Dorel mother's choice flux User manual

motherschoice.com.au
follow us on
flux
3 wheel stroller
-
a
p
r
Illustrations and designs may vary.
IMPORTANT! KEEP FOR
FUTURE REFERENCE

2Mother’s Choice | Flux 3 Wheel Stroller
PREPARING SEAT AND VEHICLE
contents assembling the stroller
Components list
Opening stroller
Wheel assembly
Bumper bar assembly
using
Canopy
Swivel wheel
Operating brakes
Adjusting handle
Adjusting backrest
Drink bottle storage
Folding the stroller
Unfolding the stroller
Tether strap
Securing your child
Adjusting harness height
care and maintenance
Care instructions
Notes
Product registration
contacts
Customer service
4
5
6
7
8
10
11
12
13
14
15
16
17
18
19
20
21
23
24

3
Mother’s Choice | Flux 3 Wheel Stroller
These instructions detail the safe use, assembly and maintenance of your
product. Please read these instructions carefully and ensure that they are
followed at all times. Failure to do so could result in serious injury or death.
• ALWAYS APPLY THE BRAKES WHENEVER THE
STROLLER IS STATIONARY.
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• DO NOT LEAVE CHILDREN UNATTENDED.
• SECURE THE CHILD IN THE HARNESS AT ALL
TIMES AND ENSURE THAT THE SAFETY HARNESS
IS ADJUSTED FIRMLY BUT COMFORTABLY TO THE
CHILD’S BODY.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON
THIS STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY
MOVING PARTS IF YOU ADJUST THE STROLLER,
OTHERWISE THEY MAY BE INJURED.
• TO AVOID INJURY ENSURE THAT YOUR CHILD IS
KEPT AWAY WHEN FOLDING AND UNFOLDING THE
STROLLER.
• ENSURE THAT ALL LOCKING DEVICES ARE
ENGAGED BEFORE USE.
TO AVOID INJURY OR DEATH:
WARNING

4
Mother’s Choice | Flux 3 Wheel Stroller
• Never leave safety harness connected when not fitted
to a child in the stroller, as this may create loops that
cause a strangulation hazard.
• Never leave a child in the pram/stroller when
ascending or descending stairs
or escalators. Use great care when using the stroller
on other moving surfaces.
• Use the tether strap to prevent the stroller rolling away.
• Do not allow children to stand on the seat or footrest.
• Do not attempt to lift the stroller by the bumper bar.
• Engage front wheel swivel locks when travelling on
rough or uneven surfaces.
• Regularly inspect all parts and locking devices,
promptly replace worn out
or broken parts.
• Use only those accessories which are supplied by
Dorel Australia and approved for use with this stroller.
• To prevent the risk of the stroller catching fire, do not
park it near an open fire, heater or barbecue.
• Fingers or parts of the body could be injured when the
stroller is being folded or unfolded. Please use caution
when folding or unfolding the stroller.
WARNINGS

5
Mother’s Choice | Flux 3 Wheel Stroller
• This stroller has been designed for use on flat
or gently slopped surfaces. Using this stroller on
uneven or higher sloped surface may cause the
stroller to become unstable and tip over.
• Regularly inspect all parts and locking devices,
promptly replace worn out or broken parts.
• FIngers or parts of the body could be injured when
the stroller is being folded or unfolded. Please use
caution when folding or unfolding the stroller.
• This stroller has been designed for use on flat
or gently slopped surfaces. Using this stroller on
uneven or higher sloped surface may cause the
stroller to become untable and tip over.
• Do not run or jog with this stroller.
• Inflate tyre to 28psi/2.0Bar (195kPa). Over inflation
may result in tyre blow-out.
• The weight of the child using this stroller should not
be more than 20kg (approximately 4.5 years
of age).
• Shopping basket capacity should not be more
than 5kg.
• Maximum weight for the pocket should not be more
than 1kg.
WARNINGS

6Mother’s Choice | Flux 3 Wheel Stroller
COMPONENTS
1. Handle
2. Handle adjustment (both sides)
3. Folding lock (both sides)
4. Tether strap
5. Storage lock
6. Brake lever
7. Basket
8. Rear wheel
9. Front wheel assembly
10. Front wheel swivel lock
11. Footrest
12. Safety harness
13. Bumper bar
14. Canopy
15. Viewing window
1
2
5
14
13
12
11
9
10
4
3
6
8
7
15

7
Mother’s Choice | Flux 3 Wheel Stroller
ASSEMBLING
OPENING STROLLER
1. Release the storage latch (Figure 1a).
2. To unfold the stroller, simultaneously
lift handle and pull up with a swift motion
until and audible ‘click’ is heard. This will
ensure the locking mechanism has engaged. lift
click
unclip
1a

8Mother’s Choice | Flux 3 Wheel Stroller
ASSEMBLING
push
pull
REAR WHEEL ASSEMBLY
1. Align the round opening on the side of the
stroller with the wheel axle.
2. Push down on the metal pin located on the
bar of the frame (gure 2a). Simultaneously
slide the wheel onto the frame until it locks
into position.
REMOVE REAR WHEEL ASSEMBLY
1. Push down on the metal pin located on the
bar of the frame (gure 3a). Simultaneously
pull the wheel away from the frame to remove.
push
push
2a
3a
recommended front wheel
28psi
mother’s choice tip..
recommended front wheel
28psi
mother’s choice tip..

9
Mother’s Choice | Flux 3 Wheel Stroller
ASSEMBLING
ATTACHING BUMPER BAR
1. Align the bumper bar with the frame. Push
down onto the bumper bar until an audible
‘click’ conrms it is secure and in the correct
position.
REMOVING BUMPER BAR
1. To remove bumper bar, push in both buttons
located on the inner of the bumper bar
(gure 4a)and remove from frame.
push
click!
click!
align and push
4a

10 Mother’s Choice | Flux 3 Wheel Stroller
USING
USING CANOPY
1. Pull the front edge of the canopy to open
(gure 5a).
USING VIEWING WINDOW
1. To reveal viewing window, ensure canopy is
rst fully extended.
2. Lift ap from hook and loop tape and fold
back to reveal breathable mesh.
5a
mother’s choice tip...
The canopy is permanently attached to the stroller.

USING
11
Mother’s Choice | Flux 3 Wheel Stroller
6a 6b
6c 6d
CANOPY POSITIONS

12 Mother’s Choice | Flux 3 Wheel Stroller
USING
OPERATING FRONT SWIVEL WHEEL
TO LOCK:
Push the lever up to lock.
TO UNLOCK:
Push the lever down to engage swivel wheel.
locked swivel

13
Mother’s Choice | Flux 3 Wheel Stroller
USING
OPERATING BRAKES
1. To apply the brake, press down
rmly on the red brake pedal.
press down to apply
lift up to release

14 Mother’s Choice | Flux 3 Wheel Stroller
USING
3 positions
ADJUSTING HANDLE
1. There are two buttons either side of the handle bar.
2. Press both adjustment buttons simultaneously and rotate to
the desired position.
3. Listen for ‘click’.
swivel
press
press

15
Mother’s Choice | Flux 3 Wheel Stroller
USING
TO ADJUST BACKREST
1. To lower the backrest, squeeze the clasp to release and pull in
a downward motion. Release the clasp once desired position
has been reached.
2. To raise the backrest, squeeze the clasp and push whilst
sliding upwards to desired position.

16 Mother’s Choice | Flux 3 Wheel Stroller
USING
Mother’s Choice | Flux 3 Wheel Stroller
STORAGE POCKETS
1. Total weight must not exceed 1 kg in both pockets.

17
Mother’s Choice | Flux 3 Wheel Stroller
USING
FOLDING THE STROLLER
1. Apply rear wheel brakes.
2. Remove all items in the shopping basket.
3. Fold the canopy.
4. Unlock the front swivel wheel.
5. Adjust the backrest to full layback position
(see page 15).
6. Pull the folding locks up (gure 7a) and
simultaneously push down on the stroller
(gure 7b) to fold.
7. Ensure the locking latch is engaged (gure 7c)
to ensure the stroller is securely locked.
7a
pull
7b
7c
mother’s choice tip...
Lift handle to check that lock has fully engaged.

18 Mother’s Choice | Flux 3 Wheel Stroller
USING
UNFOLDING THE STROLLER
1. Prior to unfolding, ensure the storage latch is
released (gure 8a).
2. Simultaneously lift handle up in a short sharp
motion until you hear the locking mechanism
engage (gure 8b).
8a release latch
lift
8b
8c
click

19
Mother’s Choice | Flux 3 Wheel Stroller
USING
TETHER STRAP
Whenever a child is in the stroller
and brakes are NOT engaged, the
large loop should be around your
wrist (gure 9).
Correct use of the tether strap will prevent stroller runaway and
possible injury to your child.
WARNING
9

20 Mother’s Choice | Flux 3 Wheel Stroller
USING
SECURING YOUR CHILD
DG E
B
FC
A A
A1
5 points of the harness can be adjusted by moving each straps’ slider (gure A1).
To tighten or loosen the waist and/or shoulder straps, hold and lift the plastic
adjuster. Adjust straps to desired position.
The waist strap needs to t rmly around
the child.
1. Slip one shoulder strap (A) over each
shoulder and position crotch strap
between legs (gure 10a)
2. Place buckle prong (D) on top of
buckle prong (gure 10b)
3. Insert the prongs into the buckle
housing (E) until it clicks into position.
Repeat the above steps for the
opposite side (F and G). Pull straps to
ensure they are locked into the buckle
assembly.(gure 10c)
C
D
E
DG
FC
SQUEEZE
4. The harness should resemble
this image. (gure 10d)
5. The buckle is released by squeezing
the top and bottom prongs together
until harness disengages. (10e).
10b 10c
10d 10e
10a