Draytek Vigor2600Ge Reference manual

1
Vigor2600Ge introduction
The Vigor2600Ge WLAN ADSL router is an Internet access solution for your LAN which not only provides you
with shared web surfing but also countless other value-added features such as Firewall / Security, VPN, multimedia
support, and 54Mbps 802.11g Wireless LAN and all in a reliable one-box solution.
Annex A / Annex B
ISDN Backup
Wireless AP
ADSL Router *
* / *
Vigor2600Ge
*
_
Brief Overview

2
LED Indicators Descriptions
Descriptions
Back Panels
ACT (Activity) Blink when power is supplied to the router and the router is running normally.
P1, P2,
P3, P4
PWR Only the power adapter comes with the package can be connected to the PWR.
These switch ports should be connected to your local PCs.
P1, P2, P3, P4
The restore default settings : While the router is running (ACT LED blinking),
press the button and hold for more than five seconds. The ACT LED begins to
blink rapidly, then release the button. The router will restart with the factory
default configuration.
Factory Reset
LAN
These indicators are dual-colour LEDs:
- OFF indicates that no device is connected to the LAN port.
- Yellow indicates that the port is connecting to a 10Mbps device.
- Green indicates that the port is connecting to a 100Mbps.
- BLINKING indicates that Ethernet packets are passing through the port.
ADSL To connect to the ADSL-enabled telephone line.
ON when the wireless LAN is ready.
ADSL LINE
DATA
ON when the ADSL network is showtime.
Blinking indicates the DSL protocols start hankshaking.
The light will remain still when data transmission is available.
WLAN
LED Indicators and
Back Panels
Before you begin to install, please take a moment to become more familiar with the LED
indicators and rear panels. The following section describes the model.
Vigor2600Ge
There are three LEDs below the bandwidth utilization bar. From left to right,
they indicate bandwidth utilization, from low to high.

3
Copyright
Declarations
Copyright 2004All rights reserved. This publication contains information that is
protected by copyright.No part may be reproduced, transmitted, transcribed, stored
in a retrieval system, or translated into any language without written permission from
the copyright holders.
The following trademarks are used in this document:
. Microsoft is a registered trademark of Microsoft Corp.
. Windows,Windows 95, 98, Me, NT, 2000, XP and Explorer are trademarks of
Microsoft Corp.
. Apple and Mac OS are registered trademarks of Apple Computer Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Trademarks
Safety Instructions
Warranty
. Read the installation guide thoroughly before you set up the router.
. The router is a complicated electronic unit that may be repaired only be authorized
and qualified personnel.Do not try to open or repair the router yourself.
. Do not place the router in a damp or humid place, e.g. a bathroom.
. The router should be used in a sheltered area, within a temperature range of +5 to +40
Celsius.
. Do not expose the router to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
. Keep the package out of reach of children.
. When you want to dispose of the router, please follow local regulations on
conservation of the environment.
We warrant to the original end user (purchaser) that the router wil be free from any
defects in workmanship or materials for a period of three (3) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it
serves as proof of date of purchase.During the warranty period, and upon proof of
purchase, should the product have indications of failure due to faulty workmanship
and/or materials, we will, at our discretion, repair or replace the defective products
or components, without charge for either parts or labor, to whatever extent we
deem necessary tore-store the product to proper operating condition. Any
replacement will consist of a new or re-manufactured functionally equivalent product
of equal value, and will be offered solely at our discretion. This warranty will not
apply if the product is modified, misused, tampered with, damaged by an act of God,
or subjected to abnormal working conditions. The warranty does not cover the
bundled or licensed software of other vendors. Defects which do not significantly
©

4
affect the usability of the product will not be covered by the warranty.We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any person of
such revision or changes.
European Community
Be A Registered
Owner
Firmware & Tools
Updates
Hereby, we declare that the router is in compliance with the essential requirements
and other relevant provisions of R&TTE Directive 99/5/EC. The Vigor 2600Ge is
designed for theWLAN 2.4Ghz network throughout EC region, Switzerland, and
the restrictions of France.
Web registration is preferred. You can register your Vigor router via http://
www.draytek.com.tw . Alternatively, fill in the registration card and mail it to the
address found on the reverse side of the card.
Due to the continuous evolution ofDrayTek ADSL & Router technology, all
routers will be regularly upgraded. Please consult the DrayTek web site for more
information on newest firmware, tools and documents.
http://www.draytek.com.tw

5
Vigor2600Ge Quick Start Guide
Identify your variant
Delivery check
Aim of this
chapter
Quickly connect your router to the Internet
Check your router package for the following items :
The Router
1 printed Quick StartGuide with warranty/ registration card
1 CDincludes detailed User Manual in electronic form, released firmware and
utilities
1AC power supply adapter (black)
1 Ethernet LAN cable (blue) for connection to a computer or hub
1ADSL line cable (RJ-11 to RJ-45 for Switzerland and theNetherlands only)
(RJ-11 to RJ-11 for other Annex A countries)
(RJ-45 to RJ-45 for Annex B countries)
1Detachable antenna
Please read page 6,7
Your router package should contain all these items. If any item is
missing or damaged, contact your dealer or our Customer Service
Department immediately.
The Vigor2600Ge contain Annex A/Annex B models,
please check if the package is suitble for your use by checking the
information from bottom of Vigor2600Ge router.
AnnexA: is for connecting to an analog POTS line
Annex B : is for connecting to a digital ISDN line

6
UK-type power adapter
CD
EU-type power adapter
AU/NZ-type power adapter
USA/Taiwan-type power
adapter
Manual
Package Contains

7
RJ-11 to RJ-11(Annex A)
RJ-11 to RJ-45(Annex B)
Dutch/Swiss User
RJ-45(Enternet)
RJ-45 to RJ-45
(Annex B)
Filter/Splitter(Optional) Antenna

8
Internet Cofiguration
Requirements
DSL Parameters
The following DSL parameters are required from your ISP :
1. The VPI/VCI of the virtual channel to use on the DSL line
2. Protocol : PPPoE, PPPoA or MPoA (RFC1483/2684)
3. Encapsulation Method : LLC/SNAP or VCMUX
4. Modulation Method : T1.413,G.lite, G.dmt
DSL line
Depending on the variant Vigor2600Ge you purchased, the followingDSL service
must be available at your local premisses:
For Annex A : ADSL service must be enabled on your POTS telephone line.
For Annex B : ADSL service must be enabled on your ISDN telephone line.
(Vgior2600Ge provides Multimode which can automatically detect)

9
Local networking
To use the Ethernet port(s) you need at least:
One PC with an Ethernet Card installed.
One ethernet cat-5 UTP cable.
To use the Wireless LAN you need at least:
One PC with a Wireless LAN adaptor installed.
TCP/IP protocol suite
For TCP/IP, your PC can either be set to a static IP, or to get an IP automatically
(from a DHCP server).
The default gateway IP address of the router is 192.168.1.1. If static IP is chosen,
set your PCs IP address to 192.168.1.x, where xis any number in the range 2-254
inclusive.
Example:
VPI/VCI = 0/33
Protocol = PPPoA
Encapsulation Method = VCMUX
Modulation Method =G.dmt
Username/Password
Only for PPPoE/PPPoA mode users
Fixed IP Address/ Subnet Mask/ Gateway IP Address
Some ISP will use DHCP method to provide IP address for MPoA mode users,
then users do not need to know the fixed IP address.
If you do not know these information in detail, please contact your ISP to get
these informations.
How to Connect
the Router

10
Install Router Tools This tool which provides “Smart StartWizard” Firmware Upgrade Program and
TFTP client is in the enclosed CD. It supportsWindows, Mac OS 8/9 and Mac
OS X. Moreover, it provides “Syslog Tool” for Windows system.
Turn on your router Once all previous steps are completed, turn on your router. After Power is on,
theACT LEDwill blink and corresponding LAN port LED will light.
If the LEDs do not light normally, please refer to section A, “Trouble Shooting” for
furthur information.
Connect the blue Ethernet cable between Vigor 2600Ge ports P1/P2/P3/P4 and
any wired PCs.
Connect ADSL port to your ADSL-enabled telephone line. Remember that a
Line Filter should be used for any telephones or fax machines also connected to
theADSL telephone line.
Connect AC Power adaptor to Power socket.
Ethernet port (between router and PC), DSL port, and Power port as below:
The wire installation