Dream On Me 626 User manual

1
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 23 3/4 INCHES BY 37 3/4
INCHES WITH A THICKNESS NOT EXCEEDING
2 INCHES.
WARNING:
****KEEP INSTRUCTIONS FOR FUTURE USE****
THIS PRODUCT MEETS OR EXCEEDS SPECIFICATIONS AS ISSUED
BY THE CONSUMER PRODUCT SAFETY FOR NON-FULLSIZE BABY
CRIBS.
CAUTION:BEFORE USING THIS UNIT RECHECK ALL SCREWS TO
BE SURE THEY ARE TIGHTENED SECURELY. A PERIODIC CHECK
SHOULD BE MADE OF ALL SCREWS&NUTS TO BE SURE THEY
REMAIN TIGHT.
INFANTS CAN SUFFOCATE.
* IN GAPS BETWEEN A MATTRESS TOO SMALL OR TOO THICK AND
PRODUCT SIDES.
* ON SOFT BEDDING NEVER ADD A MATTRESS. PILLOW
COMFORTER, OR PADDING.
MADE IN CHINA
3 IN 1 CONVERTIBLE
PORTABLE CRIB
STYLE NO: 626
DREAM ON ME INC.
125 HELEN STREET
S.PLAINFIELD NJ 07080
908-791-0555

2
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.SUFFOCATION
HAZARD-TO HELP PREVENT SUFFOCATION FROM ENTRAPMENT.
WE RECOMMEND A DREAM ON ME MATTRESS/PAD.
DO NOT USE PLASTIC SHIPPING BAG OR OTHER PLASTIC FILM AS
MATTRESS COVERS NOT SOLD AND INTENDED FOR THAT
PURPOSE. THEY CAN CAUSE SUFFOCATION.
DO NOT PLACE PRODUCT NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES CAN STRANGLE A CHILD. STRINGS CAN
CAUSE STRANGULATION!
DO NOT PLACE ITEMS WITH A STRING AROUND A CHILD'S NECK.
SUCH AS HOOD STRINGS OR PACIFIER CORDS.
DO NOT SUSPEND STRINGS OVER A PRODUCT OR ATTACH
SPRINGS TO TOYS.
DO NOT TIE PACIFIERS, NECKLACES ORANY OTHER ITEMS
AROUND A CHILD'S NECK OR ON THE PRODUCT PARTS.
BEFORE EACH USAGE OR ASSEMBLY, INSPECT PRODUCT FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE PRODUCT IF ANY PARTS ARE
MISSING OR BROKEN. ASK YOUR DEALER OR WRITE TO DREAM
ON ME. FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS. THE
PRODUCT, INCLUDING SIDE RAILS,MUST BE FULLY ERECTED
PRIOR TO USE.MAKE SURE LATCHES ARE SECURED.
DO NOT LEAVE CHILD IN PRODUCT WITH SIDE LOWERED. BE
SURE SIDE IS IN RAISED AND LOCKED POSITION WHENEVER
CHILD IS IN CRIB. REPLACE TEETHING RAIL IF DAMAGED.
CRACKED OR LOOSE.DISCONTINUE USE OF THE PRODUCT
WHEN CHILD IS ABLE TO CLIMB OUT REACHES THE HEIGHT OF
35 IN.(890MM).
WHEN CHILD IS ABLE TOPULL TO STANDING POSITION, REMOVE
BUMPER PADS. LARGE TOYS. AND OTHER OBJECTS THAT COULD
SERVE AS STEPS FOR CLIMBING OUT. WHEN CHILD IS ABLE TO
PULL TO STANDING POSITION, SET MATTRESS/BASE TO LOWEST
ADJUSTMENT POSITION AND REMOVE BUMPER PADS. LARGE
TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR
CLIMBING OUT.
DO NOT USE A WATER MATTRESS WITH THIS PRODUCT.
IF REFINISHING,USE ANONTOXIC FINISH SPECIFIED FOR
CHILDREN'S PRODUCTS.

3
e. Wood Dowel 8PCS
a. 3” Allen head Bolt 20 PCS
A. Top Rail (2PCS) B. Front Rail Bottom (1PC) C. Left Front
Leg (1PC)
G. Back Rail Bottom (1PC)
E. Left Back
Rail Leg (1PC)
J. Metal Spring Support Platform (1PC)
CONNECTION HARDWARE
b. Barrel Nuts 20 PCS
c. 3/4” Allen head Bolt 4 PCS
d. Allen Wrench 1 PCS
CRIB COMPONENTS
D. Right Front
Leg (1PC)
F. Right Back Rail Leg (1PC) H. Left Crib End (1PC)
I. Right Crib End (1PC) K. Mattress (1PC)

STEP 1
Insert wood dowels (e) into top rails (A).
A
e
e
STEP 2
I
F
D
Attach the right crib end (I) to the
right front leg (D) and the right
back leg (F) by using allen head
bolts (a) and barrel nuts (b) and
wood dowels (e). Then attach
the left crib end (H) to the left front
leg (C) and the left back leg (E) by
using allen head bolts (a) and
barrel nuts (b) and wood dowels(e).
e
e
a
aa
a
d
b
b
b
b
a
a
a
a
a
A
G
E
F
Attach the Top rail (A) and the
back rail bottom (G) to the left
back leg (E) by using allen
head bolts (a) and barrel nuts
(b) and wood dowel (e). Then
attach the Top rail (A) and the
back rail bottom (G) to the right
back leg (F) by using allen
head bolts (a) and barrel nuts
(b) and wood dowel (e)
e
e
b
b
b

5
STEP 4
c
c
c
J
E
C
D
F
Locate the metal spring (J)
with tabs.
Be sure the smooth side of
metal spring (J) is paced
upward. Position the tabs
of metal spring (J) to mount
to the selected position onto
the legs. Inlert the bolts (c) ,
through the tabs and into
thread insets onto the legs ,
then tighten securely with
Allen Wrench (d).
STEP 5
a
a
Attach the Top rail (A) and
the front rail bottom (B) to
the left front leg (C) by
using allen head bolts (a)
and barrel nuts (b) and
wood dowel (e). Then
attach the Top rail (A) and
the front rail bottom (B) to
the right front leg (D) by
using allen head bolts (a)
and barrel nuts (b) and
wood dowel (e).Last,Put the
mattress (K) into the bed.
a
a
a
a
C
D
B
A
b
b
K

6
Remove the top rail (A) and the front rail bottom (B) as shown.
CONVERT THE CRIB INTO TWIN BED
CONVERT THE CRIB INTO DAY BED
1.Remove the Metal Spring Support
Platform (J) .Then remove the right
crib end (I) and the left crib end (H).
2.Use the front panel as foot board
of the single bed.
3.Use the rear panel as head board
of the single bed.
4.connect the front and rear panels
by a standard hollywood frame
provided by others.
(FRAME RAIL NOT INCLUDED TO CONVERT TO TWIN BED)