Domus BOLT-120-TRIO User manual

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: [phone] | Fax: [phone]
enquiries@domuslighng.com.au | www.domuslighng.com.au
Installaon Manual
Note: -The lamp must be installed by professional electrician
 -Ensurethepowersupplyisswitchedobeforengthisproduct
-Do not touch the lamp when in use
-Keepawayfromhotsteamandcorrosivegas
1.Turn off power at mains supply. The unit MUST be
isolated from the supply before installaon.
7
7.Turn on the power supply.
6
6.Push caps back to Baen
Base unl it catch the spring connector B .
spring connector B
3
3 Fix the baen base onto the required place
with screws.
4
4.Individually connect the Live wire,Neutral wire and Earth wire into the terminal block; Set the driver switch
to desired seng,and default driver seng is “I” mode.
Terminal block
Input cable
1mm
1mm
3x (1.0-4.0mm2)
20
Dual Power Switch:
I-High power
O-Low Power L
N
E
2,Aer unpacking and taking out the baen, pull caps as direcon showed to posion as Picture A showed;
then pull off LED MODULE from BATTEN BASE and unfasten terminal A between driver and LED MODULE.
Picture A
Terminal A
BATTEN BASE
DRIVER
LED MODULE
5
5.Fasten terminal A between driver and LED MODULE；Snap LED MODULE back to BATTEN BASE;
Make sure all Spring Connector A are in place to securely hold LED MODULE to BATTEN BASE.
Terminal A
Spring Connector A
Surface Mounted
BOLT-120
Voltage: 240V~ Lumen (±10%): (21W) Warm White 3000K - 1665lm
(42W) Warm White 3000K - 3420lm
(21W) Neutral White 4000K - 1850lm
(42W) Neutral White 4000K - 3800lm
(21W) White 5700K - 1850lm
(42W) White 5700K - 3800lm
Dimmable: No
Power: 21/42W Beam Angle: 120° CCT: 3000K, 4000K, 5000K
IP Rang: 44 CRI: ≥80 Lifespan: 40,000hrs
Frequency: 50Hz Power Factor: 0.9C Current: 236mA
Weight: 1.9kg
BOLT-120-TRIO Date:11/2019
Order Code Product Code Descripon
66003 BOLT-120-TRIO (21W) Warm White 3000K - 1665lm
(42W) Warm White 3000K - 3420lm
(21W) Neutral White 4000K - 1850lm
(42W) Neutral White 4000K - 3800lm
(21W) White 5700K - 1850lm
(42W) White 5700K - 3800lm
Thank you for purchasing your new LED BOLT Baen, Please take the me to read and understand the instrucon
sheet below. Failure to do so may void warranty.
Note: The light source of this luminaire is not replaceable; When the light source reaches its end of life, the
whole luminaire shall be replaced.

29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: [phone] | Fax: [phone]
enquiries@domuslighng.com.au | www.domuslighng.com.au
Installaon Manual
Note: -The lamp must be installed by professional electrician
 -Ensurethepowersupplyisswitchedobeforengthisproduct
-Do not touch the lamp when in use
-Keepawayfromhotsteamandcorrosivegas
1.Turn off power at mains supply. The unit MUST be
isolated from the supply before installaon.
7
7.Turn on the power supply.
6
6.Push caps back to Baen
Base unl it catch the spring connector B .
spring connector B
3
3 Fix the baen base onto the required place
with screws.
4
4.Individually connect the Live wire,Neutral wire and Earth wire into the terminal block; Set the driver switch
to desired seng,and default driver seng is “I” mode.
Terminal block
Input cable
1mm
1mm
3x (1.0-4.0mm2)
20
Dual Power Switch:
I-High power
O-Low Power L
N
E
2,Aer unpacking and taking out the baen, pull caps as direcon showed to posion as Picture A showed;
then pull off LED MODULE from BATTEN BASE and unfasten terminal A between driver and LED MODULE.
Picture A
Terminal A
BATTEN BASE
DRIVER
LED MODULE
5
5.Fasten terminal A between driver and LED MODULE；Snap LED MODULE back to BATTEN BASE;
Make sure all Spring Connector A are in place to securely hold LED MODULE to BATTEN BASE.
Terminal A
Spring Connector A
Surface Mounted
Suspended
31 2
Warning:
If the product is not installed as per the Installaon Manual, then the warranty and liability for the product will
be voided.
Date:11/2019