Draytek Vigor2900V User manual

Vigor2900V series Quick Installation Guide
Trademarks
Copyright
Declarations
Copyright Information
Copyright 2004 All rights reserved. This publication contains information that
is protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
The following trademarks are used in this document:
lMicrosoft is a registered trademark of Microsoft Corp.
lWindows, Windows 95, 98, Me, NT, 2000, XP and Explorer are trademarks of
Microsoft Corp.
lApple and Mac OS are registered trademarks of Apple Computer Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Safety Instructions and Approval
Safety
Instructions
lRead the installation guide thoroughly before you set up the router.
lThe router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
lDo not place the router in a damp or humid place, e.g. a bathroom.
lThe router should be used in a sheltered area, within a temperature range of +5
to +40 Celsius.
lDo not expose the router to direct sunlight or other heat sources. The housing
and electronic components may be damaged by direct sunlight or heat sources.
lKeep the package out of reach of children.
lWhen you want to dispose of the router, please follow local regulations on
conservation of the environment.
Warranty We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of three (3) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.

European
Community
Hereby, we declare that the router is in compliance with the essential
requirements and other relevant provisions of R&TTE Directive 99/5/EC. The
Vigor 2900VG/VGi is designed for the WLAN 2.4Ghz network throughout EC
region, Switzerland, and the restrictions of France.
Be a Registered
Owner
Web registration is preferred. You can register your Vigor router via http://
www.draytek.com/. Alternatively, fill in the registration card and mail it to the
address found on the reverse side of the card.
Firmware & Tools
Updates
Due to the continuous evolution of DrayTek ADSL & Router technology, all
routers will be regularly upgraded. Please consult the DrayTek web site for
more information on newest firmware, tools and documents.
http://www.draytek.com/

1
1
2
3
7
Table of Contents
1. Introduction .............................................................................................
1.1 Brief Overview ...................................................................................
1.2 Highlights ..........................................................................................
1.3 Front Panel LEDs and Rear Panel Interfaces .......................................
1.4 Package Contains ..............................................................................
2. Quick Install Your Vigor2900V series Router ...............................
2.1 Hardware Installation ........................................................................
2.2 Configure Your Router via Quick Start Wizard ...................................
3. Wireless LAN Settings ........................................................................
3.1 General Settings .................................................................................
3.2 Security Settings .................................................................................
3.3 Access Control ..................................................................................
4. VoIP Settings ..........................................................................................
4.1 Dial Plan Setup ..................................................................................
4.2 SIP Related Function Setup ................................................................
4.3 Calling Scenario .................................................................................
5. Trouble Shooting ...................................................................................
5.1 Is the Hardware Status OK? ...............................................................
5.2 Are the Network Connection Settings on Your PC OK? ......................
5.3 Can You Ping the Router from PC? ....................................................
5.4 Are the ISP Settings OK? ...................................................................
5.5 Report to ISP and Dealer for Further Technical Support .......................
8
8
9
18
18
19
20
22
22
23
24
25
27
13
13
15
17

1
1. Introduction
The Vigor2900V series router, an Internet access solution for your LAN, which provides
you the shared web surfing and countless value-added features, such as Firewall / Security,
VPN, VoIP, USB interface printer server support, and 802.11g Wireless LAN(up to
54Mbps for Vigor2900VG/VGi only). These are all in a reliable one-box solution.
1.1 Brief Overview
VoIP
Wireless AP
Broadband Router
*
*
Vigor2900VG
*
*
*
Vigor2900V
-
Vigor2900VGi Vigor2900Vi
- -
ISDN Backup
*
*
*
*
*
*
*
-

2
1.2 Highlights
VoIP
lG.168 Line Echo-cancellation
lGain Control
lJitter Buffer (125ms)
lVoice Codec: G.711 A/u law, G.726, G.723.1,
G.729 A/B, VAD/CNG
lTone Generation and Detection: DTMF, Dial,
Busy, Ring Back, Call Progress
lProtocol: SIP, MGCP, RTP/RTCP (Note: The
first stage will implement SIP only, the other
protocols will be included later.)
Wireless Access Point (Vigor2900VG/VGi only)
l802.11g support (54Mbps data rate)
lBackward compatible with 802.11b device
lWireless security:
.Secure VPN over WLAN
.WPA Support
.802.1x User Authentication
.64/128 bits WEP wireless encryption
.Client MAC-address locking
.SSID stealth
WAN
lOne 10/100M Base-TX port with a RJ-45
connector
lDHCP client for cable service
lStatic IP address assignment for fixed IP
networks
lPPPoE/PPTP client for ADSL service
LAN
l4 port 10/100 Base-TX Ethernet switch with
VLAN
lDHCP server for IP assignment (up to 253 users)
lDNS cache and proxy
lNAT (Network Address Translation)
lVirtual server via port redirection or open port
lPort-based rate throttling capability
lRouting support: RIPv2, Static Route
Printer Server
lOne USB port connector
lBuilt-in LPD printer server
lProvide Win98/98SE/ME LPR printer driver
lCompatible with Win2000/XP/MacOS 9/MacOS
X built-in LPR printer driver
Firewall
lStateful Packet Inspection
lSelectable DoS/DDoS protection
lIP address anti-spoofing
lUser-configurable packet filtering
lNAT/PAT with Port Forwarding/Redirection &
DMZ
lE-mail alerting mechanism
Virtual Private Network (VPN)
lUp to 32 simultaneous VPN tunnels
lDial-in or dial-out, LAN-to-LAN or Teleworker-to-
LAN
lProtocol support for PPTP, IPSec, L2TP, L2TP over
IPSec
lAES, MPPE, and hardware- based DES/3DES
Encryption
lAuthentication support for MD5 and SHA-1
lIKE key management
lInteroperable with other leading 3rd party vendor
VPN devices or software
Flexible URL Content Filtering
lPreclude web surfing from using directly IP address
lURL blocking by user-defined keywords
lJava/ActiveX/cookies/proxy blocking
lExecutable/compressed/multimedia files blocking
lTime schedule support
Bandwidth Management facilities
lClass-based bandwidth guarantee by user-defined
traffic categories
lProvision of inbound/outbound bandwidth control
lSupport of eight priority-levels
lSupport of DiffServ-Codepoint marking
Application Support
lWindows Messenger, Yahoo Messenger, MSN
Messenger V6.0, NetMeeting, ICQ2001b/2002a,
most online gaming, and other multimedia
applications
lUPnP protocol support
Router Management
lWeb-based User Interface
lCommand line interface (Telnet)
lTelnet remote access support
lSNMP agent with MIB-II
lBuilt-in diagnostic tools
lRemote firmware upgrade
lQuick Start Wizard
lSyslog Monitoring
ISDN Facilities
lCompatible with Euro ISDN
lAutomatic ISDN backup
lSupport for 64/128kbps (multilink-PPP)
lBandwidth on demand (automatically switches
between 64kbps and 128kbps)
lLAN-to-LAN connectivity
lRemote Activation

3
1.3 Front Panel LEDs and Rear Panel Interfaces
1.3.1 Vigor2900V
LED Indicators Descriptions
ACT (Activity)
(P1, P2, P3, P4)
LAN
Phone
(FXS1,FXS2)
QoS
VPN
Printer
WAN
blinking
on
on
on
blinking
on
orange
green
blinking
orange
green
The router is powered on and running properly.
The QoS function is active.
The phone is off hook (the handset of phone is picked up).
A phone call is incoming
The VPN function is active.
The USB interface printer is ready.
Anormal 10Mbps WAN link is ready.
Anormal 100Mbps WAN link is ready.
Anormal 10Mbps connection is through its corresponding port.
Anormal 100Mbps connection is through its corresponding port.
Ethernet packets are transmitting.
Status
Connect to the USB printer.
Connect the included power adapter to the power outlet.
Connect to the analog phone for VoIP communication.
Connect to the local networked devices.
Connect the cable/DSL modem to access the Internet.
Descriptions
Rear Panels
Printer
PWR
Factory Reset
P1, P2, P3, P4
WAN
FXS1, FXS2
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and keep for
more than 5 seconds. When the ACT LED begins to blink rapidly, release the
button. Then the router will restart with the factory default configuration.
blinking Ethernet packets are transmitting.

4
1.3.2 Vigor2900VG
LED Indicators Descriptions
ACT (Activity)
(P1, P2, P3, P4)
LAN
Phone
(FXS1,FXS2)
QoS
WLAN
Printer
WAN
blinking
on
on
on
blinking
on
blinking
orange
green
The router is powered on and running properly.
The QoS function is active.
The phone is off hook (the handset of phone is picked up).
A phone call is incoming
The USB interface printer is ready.
Anormal 10Mbps connection is through its corresponding port.
Anormal 100Mbps connection is through its corresponding port.
Ethernet packets are transmitting.
Status
Connect to the USB printer.
Connect the included power adapter to the power outlet.
Connect to the analog phone for VoIP communication.
Connect to the local networked devices.
Connect the cable/DSL modem to access the Internet.
Descriptions
Rear Panels
Printer
PWR
Factory Reset
P1, P2, P3, P4
WAN
FXS1, FXS2
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and keep for
more than 5 seconds. When the ACT LED begins to blink rapidly, release the
button. Then the router will restart with the factory default configuration.
The Wireless LAN function is enabled.
Data packets are transmitting over Wireless LAN.blinking
orange
green
Anormal 10Mbps WAN link is ready.
Anormal 100Mbps WAN link is ready.
blinking Ethernet packets are transmitting.

5
1.3.3 Vigor2900VGi
LED Indicators Descriptions
ACT (Activity)
(P1, P2, P3, P4)
LAN
Phone
(FXS1,FXS2)
ISDN
WLAN
Printer
WAN
blinking
on
on
on
blinking
on
blinking
orange
green
The router is powered on and running properly.
The phone is off hook (the handset of phone is picked up).
A phone call is incoming.
The USB interface printer is ready.
Anormal 10Mbps connection is through its corresponding port.
Anormal 100Mbps connection is through its corresponding port.
Ethernet packets are transmitting.
Status
Connect to the USB printer.
Connect the included power adapter to the power outlet.
Connect to the analog phone for VoIP communication.
Connect to the local networked devices.
Connect the cable/DSL modem to access the Internet.
Descriptions
Rear Panels
Printer
PWR
Factory Reset
P1, P2, P3, P4
WAN
FXS1, FXS2
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and keep for
more than 5 seconds. When the ACT LED begins to blink rapidly, release the
button. Then the router will restart with the factory default configuration.
The Wireless LAN function is enabled.
Data packets are transmitting over Wireless LAN.blinking
The ISDN network is correctly setup.
blinking Asuccessful remote connection on the ISDN BRI B1/B2 channel.
orange
green
Anormal 10Mbps WAN link is ready.
Anormal 100Mbps WAN link is ready.
blinking Ethernet packets are transmitting.

6
1.3.4 Vigor2900Vi
LED Indicators Descriptions
ACT (Activity)
(P1, P2, P3, P4)
LAN
Phone
(FXS1,FXS2)
ISDN
VPN
Printer
WAN
blinking
on
on
on
blinking
on
blinking
blinking
orange
green
The router is powered on and running properly.
The phone is off hook (the handset of phone is picked up).
A phone call is incoming.
The USB interface printer is ready.
Ethernet packets are transmitting.
Anormal 10Mbps connection is through its corresponding port.
Anormal 100Mbps connection is through its corresponding port.
Ethernet packets are transmitting.
Status
Connect to the USB printer.
Connect the included power adapter to the power outlet.
Connect to the analog phone for VoIP communication.
Connect to the local networked devices.
Connect the cable/DSL modem to access the Internet.
Descriptions
Rear Panels
Printer
PWR
Factory Reset
P1, P2, P3, P4
WAN
FXS1, FXS2
Restore the default settings.
Usage: Turn on the router (ACT LED is blinking), press the hole and keep for
more than 5 seconds. When the ACT LED begins to blink rapidly, release the
button. Then the router will restart with the factory default configuration.
The ISDN network is correctly setup.
blinking Asuccessful remote connection on the ISDN BRI B1/B2 channel.
The VPN tunnel is launched.
orange
green
Anormal 10Mbps WAN link is ready.
Anormal 100Mbps WAN link is ready.

8
Caution Each of the FXS ports can be connected to an analog phone only. Do not connect
the FXS ports to the telephone wall jack. This connection might damage your router.
2.1 Hardware Installation
2. Quick Install Your Vigor2900V series Router
Before starting to configure the router, you have to connect your devices correctly.
1. Connect the WAN interface to the external ADSL/Cable modem with a RJ-45 cable.
2. Connect one port of 4-port switch to your computer with a RJ-45 cable.
3. Connect the attached power adapter to the power port.
4. Check the ACT and WAN, LAN LEDs to assure network connections. (For detailed LED
status explanation please refer to section 1.3)
Connection scenario is shown as below:

9
2.2 Configure Your Router via Quick Start Wizard
Step1 Open the web browser on a PC which is connected to the router and then link
to the gateway IP address of the router (the default setting is 192.168.1.1).
Once your Connection (http://192.168.1.1) is successful, a pop-up window
will open to ask for username and password. Leave the default null value and
press OK to continue.
(Note: If you fail in access to the web configuration, please refer to section 5 “Trouble Shooting” )
Step2 The Main Menu will appear after completing the last step. Click Quick Start
Wizard item in “Basic Setup” Group.(The following figure is in the instance
of Vigor2900VG)

10
Step3 Now Quick Start Wizard is launched on. Enter login password. Then click Next
to continue.
Step4 Select the appropriate time zone for your location. Then click Next to continue.
Step5 Select the appropriate connection type to connect to your ISP. Then click Next
to continue.

11
b. PPTP
Fill out all the information originally provided by your ISP. Then click Next to go to
Setp6.
c. Static IP
Enter the IP address information originally provided by your ISP. Then click Next to
go to Setp6.
a. PPPoE
Enter the username and password provided by your ISP. Then click Next to go to
Setp6.

12
Step6 This screen appears to indicate that your setup is complete. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.
d. DHCP
If your ISP requires you to enter a specific host name or specific MAC address, please
enter it in. Then click Next to go to Setp6.

13
This section will guide you how to operate the capabilities of Wireless LAN on the
router. Use the following setup links on the configuration Main Menu to setup
Wireless LAN functions.
Basic Setup > Wireless LAN Setup
The Frequency Domain is set as Europe and the MAC address is shown as above.
(The default value of Frequency Domain was set by factory depends on the reselling
region.)
Click General Settings to configure the Service Set Identifier (SSID) and wireless
channel.
3.1 General Settings
3. Wireless LAN settings

14
1. Enable Wireless LAN: Check the box to enable wireless function.
2. Mode: Select an appropriate wireless mode.
- Mixed (11b+11g): The radio can support both IEEE802.11b and
IEEE802.11g protocols simultaneously.
- 11g-only: The radio only supports IEEE802.11g protocol.
- 11b-only: The radio only supports IEEE802.11b protocol.
3. Scheduler: Set the wireless LAN to work at some time interval only. You may
choose up to 4 schedules from the 15 schedules which are defined under
Advanced Setup > Call Schedule Setup. Please refer to the detailed manual
on the attached CD. The default setting is always working.
4. SSID and Channel: The default SSID is “default”. We suggest you change it
to a particular name. In this case, SSID was changed to “DrayTek”.
- SSID (Service Set Identifier): It is used to name the wireless LAN, and
must be the same content in client PC/notebook wireless card(s). SSID can
be any text numbers or various special characters.
- Channel: Awireless channel for the router. The default channel is 6. You
can change it to more appropriate one if the selected channel is under
serious interference.
5. Hide SSID: Check it to prevent from wireless sniffing and make it harder for
unauthorized clients to join your wireless LAN.
6. Click OK to save settings.

15
3.2 Security Settings
Click Security Settings to configure the security options.
1. Mode: Select an appropriate encryption to improve the security and
privacy of your wireless data packets.
- Disable: Turn off the encryption mechanism.
- WEP Only: Accepts only WEP clients and the encryption key should
be entered in WEP Key.
- WEP/802.1x Only: Accepts only WEP clients and the encryption key
is got dynamically through 802.1x.
- WEP or WPA/PSK: Accepts WEP and WPA clients simultaneously
and the encryption key should be entered in WEP Key and PSK
respectively.
- WEP/802.1x or WPA/802.1x: Accepts WEP and WPA clients
simultaneously and the encryption key is got dynamically through
802.1x.
- WPA/PSK Only: Accepts only WPA clients and the encryption key
should be entered in PSK.
- WPA/802.1x Only: Accepts only WPA clients and the encryption key
is got dynamically through 802.1x.

16
NOTE: You should also set RADIUS Server simultaneously if WEP/802.1x
or WPA/802.1x , WEP/802.1x Only or WPA/802.1x Only mode is
selected.
2. WPA Encryption:
-The WPA encrypts each frame transmitted from the radio using the pre-
shared key (PSK) which entered from this panel or a key got dynamically
through 802.1x.
Pre-Shared Key (PSK): Either 8~63 ASCII characters or 64 Hexadecimal
digits leading by 0x can be entered. For example “0123456789ABCD....” or
“0x321253abcde.....”.
3. WEP Encryption:
- 64-Bit: For 64bits WEP key, either 5 ASCII characters or 10 hexadecimal
digitals leading by 0x can be entered. For example, ABCDE or
0x4142434445.
- 128-Bit: For 128bits WEP key, either 13 ASCII characters or 26
hexadecimal digits leading by 0x can be entered. For example,
ABCDEFGHIJKLM or 0x4142434445464748494A4B4C4D.
NOTE: 128 bits WEP is most secure, but has more encryption/decryption
overhead. Note that all wireless devices must support the same WEP
encryption bit size and have the same key. Four keys can be entered here,
but only one key can be selected at a time. The keys can be entered in ASCII
or Hexadecimal. Click the circle under Use next to the key you wish to use.
4. Click OK to save settings.

17
3.3 Access Control
For additional security, Access Control allows restricting the network access to a
list of pre-determined network clients.
1. Enable Access Control: Check the box to turn the function on.
2. MAC Address: Specify MAC Address which could be added on, removed from
or edited from the access list above.
3. Clean All: Clean all of configured MAC address on the list.
OK: Save the access control list.