Donco PRINCETON STAIR BUNK 2204 User manual

#2204 PRINCETON STAIR BUNK
SLATE - GREY
1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not
remove warning label from bed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches (127mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on the upper bunk.
6. Periodicall, check and ensure that the guardrail, ladder, and other components are in their proper position,
free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Always use guardrail on both long sides of the upper bunk. If bunk bed will be placed next to the wall, the
guardrail the runs the full length of the bed should be place against the wall to prevent entrapment between
the bed and wall.
12. The use of water or sleep flotation mattresses is prohibited.
13. Keep these instruction for future reference.
SAFETY WARNINGS
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not
designed for use with the bed ; for example, but not limited to, hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress, foundation and desk combined which is 74 - 75 inches long and 37 1
2- 38 1 2inches wide on
upper bunk.
Ensure thickness of mattress and foundation combined does not exceed81
2inches and mattress and is at
least 5 inches below edge of guardrails.
Replacement parts, may be obtained from any Donco dealer or directly from us at the below address.
DONCO TRADING COMPANY
Fort Worth, Texas 76140

3
5
4
NO. DESCRIPTION Q'ty NO. DESCRIPTION Q'ty
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY Page 1/11
LEFT ASSEMBLY RIGHT ASSEMBLY
Princeton Section Assembly Hardware
2pcs
14pcs
1pc
Furniture Screw (Ø1/4x70mm)
Furniture Screw (Ø1/4x50mm)
Allen Key
11 12
10 6pcs
Screw (Ø4x30mm)
Knob
4pcs
Bolt (Ø4x45mm)
4pcs

# A
Chest
1 PC
# B
Outside Princeton Section Panel
1 PC
# C
Inside Princeton Section Panel
1 PC
# D
# E
# M
Small Step
Large Step
Princeton Section Back Panel
1 PC
1 PC
Outside Bunk Bed Section Panel
# G
1 PC
Inside Bunk Bed Section Panel
# H
1 PC
1 PC
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY Page 2/11
Box A
Lower Mattress Support Rail
# I
2 PCS
Slat Roll
# L
2 SETS
Upper Bunk Safety Rail
# N
4 PCS
Upper Mattress Support Rail
# J
2 PCS
Box C
Box D
# F
2 PCS
Vertical Support Bar
Top Rail
# K
2 PCS
Box B

ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY Page 3/11
Place the handle in front of the drawer panel and insert the screw into the pre-drilled holes.
Tighten it with screwdriver (not provided).
12 11
K
B
G
K10
10
10
BG

Page 4/11
LEFT ASSEMBLY RIGHT ASSEMBLY
A A
AA
A
B
B
B
1. Open the Chest Box and position the Chest (A) with the Drawer Fronts opening either to the
LEFT (Steps on the Left End of Bunk Bed) or to the RIGHT (Steps on Right End of the Bunk
Bed).
2. Position the Outside Princeton Section Panel (B) so that the opening in the Panel is in Front
of the Chest Drawer Fronts.
3. Slide the Outside Princeton Section Panel (B) up to and flush with the Front of the Chest
(A). Align the holes through the Outside Princeton Section Panel (B) with the holes in the edge
of the Chest Top ( Top Step).
4. Insert 2- Furniture Screws (6) from the outside of the Panel (B) and into the Chest Top (A)
and tighten by using the Allen Key (4) provided.
5
5
4
5
5
4
5
5
4
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 5/11
LEFT ASSEMBLY RIGHT ASSEMBLY
AA
B
B
5. Position the Inside Princeton Section Panel (C) with the back side of the Chest (A).
6. Slide the Inside Princeton Section Panel (C) up to and flush with the Back of the Chest (A).
Align the holes through the Inside Princeton Section Panel (C) with the holes in the edge of the
Chest Top ( Top Step).
7. Insert 2- Furniture Screws (6) from the outside of the Panel (B) and into the Chest Top (A)
and tighten by using the Allen Key (4) provided.
C
C
B
C
A
4
5
4
5
5
4
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 6/11
LEFT ASSEMBLY RIGHT ASSEMBLY
8. Position the Princeton Section Back Panel (M) in-between the Inside and Outside Princeton
Section End Panels (B&C). Insert 2- Furniture Screws (6) from the outside of both the Inside
and Outside Panels (B&C) and into the Back Panel (M) and tighten by using the Allen Key (4)
provided.
9. Position the Small and Large Steps (D&E) in-between the Inside and Outside Princeton
Section End Panels (B&C) and into the Small and Large Steps (D&E) and tighten by using the
Allen Key (4) provided.
- NOTE: The Large Step (E) is reversible and is notched on one front corner so that it can if
around the Post in both Left and Right Princeton configurations.
10. Princeton Section is now Fully Assembled.
M
C
B
D
E
MB
D
E
A
MM
B
B
C
D
E
A
C
D
E
5
55
45
3
3
4
5
5
55
5
5
55
5
5
4
43
3
5
5
4
43
3
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 7/11
1
2
7
NO. DESCRIPTION Q'ty NO. DESCRIPTION Q'ty
HARDWARE LIST
1. Insert Wooden Dowels (9) into the ends of all of the Upper Bed safety Rails.
2. Insert Wooden Dowels (9) into the ends of all of the Upper & Lower Support Rails.
3
5
6
8
9
10
N x 4
8pcs
Machine Screw (Ø1/4x80mm)
16pcs
Half Moon (Ø1/4)
4pcs
Furniture Screw (Ø1/4x70mm)
4pcs
Furniture Screw (Ø1/4x50mm)
8pcs
Machine Screw (Ø1/4x60mm)
12pcs
Female Half Moon (Ø1/4x15mm)
12pcs
Machine Screw (Ø1/4x32mm)
16pcs
Wood Dowel (Ø10x40mm)
16pcs
Screw (Ø4x30mm)
9
9
I
J
9
9
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 8/11
LEFT ASSEMBLY RIGHT ASSEMBLY
4. Align the Wooden Dowels (9) in the end of the Lower Mattress Support Rails (I) with the
holes in the Outside Bunk Bed End Panel (G) and the Inside Bunk Bed End Panel (H).
5. Insert The Dowel (9) in the Lower Mattress Support Rails (I) into the hole in the Inside End
Panel (H).
6. Insert 2-" Half Moon" Nuts into the large holes on the inside of the Lower Mattress Support
Rails (I).
7. Insert 2- Machine Screws (1) into the holes on the outside of the End Panel (H) and into the
Half Moon Nuts (2) in the Lower Mattress Support Rails (I).
8. Tighten by using the Allen Key (4) provided.
9. Repeat these steps for the other end of this Mattress Support Rail (I) and End Panel (G).
10. Repeat these steps for the other Lower Mattress Support Rail (I) with both End Panels
(G&H).
11. Repeat all these steps for the Upper Bunk Mattress Support Rails (J).
3. IMPORTANT: Make sure that the access opening for the upper Bunk Bed on the Inside
Bunk Bed Panel is toward the Back Side/ Wall Side of the Bed, as you would face it when fully
assembled.
H
G
I
I
G
H
I
I
2
2
2
2
6
6
6
6
2
2
2
2
11
11
46
62
41
12
2
2
14
1
9
2
2
1
12
2
11
2
2
2
2
66
66
9
9
I
I
J
J
H
H
G
G
46
62
9
2
2
6
6
2
2
14
1
9
41
12
9
2
2
6
6
2
2
2
2
11
1
1
2
1
12
2
1
1
2
2
2
2
66
6
6
2
I
I
J
J
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 9/11
LEFT ASSEMBLY RIGHT ASSEMBLY
12. Align the Wooden Dowels (9) in the end of the Upper Bunk Safety Rails (N) with the holes
in the Outside Bunk Bed End Panel (G) and the Inside Bunk Bed End Panel (H).
13. Insert the Wooden Dowel (9) in the Upper Bunk Safety Rails (N) into the hole in the Inside
End Panel (H).
14. Insert 1-Furniture Screws (3) into the hole on the outside of the End Panel (H) and into the
end of the Safety Rail (N).
15. Tighten by using the Allen Key (4) provided.
16. Repeat these steps for the other end of this Upper Bunk Safety Rails (N) and End Panel
(G).
17. Repeat all these steps for the three other Bunk Safety Rails (N) with both End Panels
(G&H).
18. Align the 3 - holes in the Vertical Support Bar (F) with the holes in the Upper Bunk Bed
Mattress and Safety Rails (J&N).
19. Insert Machine Screw (7) through the Support Bar and the Bed / Safety Rail and into the
Female Hex Nut (8).
20. Tighten with the Allen Key (4) provided.
21. Repeat all steps with the other Support Bar (F) on the opposite side of the Upper Bunk
Bed.
G
G
H
H
II
J
J
II
J
J
N
N
F
N
N
F
G
G
H
II
J
J
II
J
J
N
N
F
N
N
F
55
7
8
7
5
5
7
7
8
8
N
9
5
5
4
F
N9
9
N
9
3
3
4
33
3
3
8
7
7
8
7
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 10/11
LEFT ASSEMBLY RIGHT ASSEMBLY
22. Place the Princeton Section in its preferred final location in the room.
23. Align the Bunk Bed section with the Princeton Section.
24. Slide the Bunk Bed Inner End Panel up to and flush with the Princeton Section.
25. Align the 3-holes vertically along the Rear Inside Panel Corner Posts (flushed together).
26. Insert Machine Screw (7) through the two posts and into the Female Hex Nut (8).
27. Tighten with the Allen Key (4) provided.
28. Repeat all steps with the holes vertically along the Front Inside Panel Corner Post (flushed together).
29. Install the Slat Roll (L) in the Upper Bunk Bed by rolling it out into position on the Support Cleat.
30. Align the outside edge of the first slat with the end of the Support Cleat on the Inside of the Mattress Support Rail (I).
This aligns the first slat at the proper distance from the Bunk End Panel.
31. The outside edge of the last slat should be flush with the end of the Mattress Rail Support Cleat at the other end of the
Mattress Rail as well.
32. Insert the Wood Screw (10) into the holes in the slats and tighten.
33. Repeat all steps for the Slat Roll (L) in the Lower Bunk Bed.
Back side
Back side
Back side
Back side
7
8
7
8
7
8
7
8
7
8
7
8
7
8
7
8
7
84
4
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY

Page 11/11
LEFT ASSEMBLY RIGHT ASSEMBLY
10
10
10
SIDE - RAIL
SLAT ROLL
10
10
10
10
10 10
10
10
10
10
ASSEMBLY INSTRUCTIONS
# 2204 PRINCETON STAIR BUNK - SLATE GREY