Dormakaba SLI-A Interlock User manual

WN 059734 45532 – 2018-11
DE
SLI-A Interlock
Installation manual
Contents
1 About this document 1
2 Safety 1
3 Product description 1
4 Loading the application 3
5 Configuration of system doors 4
6 Parameterization of system doors with TMS
Soft® 4
7 Configuration of an interlock with TMS Soft® 4
8 LED display on the illuminated ring 5
9 Disassembly and disposal 5
1 About this document
1.1 Contents and purpose
This document describes the installation of the SLI-A
Interlock application.
1.2 Target group
This document is intended for assembling technicians
and specialists authorized for installation by
dormakaba.
1.3 Other applicable documents
• The SCU control units’ mounting instructions
• The SafeRoute® system manual
• The respective door units’ inspection log
• The TMS Soft® handbook
1.4 Documents storage
This document must be handed over to the facility
operator after commissioning.
1.5 Symbols used
1.5.1 Hazard categories
WARNING
This signal world indicates a possible
hazardous situation which may result in
death or severe injuries if ignored.
ATTENTION
This signal word indicates a situation of
potential risk, which could lead to damage
to property or the environment if not
averted.
1.5.2 More symbols
TIPS AND RECOMMENDATIONS
This signal word indicates useful information
for efficient and trouble-free operation.
2 Safety
2.1 Intended use
The functional scope of a SafeRoute® system is
extended by loading the application into the control
unit.
2.2 Personnel qualification
Installation may only be carried out by persons
authorized by dormakaba.
3 Product description
With the SLI-A interlock application, a SafeRoute®
Control Unit can operate up to 4 independent doors
with different configurations in 1 interlock. The system
cabling takes place via DCW® bus. The SLI-A Interlock
includes all functions of the SLI-A Multi-door.
The loaded applications are permanently stored on
the SLI license card. After replacement of the SLI
license card, any necessary applications must be
reloaded.

2SLI-A Interlock 2018-11
WN 059734 45532
dormakaba Installation manual Product description
3.1 Interlock types
Different types of interlocks can be implemented. The
doors are assigned to the interlocks in TMS Soft®.
3.1.1 Interlock type 1
Interlock 1
1 2 3 4
Doors 1 to 4 are assigned to interlock 1.
Interlock function: A door inside interlock 1 can only be
opened when all other doors are locked.
3.1.2 Interlock type 2
Interlock 1
1 2 3
Doors 1 to 2 are assigned to interlock 1. Interlock
function: Door 3 is not assigned to an interlock. A
door inside interlock 1 can only be opened when the
opposite side is locked. Door 3 can always be opened
independently of interlock 1.
3.1.3 Interlock type 3
Interlock 1 Interlock 2
1 32 4
Doors 1 and 2 are assigned to interlock 1 and doors 3
and 4 are assigned to interlock 2.
Interlock function: A door inside interlock 1 or 2 can
only be opened when the opposite side is locked. The
interlocks work independently of each other.
3.1.4 Interlock type 4
Interlock 1 Interlock 2
1 2 3 4
Doors 1 and 3 are assigned to interlock 1 and doors 3
and 4 are assigned to interlock 2.
Interlock function: Door 3 is assigned to both
interlocks and can only be opened when doors 1, 2 and
4 are locked.
3.1.5 Interlock type 5
Interlock 1 Interlock 3Interlock 2
1 2 3 4
Doors 1 and 2 are assigned to interlock 1, doors 2 and
3 are assigned to interlock 2 and doors 3 and 4 are
assigned to interlock 3.
Interlock function: Door 2 is assigned to 2 interlocks
and can only be opened when doors 1 and 3 are
locked. Door 3 is also assigned to 2 interlocks and can
only be opened when the doors 2 and 4 are locked.
3.1.6 Interlock type 6
Interlock 3
Interlock 1 Interlock 2
1
4 3
2
Doors 1 and 4 are assigned to interlock 1, doors 1 and 3
are assigned to interlock 2 and doors 1 and 2 are
assigned to interlock 3.
Interlock function: Door 1 is assigned to 3 interlocks
and can only be opened when doors 2, 3 and 4 are
locked. Doors 2, 3 and 4 can only be opened when door
1 is locked.
3.2 Parts included
SLI-A Interlock 56412101

3SLI-A Interlock 2018-11WN 059734 45532
dormakaba Installation manual Loading the application
4 Loading the application
4.1 Prerequisite for loading the application
• A SafeRoute® system with license level Basic or
higher.
• The DCW® addressing of the DCW® components
emergency button and STV xxx must be assigned
to the associated system doors. The settings are
made via the DIP switches on the components (see
corresponding assembly instructions).
4.1.1 DCW® addressing of DCW®
components
WARNING
An STV xxx lock may only be configured with
emergency buttons assigned to the same
system door!
TIPS AND RECOMMENDATIONS
If it is unclear whether an SCU emergency
button has ever been operated as a control
unit with a license card:
Press the service button S4 for 8 s with
the power supply switched on. The LED
indicator changes to rainbow display.
TIPS AND RECOMMENDATIONS
The SafeRoute® Control Unit SCU is
automatically assigned to the system door
no. 1.
DIP switch settings
Switch designation in ()
ON
1
0
SafeRoute® Control
Unit SCU:
- SCU-UP/-TL (S6)
- SCU-DR (mode1/2)
Emergency button SCU without
license card (S6), STV xxx, DCW®
Standard modules
Number
of
doors
DIP
switch
System
door
DCW®
address
DIP
switch
1 0 0 No. 1
1 or
2 or
3 or
4
0
1
0
1
0
0
1
1
2 1 0
No. 1 1 or
4
0
1
0
1
No. 2 2 or
3
1
0
0
1
3 0 1
No. 1 1 or
4
0
1
0
1
No. 2 2 1 0
No. 3 3 0 1
4 1 1
No. 1 1 0 0
No. 2 2 1 0
No. 3 3 0 1
No. 4 4 1 1
4.1.2 Assignment of the LED segments on
the illuminated ring
The status display is indicated by the illuminated
ring. The LED segments are assigned to the DCW®
security components (STV xxx and SCU xx) and light
up or flash depending on the status of the connected
DCW® component. If DCW® addresses are duplicated,
an error message will appear. The duplicate DCW®
address flashes yellow.
STV 1 (Addr. 1)SCU 1 (Addr. 1)
STV 2
(Addr. 2)
SCU 2
(Addr. 2)
STV 3
(Addr. 3)
SCU 3
(Addr. 3)
STV 4
(Addr. 4)
SCU 4
(Addr. 4)
Fig. 1 Assignment of the LED segments in the illuminated
ring
4.2 Load the applications to a SafeRoute®
Control Unit
The applications are loaded by inserting them into
the slot for the license card in the control unit of
a SafeRoute® system according to the respective
assembly instructions. The SCU’s power supply must
not be disconnected.
ATTENTION
Risk of property damage from electrostatic
discharge.
The control board may be damaged
by an electrostatic discharge!
• Ground your own body before
touching a component!
TIPS AND RECOMMENDATIONS
The license card must be reinserted within 2
minutes.

4SLI-A Interlock 2018-11
WN 059734 45532
dormakaba Installation manual Configuration of system doors
1. Remove the existing SLI license card and insert
the SLI-A application card.
‣ The SLI LED starts flashing when the
application has been loaded from the card to
the control unit.
→The SLI card is empty.
2. Remove the application card and insert the license
card again.
‣ The LED SLI lights up when the application
has been saved on the license card.
→The license card now contains the license and
the 2 additional functions.
3. Dispose of the SLI application card in an
environmentally friendly manner.
4. Document the use of the applications in each
system door’s inspection log.
5 Configuration of system doors
5.1 Configure the system doors
1. Press and hold the S4 service button on the SCU
with the license card for 12s.
‣ The LED indicator lights up solid blue for 4
seconds on all emergency buttons.
‣ The LED configuration and DCW® LED on the
STV xxx board flash slowly (2.5 Hz).
‣ The connected components are detected
and displayed on the relevant system door’s
illuminated ring (lights up blue).
2. Check if the connected components are displayed
with the correct address.
Display example for illuminated ring display in a
multi-door system with 4 doors:
System door 1:
SCU 1 STV 1 SCU 1 STV 1
or
(Display for use with (Display for use with
SCU-UP and SCU-TL) SCU-DR)
System door 2:
SCU 2 STV 2
System door 3:
SCU 3 STV 3
System door 4:
SCU 4 STV 4
3. Press and hold the S4 service button on the SCU
with the license card for 3s.
‣ The LED display turns permanently green
on all emergency buttons. The locks are not
activated yet.
4. Briefly push the key on each system door to the
left.
‣ The LED display changes to red.
→The locks are activated.
5. Check and document the unit’s correct function
(see also operation manual).
6 Parameterization of system
doors with TMS Soft®
The functions of the components and the SafeRoute®
system can be adapted with TMS Soft®. For more
information, see the TMS Soft® handbook and the
help function in TMSSoft®.
6.1 Requirements for parameterization
• The control unit must be connected to the TMS
Soft® computer via LON/LAN or directly via the
RS232 interface.
• The system doors must be inserted in TMSSoft®.
• The multi-door application must be activated (see
TMS Soft® > Communication, here: Applications
column).

5SLI-A Interlock 2018-11WN 059734 45532
dormakaba Installation manual Configuration of an interlock with TMS Soft®
7 Configuration of an interlock
with TMS Soft®
The functions of the components and the SafeRoute®
system can be adapted with TMS Soft®. For more
information, see the TMS Soft® handbook and the
help function in TMSSoft®.
7.1 Requirements for parameterization
• The control unit must be connected to the TMS
Soft® computer via LON/LAN or directly via the
RS232 interface.
• The system doors must be inserted in TMSSoft®.
• The Multi-door and Interlock applications must be
activated (see TMS Soft® > Communication, here:
Applications column).
8 LED display on the illuminated
ring
LED segments 1 and 8 flash when attempting to open
a system door while the interlock is blocked.
9 Disassembly and disposal
Disassembly is carried out in the reverse order of
mounting and must be carried out by qualified
personnel.
The product must be disposed of in an
environmentally friendly manner. Electro-
technical parts and batteries must not be
disposed of as domestic waste. Dispose of
electrotechnical parts and batteries in the designated
acceptance and collection points. Refer to the
statutory regulations for your country.

6SLI-A Interlock 2018-11
WN 059734 45532
dormakaba Installation manual Configuration of system doors

7SLI-A Interlock 2018-11WN 059734 45532
dormakaba Installation manual Configuration of system doors

dormakaba Deutschland GmbH
DORMA Platz 1 58256 Ennepetal Germany T: [phone] F: [phone] www.dormakaba.com
Translation of the original document, subject to change without notice