Dorel Asia DA1010BB-1 User manual

DA1010BB-1
DA1010BB-2
(TAKEN FROM CARTON)
_____________________________________
Date of purchase:
_______ / _______ / _______
0-65857-17149-5
THIS INSTRUCTION BOOKLET
CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
Lot number:
TWIN BUNK BED UPC CODE:
NOTE:
0-65857-17148-8
DOREL ASIA
Model No:
DO NOT RETURN PRODUCT TO THE
STORE.
If a part is missing or damaged, contact our
customer service department. We will replace
the part FREE of charge.
Tel #: [phone]
E-Mail: [email protected]
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

*
*
*
*
*
*
MAXIMUM WEIGHT CAPACITY: 165 LBS (75KGS) PER LEVEL.
*
*
*
*
*
*
*
*
*
*
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE
BED.
DO NOT USE SUBSTITUTE PARTS. CONTACT CUSTOMER SERVICE FOR REPLACEMENT
PARTS.
USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD
USING THE UPPER BUNK.
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK
BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL
LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT
ENTRAPMENT BETWEEN THE BED AND WALL (APPLICABLE FOR BUNK BEDS WITH
FULL LENGTH GUARDRAILS ON ONE SIDE).
ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
Montreal, Quebec
Canada, H1G 3L1
USE ONLY COIL SPRING MATTRESSES ON BOTH THE UPPER AND LOWER BUNKS.
FAILURE TO DO SO CAN RESULT IN INJURY.
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON
UPPER AND ON LOWER BUNKS. ENSURE THICKNESS OF MATTRESS DOES NOT
EXCEED 6". SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE
UPPER EDGE OF GUARDRAILS.
STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE
BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT
NOT LIMITED TO HOOKS, BELTS AND JUMP ROPES.
ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR
BOTH, TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK
END STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM
BED.
THE MATTRESS PLATFORM IS DESIGNED TO SUPPORT A MATTRESS WITHOUT THE
NEED FOR A POSTURE BOARD OR BOX SPRING.
*
E-MAIL: [email protected]
WARNING
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service
representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product
model number, color and a detailed description of the part.
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100

*
*
*
*
*
*
*
*
*
ESTIMATED ASSEMBLY TIME 60 MINUTES.
Check bolts/screws periodically and tighten them if necessary.
Dorel warrants its product to be free from defects in material and workmanship and agrees to
remedy any such defect. This warranty covers 1 year from the date of original purchase. This
warranty is valid only upon presentation of proof of purchase. This is solely limited to the repair
or replacement of defective furniture components and no assembly labor is included. This
warranty does not apply to any product which has been improperly assembled, subjected to
misuse or abuse or which has been altered or repaired in any way. This warranty gives you
specific legal rights and you may also have other rights which vary from State to State.
READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH
STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS
ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN
RESULT IN INJURY.
MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A
SMOOTH SOFT SURFACE.
ASSEMBLY WILL REQUIRE TWO PEOPLE.
PHILLIPS SCREWDRIVER (NOT INCLUDED) IS REQUIRED.
CAUTION: ADULT ASSEMBLY REQUIRED.
MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
MAINTENANCE
LIMITED WARRANTY
CARE AND CLEANING
Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage
finish. Excessive exposure to sunlight and extreme changes in temperature and moisture can
damage wood furniture.
A RUBBER MALLET (NOT INCLUDED) IS RECOMMENDED TO FACILITATE ASSEMBLY.
BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG
TEENAGERS.
NOTES
WARNING: Should this product become
damaged, and/or components are broken or
missing, DO NOT USE.

1 2
3 4
5 6
7 8
910
WOOD DOWEL
4 PCS
∅19mm x 95mm
WOOD JOINT CONNECTOR (4mm HEX HEAD)
22 PCS
WOOD DOWEL
30 PCS
∅10mm x 50mm
FLAT HEAD WOOD SCREW
24 PCS
∅6.5mm x 100mm
∅4mm x 35mm
DA1010BB-1 / DA1010BB-2
TWIN BUNK BED
JOINT CONNECTOR (4mm HEX HEAD)
16 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD)
14 PCS
∅1/4" x 100mm
∅6.5mm x 48mm
HARDWARELIST
ALLEN KEY
1 PC
CAP
4 PCS
∅4mm x 30mm
FLAT HEAD WOOD SCREW
6 PCS
BARREL NUT
16 PCS
∅11.8mm x 15mm

A B C
D E F
HEADBOARD
2 PCS
BOTTOM POST
2 PCS
BOTTOM POST
2 PCS
TWIN BUNK BED
TOP POST
2 PCS
TOP POST
1 PC
TOP POST
1 PC
PARTS LIST
DA1010BB-1 / DA1010BB-2

G H I
J K L
M N O
P Q R
S
TWIN BUNK BED
PARTS LIST
FOOTBOARD
2 PCS
TOP SIDE RAIL (WITH 3 HOLES)
1 PC
BOTTOM SIDE RAIL (WITH 2 HOLES)
1 PC
DA1010BB-1 / DA1010BB-2
TOP SIDE RAIL (WITH 1
HOLE)
1 PC
BOTTOM SIDE RAIL (WITH NO
HOLES)
1 PC
SLAT
12 PCS
SHORT LADDER END
1 PC
LONG GUARDRAIL
2 PCS
SHORT GUARDRAIL
2 PCS
LADDER STEP
4 PCS
GUARDRAIL LEG
2 PCS
LONG LADDER END
1 PC
SLAT
4 PCS

TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
Insert wood dowels (7) into both ends of headboard (F).
Attach top posts (A & B) to the headboard (F) with wood joint connector (3) using
Allen key (9).
STEP 1

STEP 2
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
Repeat the previous step to assemble the footboards (G) and other headboard (F).
Be sure to attach the bottom posts (D & E) to the footboard (G) and top posts (C & A)
to the headboard (F).
NOTE: Be sure to use headboard (F) with the label attached to it between top posts (A)
and (C). See illustration for label orientation.
Label

TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
Attach footboards (G) to the bottom side rails (I and K) with joint connectors (1) and
barrel nuts (8) using Allen key (9).
Note: This is the lower bunk.
STEP 3
I
K
Holes
1
1
9
8
8
8
8
I
K
Holes
1
1
9
8
8
8
8
G
G

STEP 4
Insert barrel nuts (8) to the top side rails (H and J).
Insert wood dowels (7) into each end of the long guardrails (M).
Attach top side rails (H and J) to the top posts (A, B and C) as shown above with
joint connectors (1) and barrel nuts (8). Attach long guardrails (M) to the top posts
(A & B) with wood joint connectors (3) using Allen key (9).
Note: This is the upper bunk.
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
3
M
3
M
3
M

STEP 5
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
Insert slats (S) into the center slots of the bottom side rails (I and K).
NOTE: Once inserted, there should be three empty spaces left on each side.

STEP 6
Insert slats (L) into remaining holes on the bottom side rails (I and K) on the lower
bunk.
Secure salts (L) to the bottom side rails (I and K) with flat head wood screws (4)
using a Phillips head screw driver (not included).
Repeat step 5 and 6 to attach slats (S and L) to the upper bunk.
NOTE: Slats (S and L) will be placed between two wooden blocks.
NOTE: If you notice that any slats (L) are not perfectly flat, be sure to assemble them
so that slats (L) curves up in the middle and down on the ends.
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2

STEP 7
Insert wood dowels (7) in the ends of short guardrails (N). Attach short guardrails (N)
to the top post (A) with wood joint connectors (3). Attach the guardrail leg (R) to the
short guardrails (N) and top side rail (H) with flat head wood screws (5). Attach
another guardrail leg (R) to long guard rails (M) and top side rail (J) with flat head
wood screws (5) using a Phillips head screwdriver (not included).
Place four wood dowels (6) into the holes in the bottom posts (D and E). Stack the
top bunk onto the bottom bunk with the help of another person.
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6

STEP 8
To assemble the ladder, insert wood dowels (7) into the end of the ladder steps (Q).
Attach long ladder end (O) and short ladder end (P) to ladder steps (Q) with wood
joint connectors (2) and Allen key (9).
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
8 PCS
2
78 PCS

STEP 9
Attach the ladder to the short guardrails (N), top side rail (H) and bottom side rail (I)
with wood joint connectors (2) as shown.
NOTE: If slat (L) is covering the ladder mounting holes, remove slat (L) and replace
after the ladder is attached.
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
N
H
I
26PCS
2

With the help of another person, remove the top bunk from the lower bunk.
Note: Switching the headboards will allow the two single beds to be identical (the
headboards will have taller posts and the footboards will have the shorter posts).
TWIN BUNK BED
Re-assemble the headboards (with tall posts) and footboards (with short posts) to
side rails.
DA1010BB-1 / DA1010BB-2
Instructions for converting the bunk bed into two twin beds
Disassemble the side rails from all headboards (top and lower bunks).
Remove the ladder and all the guardrails.
10 CAP - 4PCS
10

That's it! You've finished assembling your bunk bed.
TWIN BUNK BED
DA1010BB-1 / DA1010BB-2
CAUTION: This unit is intended for use only with the products
and/or maximum weights indicated. Use with other products
and/or products heavier than the maximum weights indicated may
result in instability or cause possible injury.
DO NOT ALLOW HORSEPLAY ON
OR UNDER THE BED AND
PROHIBIT JUMPING ON THE
BED.
DO NOT ALLOW CHILDREN UNDER 6
YEARS OF AGE TO USE THE UPPER
BUNK. BED IS DESIGNED FOR
CHILDREN RANGING FROM 6 YEARS OF
AGE TO YOUNG TEENAGERS.
USE ONLY COIL SPRING
MATTRESSES ON BOTH THE UPPER
AND LOWER BUNKS. FAILURE TO DO
SO CAN RESULT IN INJURY.
USE ONLY MATTRESSES WHICH ARE
74"-75" LONG AND 37 1/2" - 38 1/2"
WIDE ON UPPER AND ON LOWER
BUNKS. ENSURE THICKNESS OF
MATTRESS DOES NOT EXCEED 6".
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer
service department. We will replace the part FREE of
charge.
Tel #: [phone]
E-Mail: [email protected]
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]
MAXIMUM WEIGHT CAPACITY: 165
LBS (75KGS) PER LEVEL.

MODEL #: DA1010BB-1 / DA1010BB-2
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING
NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
Request Date:
Name:
Shipping Address:
Street & Number:
City & State:
Zip Code:
Day Time Phone Number:
(including area code)
Date & Place of Purchase:
Part(s) description and quantity: (Please be sure to list model number or SKN number)
Customer Service Representative Mailing Address:
Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, QC, Canada, H1G 3L1
Customer Service
Customer Service Phone Number 1-800-295-1980
Email: da[email protected]
Customer Service Fax Number 514-353-7819

ESTE MANUEL DE INSTRUCCIONES
CONTIENE INFORMACIÓN DE
SEGURIDAD IMPORTANTE.
POR FAVOR LÉALO Y CONSÉRVELO
PARA REFERENCIA FUTURA.
_______ / _______ / _______
DA1010BB-2
DA1010BB-1
NOTA
Numero de lote:
(TOMADO DEL CARTON)
_____________________________________
Fecha de compra:
DOREL ASIA
Modelo No:
LITERA SIMPLE CODIGO UPC:
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]
NO DEVUELVA EL PRODUCTO A LA TIENDA.
Si falta una pieza o está dañada, contacte nuestro departamento de
servicio a la clientela. Reemplazaremos la pieza SIN cargo.
Tel #: [phone]
Correo electrónico: [email protected]
Fax #: [phone]
0-65857-17149-5
0-65857-17148-8

SERVICIO AL CLIENTE
*
*
*
*
*
*
*
*
*
*
*
*
UTILICE ÚNICAMENTE COLCHONES DE 74"-75" DE LARGO Y 37 1/2" - 38 1/2" DE ANCHO EN LA
DOS CUCHETAS. ASEGÚRESE DE QUE EL ESPESOR DEL COLCHÓN NO EXCEDA 6". LA
SUPERFICIE DEL COLCHÓN DEBE QUEDAR POR LO MENOS 5"(127MM) POR DEBAJO DEL
BORDE SUPERIOR DEL MARCO DE LAS CUCHETAS.
NO PERMITA QUE NIÑOS MENORES DE 6 AÑOS DUERMAN EN LA CUCHETA SUPERIOR.
PESO MÁXIMO: 165 LBS (75 KGS) POR NIVEL.
SIEMPRE UTILICE LAS BARANDAS EN LOS DOS LADOS DE LA CUCHETA SUPERIOR. SI LA
CUCHETA ESTÁ COLOCADA CERCA DE UNA PARED, LA BARANDA QUE CUBRE EL LADO
LARGO DE LA CUCHETA DEBE SER COLOCADA CONTRA LA PARED PARA EVITAR QUE EL
NIÑO QUEDE ATRAPADO ENTRE LA CAMA Y LA PARED (ESTO SE APLICA A LAS CUCHETAS
CON BARANDA LARGA DE UN SOLO LADO).
SIGA LA INFORMACIÓN DE LAS ADVERTENCIAS INSCRITAS EN LA ESTRUCTURA DE LA
CUCHETA SUPERIOR Y EN EL CARTÓN. NO RETIRE LA ETIQUETA DE ADVERTENCIAS DE LA
CAMA.
LA BASE DEL COLCHÓN ESTÁ DISEÑADA PARA SOPORTAR UN COLCHÓN SIN NECESIDAD DE
USAR UNA TABLA PARA MANTENER LA POSICIÓN O UN SOPORTE CON RESORTES.
SIEMPRE UTILICE EL TAMAÑO DE COLCHÓN O DE SOPORTE DE COLCHÓN RECOMENDADO, O
LOS DOS, PARA EVITAR LA POSIBILIDAD DE CAÍDAS O QUE EL NIÑO QUEDE ATRAPADO.
UTILICE SOLAMENTE COLCHONES CON RESORTES EN ESPIRAL EN LAS DOS CUCHETAS. EL
NO RESPETAR ESTO PUEDE CAUSAR LESIONES.
VERIFIQUE LA CAMA PERIÓDICAMENTE Y ASEGÚRESE DE QUE EL CUADRO, LA ESCALERILLA
Y OTROS COMPONENTES ESTÉN EN LA POSICIÓN CORRECTA, NO ESTÉN DAÑADOS Y TODAS
LAS UNIONES ESTÉN BIEN AJUSTADAS.
NO PERMITA QUE LOS NIÑOS HAGAN PAYASADAS SOBRE O DEBAJO DE LA CAMA Y PROHIBA
QUE SALTEN SOBRE ELLA.
NO UTILICE PIEZAS DE SUSTITUCIÓN. CONTACTE EL SERVICIO AL CLIENTE PARA OBTENER
PIEZAS PARA REMPLAZAR.
Montreal, Quebec
Canada, H1G 3L1
CORREO ELECTRÓNICO: [email protected]
ADVERTENCIAS
PELIGRO DE ESTRANGULAMIENTO - NUNCA CUELGUE O ATE EN LA CAMA ARTÍCULOS QUE
NO ESTÉN DISEÑADOS PARA USARLOS CON LA CAMA; POR EJEMPLO, PERO NO LIMITADO A
ESTO, GANCHOS, CINTURONES Y CUERDAS DE SALTAR.
Si faltan piezas o si tiene alguna pregunta sobre este producto, ¡comuníquese con nuestro representante de servicio!
LLAME AL 1-800-295-1980
También puede pedir piezas escribiendo a la siguiente dirección. Por favor incluya el
número de modelo, color y una descripción detallada de la pieza.
Departamento de Servicio al Cliente No. 413
12345 Albert-Hudon Boulevard, Suite 100