Draytek Vigor 2800 User manual

i
Vigor2800 Series Quick Start Guide
Copyright Information
Copyright
Declarations
Copyright 2005 All rights reserved. This publication contains
information that is protected by copyright. No part may be
reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
• Microsoft is a registered trademark of Microsoft Corp.
• Windows, Windows 95, 98, Me, NT, 2000, XP and Explorer
are trademarks of Microsoft Corp.
• Apple and Mac OS are registered trademarks of Apple
Computer Inc.
Other products may be trademarks or registered trademarks
of their respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
• Read the installation guide thoroughly before you set up
the router.
•The router is a complicated electronic unit that may be
repaired only be authorized and qualified personnel. Do
not try to open or repair the router yourself.
•Do not place the router in a damp or humid place, e.g. a
bathroom.
•Do not stack the routers.
•The router should be used in a sheltered area, within a
temperature range of +5 to +40 Celsius.
•Do not expose the router to direct sunlight or other heat
sources. The housing and electronic components may be
damaged by direct sunlight or heat sources.
•Keep the package out of reach of children.
•When you want to dispose of the router, please follow local
regulations on conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the
router will be free from any defects in workmanship or
materials for a period of three (3) years from the date of
purchase from the dealer. Please keep your purchase
receipt in a safe place as it serves as proof of date of
purchase. During the warranty period, and upon proof of
purchase, should the product have indications of failure due
to faulty workmanship and/or materials, we will, at our
discretion, repair or replace the defective products or

ii
components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product
to proper operating condition. Any replacement will consist
of a new or re-manufactured functionally equivalent product
of equal value, and will be offered solely at our discretion.
This warranty will not apply if the product is modified,
misused, tampered with, damaged by an act of God, or
subjected to abnormal working conditions. The warranty
does not cover the bundled or licensed software of other
vendors. Defects which do not significantly affect the
usability of the product will not be covered by the warranty.
We reserve the right to revise the manual and online
documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of
such revision or changes.
Be a
Registered
Owner
Web registration is preferred. You can register your Vigor
router via http://www.draytek.com. Alternatively, fill in the
registration card and mail it to the address found on the
reverse side of the card.
Firmware &
Tools Updates Due to the continuous evolution of DrayTek ADSL & Router
technology, all routers will be regularly upgraded. Please
consult the DrayTek web site for more information on newest
firmware, tools and documents.
http://www.draytek.com

iii
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park,
Hsin-Chu, Taiwan 303
Product: Vigor2800 Series ADSL2/2+ Routers
DrayTek Corp. declares that Vigor2800 series of routers are in compliance with
the following essential requirements and other relevant provisions of R&TTE
Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility
(EMC) Directive 89/336/EEC by complying with the requirements set forth in
EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive
73/23/EEC by complying with the requirements set forth in EN60950.
The Vigor2800G/Gi are designed for the WLAN 2.4GHz network throughput EC
region, Switzerland, and the restrictions of France.

iv
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the use is
encouraged to try to correct the interference by one of the following measures:
♦Reorient or relocate the receiving antenna.
♦Increase the separation between the equipment and receiver.
♦Connect the equipment into an outlet on a circuit different form that to
which the receiver is connected.
♦Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device many not cause harmful interference, and
(2) This device may accept any interference received, including interference that
may cause undesired operation.

v
Table of Contents
1. Introduction……………………………………….………………….……………. 1
1.1
Brief Overview…………………………………………………………..……… 2
1.2
Specifications………………………………………………………..…………. 3
1.3
Front Panel LEDs and Rear Panel Interfaces………………..……….…… 5
1.4
Package Contains……………………………………….…………..…………. 9
2. Quick Install Your Vigor2800 Series Router…………………..…….. 10
2.1
Hardware Installation……………………………….……………..………….. 10
2.2
Configure Your Router via Quick Start Wizard…….……………..………. 11
3. Wireless LAN Settings (for G models)………….………….……….…… 14
3.1
General Settings…………………………………….…………………..……... 15
3.2
Security Settings…………………………………………….……………...…. 16
3.3
WDS Settings…………………………………………….……………...……… 17
4. Trouble Shooting………………………………………………………..………. 19
Is the Hardware Status OK?……………………………………………………. 19
Are the Network Connection Settings on Your PC OK?…………………….. 19
Can You Ping the Router from PC?………………………………..……….… 21
Are the ISP Settings OK?…………………………………………………...…. 22
Back to Factory Default Setting………………………………………………… 23

1
1. Introduction
Highlights
zEasy Internet-sharing of your broadband connection
zRobust firewall to help protect your network from external attacks
For G models:
zWireless LAN with data rate up to 108Mbps using Super G®
technology
zSecure connection with advanced WPA2 encryption and
authentication
Model comparison chart:
ADSL2/2+ Router High Speed
Wireless AP ISDN
Vigor2800Gi * * *
Vigor2800G * * -
Vigor2800i * - *
Vigor2800 * - -

2
1.1 Brief Overview
Targeting requirement for residential, SOHO (Small Office and Home Office)
and business users, the Vigor2800 series are ADSL2/2+ enabled integrated
access device. With downstream speed up to 12Mbps (ADSL2) or 24Mbps
(ADSL2+), the Vigor2800 series provide exceptional bandwidth* for Internet
access. (*note: the available bandwidth also depends on the Internet Service Provider)
Embedded with sophistic VPN firewall security features, the Vigor2800 series
provide 32 dedicated virtual private data networks tunneling through public
Internet. Powered by hardware-based DES/3DES engine, all the information
transmitted is well encrypted. Hence Vigor2800 series can against any
snooping without performance degraded when VPN is enabled.
The Vigor2800 G models are embedded 802.11g compliant wireless module
which provides wireless LAN access with line rate as much as 54Mbps. The
Vigor2800 G models feature WPA2 (802.11i), wireless LAN isolation, WDS
(Wireless Distribution System), and Universal VLAN™. The Vigor2800 i
models provide ISDN backup, which keep your internet access alive even
when ADSL internet access fails.

3
1.2 Specifications
For Vigor2800 G models
Wireless Access Point
IEEE802.11b/g compliant
¾64/128-bit WEP
¾WPA/WPA2(IEEE802.11i)
¾802.1x authentication with
RADIUS client
VPN over WLAN
Wireless client list
Hidden SSID
MAC address access control
Access point discovery
Wireless VLAN*
Wireless LAN isolation
Wireless client isolation
Wireless rate-control*
WDS (Wireless Distribution
System)
Super G TM
¾Up to 108 Mbps data rate **
¾Utilizing adaptive radio to
automatically identify clear
channels
¾Real-time hardware data
compression
¾Fast Frames TM and
standards-compliant bursting
* *Actual data throughput will vary
according to the network conditions and
environmental factors, including volume of
network traffic, network overhead and
building materials.
For Vigor2800 i models All models
ISDN
Euro ISDN compatible
Automatic ISDN backup
Support
64/128Kbps(multilink-PPP)/BOD
(Bandwidth on Demand)
Remote Dial-In/LAN-to-LAN
connection
Remote activation
Virtual TA
ADSL Compliant
ADSL
¾G.dmt (G.992.1)
¾G.lite (G.992.2)
¾ANSI T1.413 issue2
ADSL2
¾G.dmt.bis(G.992.3)
¾G.lite.bis(G.992.4)
ADSL2+(G.992.5)
Up to 24Mbps downstream and
1Mbps upstream
ATM Protocols
Multiple Protocol over AAL5 (RFC
2684)
PPP over Ethernet and AAL5
(RFC 2516,2364)
Up to 8 PVC
PPPoE pass through LAN/WLAN
Transparent bridge for MPoA

4
VPN
Up to 32 VPN tunnels
Supported protocol: PPTP,
IPSec, L2TP, L2TP over IPSec
DHCP over IPSec(*)
Encryption: AES, MPPE and
hardware-based DES/3DES
Authentication: MD5, SHA-1
IKE authentication: pre-shared
key and digital signature(X.509)*
LAN-to-LAN, Teleworker-to-LAN
Firewall Facilities
IM/P2P blocking
Multi-NAT, DMZ host,
port-redirect/open port
Rule-based packet filtering
Stateful packet inspection
DoS/DDoS protection
IP address anti-spoofing
E-mail alert and logging via
syslog
VPN pass through
QoS
Class-based bandwidth
guarantee by user-defined traffic
categories
Support 4 priority levels
Support of DiffServ Code Point
classifying
Printer Server
One USB port connector
Built-in LPR printer server
Provide LPR printer for Windows
98/SE/ME
Compatible with Windows
2000/XP/Server 2003/MAC OS
9/MAC OS X built-in LPR printer
driver
Network Features
DHCP client/relay/server
Dynamic DNS
SNTP client
Call scheduling
RADIUS client
DNS cache/proxy
UPnP
Routing protocol:
¾Static routing
¾RIP V2
Router Management
Web-based user interface
(HTTP/HTTPS)
Quick Start Wizard
CLI (Command Line Interface,
Telnet/SSH*)
Administration access control
Configuration backup/restore
Built-in diagnostic function
Firmware upgrade via TFTP/FTP
Syslog
SNMP management MIB-II
Content Filtering
URL blocking
Java Applet, Cookies, Active X,
compressed, executable,
multimedia
Time schedule control
Power Consumption
15Watt Max.
*future release

5
1.3 Front Panel LEDs and Rear Panel Interfaces
1.3.1 Vigor2800Gi
LED Status Explanation
ACT (Activity) blinking The router is powered on and running properly.
on The ISDN network is correctly setup.
ISDN blinking A successful remote connection on the ISDN BRI B1/B2
channel.
on The P2P function is active
P2P blinking When starting to prohibit P2P data
on The DoS function is enabled.
Firewall blinking When encountered DoS attacks.
on The wireless LAN function is enabled.
WLAN blinking Ethernet packets are transmitting over wireless LAN.
DSL on The ADSL,ADSL2/2+ line is showtime.
Printer on The USB interface printer is ready.
orange A normal 10Mbps connection is through its corresponding
port.
green A normal 100Mbps connection is through its corresponding
port.
LAN
(P1, P2, P3,
P4)
blinking Ethernet packets are transmitting.
Interface Description
Printer Connect to the USB printer.
PWR Connect the included power adapter to the power outlet.
P1, P2, P3, P4 Connect to the local networked devices.
DSL Connect the ADSL,ADSL2/2+ line to access the Internet.
ISDN Connect to the NT1 (or NT1+) box provided by ISDN service provider.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and
keep for more than 5 seconds. When the ACT LED begins to blink
rapidly, release the button. Then the router will restart with the factory
default configuration.

6
1.3.2 Vigor2800G
LED Status Explanation
ACT (Activity) blinking The router is powered on and running properly.
QoS on The QoS function is active.
on The P2P function is active
P2P blinking When starting to prohibit P2P data
on The DoS function is enabled.
Firewall blinking When encountered DoS attacks.
on The Wireless LAN function is enabled.
WLAN blinking Ethernet packets are transmitting over wireless LAN.
DSL on The ADSL,ADSL2/2+ line is showtime.
Printer on The USB interface printer is ready.
orange A normal 10Mbps connection is through its corresponding
port.
green A normal 100Mbps connection is through its corresponding
port.
LAN
(P1, P2, P3,
P4)
blinking Ethernet packets are transmitting.
Interface Description
Printer Connect to the USB printer.
PWR Connect the included power adapter to the power outlet.
P1, P2, P3, P4 Connect to the local networked devices.
DSL Connect the ADSL,ADSL2/2+ line to access the Internet.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and
keep for more than 5 seconds. When the ACT LED begins to blink
rapidly, release the button. Then the router will restart with the factory
default configuration.

7
1.3.3 Vigor2800i
LED Status Explanation
ACT (Activity) blinking The router is powered on and running properly.
on The ISDN network is correctly setup.
ISDN blinking A successful remote connection on the ISDN BRI B1/B2
channel.
on The P2P function is active
P2P blinking When starting to prohibit P2P data
on The DoS function is enabled.
Firewall blinking When encountered DoS attacks.
VPN on The VPN tunnel is launched.
DSL on The ADSL,ADSL2/2+ line is showtime.
Printer on The USB interface printer is ready.
orange A normal 10Mbps connection is through its corresponding
port.
green A normal 100Mbps connection is through its corresponding
port.
LAN
(P1, P2, P3,
P4)
blinking Ethernet packets are transmitting.
Interface Description
Printer Connect to the USB printer.
PWR Connect the included power adapter to the power outlet.
P1, P2, P3, P4 Connect to the local networked devices.
DSL Connect the ADSL,ADSL2/2+ line to access the Internet.
ISDN Connect to the NT1 (or NT1+) box provided by ISDN service provider.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and
keep for more than 5 seconds. When the ACT LED begins to blink
rapidly, release the button. Then the router will restart with the factory
default configuration.

8
1.3.4 Vigor2800
LED Status Explanation
ACT (Activity) blinking The router is powered on and running properly.
QoS on The QoS function is active.
on The P2P function is active
P2P blinking When starting to prohibit P2P data
on The DoS function is enabled.
Firewall blinking When encountered DoS attacks.
VPN on The VPN function is active.
DSL on The ADSL,ADSL2/2+ line is showtime.
Printer on The USB interface printer is ready.
orange A normal 10Mbps connection is through its corresponding
port.
green A normal 100Mbps connection is through its corresponding
port.
LAN
(P1, P2, P3,
P4)
blinking Ethernet packets are transmitting.
Interface Description
Printer Connect to the USB printer.
PWR Connect the included power adapter to the power outlet.
P1, P2, P3, P4 Connect to the local networked devices.
DSL Connect the ADSL,ADSL2/2+ line to access the Internet.
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and
keep for more than 5 seconds. When the ACT LED begins to blink
rapidly, release the button. Then the router will restart with the factory
default configuration.

9
1.4 Package Contains
Quick Start Guide CD
UK-type power adapter EU-type power adapter
USA/Taiwan-type power
adapter AU/NZ-type power adapter
RJ-45 Cable (Ethernet) RJ-45 to RJ-45 (ISDN) for
Vigor2800 i models
or
RJ-11 to RJ-45 (Annex B) RJ-11 Cable (Annex A / B)
RJ-11 Cable (PSTN line)
Antennas for V2800 G models

10
2. Quick Install Your Vigor2800 Series Router
2.1 Hardware Installation
Before starting to configure the router, you have to connect your devices
correctly.
1. Connect the DSL interface to the external ADSL splitter with an ADSL line
cable.
2. Connect one port of 4-port switch to your computer with a RJ-45 cable.
3. For G models, connect detachable antennas to the router.
4. Connect the attached power adapter to the power port.
5. Check the ACT and WAN, LAN LEDs to assure network connections.
(Regarding the detailed LED status explanation, please refer to section 1.3)

11
2.2 Configure Your Router via Quick Start Wizard
Introduction
The Quick Start Wizard is designed for you to easily set up your broadband
Internet access. You can directly access the Quick Start Wizard via Web
Configurator.
Configure Your Router via Quick Start Wizard
First make sure your PC connects to router correctly. You may either
simply set up your PC to dynamic get IP from router or set up the IP
address of PC to be the same subnet as the default IP address of
Vigor router 192.168.1.1. If you don’t know how, please refer to Trouble
Shooting.
Then open the web browser on the PC. Type http://192.168.1.1. If your
link is successful, a pop-up window will open to ask for username and
password. Leave the default null value and press OK to continue.
Step 1.
If you fail to access to the web configuration, please refer to “Trouble
Shooting” guide.
Step 2. The Main Menu will pop out after completing previous step.

12
Step 3. Now Quick Start Wizard is switched on. Enter login password. Then
click Next to continue.
Step 4 Select the appropriate Internet access type according to the information
from your ISP. Or Clicking “Auto detect” button also offers the related
DSL parameters automatically.
Step 5 If PPPoE/PPPoA is selected, please manually enter the
Username/Password provided by your ISP service provider. Checking
the Always On means Internet access is always on regardless of
Internet usage.

13
Step 6 Review the summary of settings.
On the bottom of Web Configurator window, you can find messages showing the
system interaction with you.
z“Ready” indicates the system is ready for you to input settings.
z“Settings Saved” means your settings are saved once you click “Finish” or
“OK” button.

14
3. Wireless LAN Settings(for G models)
Select from the menu of the Wireless LAN:
Wireless LAN >> General Settings
Security
Access Control
WDS Settings
Access Point Discovery
Station List
(The default value of Frequency Domain was set by factory depends on the
reselling region.)
Wireless Distribution System
Wireless Distribution System(WDS) is an advanced technology to link 2 LANs or
2 WLANs through air, if router is set in Bridge Mode, or to extend a Wireless
LAN coverage area, if router is set in Repeater Mode
Example Application 1
Example Application 2