
(6) Repeat the above procedures to assemble the other Part #C
and Part #C1.

(1) Connect Part #C/C1 to Part #A with 8 Bolts #4.(From Outside)
(2) Repeat the above procedures to assemble the other 3 corners.
Please don't tighten all bolts.
!

(1) Connect Part #C/C1 to Part #A with 4 Bolts #8.(From Inside)
(2) Repeat the above procedures to assemble the other 3 corners.
Please don't tighten all bolts.
!

(1)Affix Part #R and Part #R1 to the frame with 8 Bolts #8.
(2) Repeat the above procedures to assemble the other 3 corners.
Tighten all the bolts.
!

(1) Cover the corner with Part #X1.
(2) Secure with 2 Self-tapping Screws #3.
(from top to bottom)
(3) Secure with 2 Self-tapping Screws #3.
(from bottom to top)
(4) Repeat the above procedures to assemble the other 3 corners.

Assemble the 4 Corner Roof Bars:
(1) Connect Part #E1 and Part #E with 2 Bolts #8 .
(2) Attach Part #U to Part #E with Bolt #8 .
(3) Repeat the above procedures to assemble the other
3 corner roof bars.

Please have a freestanding ladder ready at the center of the gazebo.
(1) Place 4 Part #E1 on the 4 corners of Part #S.
Secure with 8 Bolts #8 (from bottom to top)
ATTENTION: You can also finish
this step on the ground and then
lift 4 corner roof bars and inside
roof connector to the top together.
(Need 2 people and 2 ladders)
(2) Place 4 Part #E on 4 Part #A;
Secure with 8 Bolts #8.
Outside View
Outside View

(1) Attach Part #U1 to Part #E2 with Bolt #7.
(2) Repeat the above procedures to assemble the other 3 roof bars.

(1) Place Part #E2 on part #S.
Secure with Bolt #8 (from bottom to top).
(2) Connect Part #E2 and the Assembled Beam(C&C1) with part #U1.
Secure with 2 Bolts #8 .
(3) Repeat the above procedures to assemble the other 3 sides.
Outside View
Inside View
C1
C1
C1
C1
C
C
C
C

Secure Part #T to Part #S and Part #S1.
ATTENTION: The holes of Part #S and Part #S1 need to be aligned,
on the same vertical line.
Outside View

(1) Insert Part #U3 into 2 Part #F.
(2) Attach Part #F to the Part #E2
with 1 Bolt #7 and 2 Blots #8.
(3) Repeat the above procedures to assemble the other 3 sides.
Inside View
Outside View

(1) Insert Part #U2 into 2 Part #F.
(2) Secure with 2 Bolts #8.
(3) Secure them to Part #E with Bolt #8.
(4) Repeat the above procedures to assemble the other 3 sides.
Inside View