Drive DeVilbiss Healthcare Enigma Expedition User manual

www.drivedevilbiss.co.uk
Expedition
Wheelchair

Expedition Wheelchair Owner’s Handbook (Page 1) Code: EXP002_IFU (Iss
5/17)

Expedition Wheelchair Owner’s Handbook (Page 2) Code: EXP002_IFU (Iss
5/17)
Contents
1. Contents
2. Introduction
3. Parts Description
4. Leg Rest Operation
5. Folding Back Mechanism
6. Disassembly and Folding
7. Using the Stepper pad
8. Brake Operation
9. Operation and Propulsion
10. Using a Lap Belt
11. Warranty
Introduction
The Enigma Expedition wheelchair is designed for occasional or frequent use,
and can be used indoors and outdoors. The wheelchair is designed for a
single user of up to 135kg (21 stone) for the standard models or 150kg (23.5
stone) for the heavy duty models. The wheelchair is available in either a
transit or self-propel model.
The wheelchair can be manually moved in forward and reverse and is
propelled by the carer or attendant pushing the wheelchair using the push
handles.

Expedition Wheelchair Owner’s Handbook (Page 3) Code: EXP002_IFU (Iss
5/17)
Parts Description

Expedition Wheelchair Owner’s Handbook (Page 4) Code: EXP002_IFU (Iss
5/17)
Leg Rest Adjustment
Flip the anti-rattle collar
lever (1) upwards and then
push in brass buttons (2).
Adjust the legrests to the
required height and until
they click in to position.
Flip the anti-rattle collar
lever (1) downwards.
Folding Back Mechanism
2
1
Push the black paddle towards the back post
with your thumb (1) whilst pulling the handle
down (2), as shown. Repeat this operation for
the other handle. To put the backrest back
into position, lift both handles together and
the folding mechanism will lock back
automatically.
Do not push down on the handles to raise the
front of the wheelchair, as this could result in
damage to the wheelchair. Use the stepper
pad as described later in the handbook.

Expedition Wheelchair Owner’s Handbook (Page 5) Code: EXP002_IFU (Iss
5/17)
Disassembly And Storage
This wheelchair has a number of quick release components and the
wheelchair frame is easily foldable to facilitate a light carry weight and
minimize storage space.
1. Half Folding Back.
Follow the previous instructions to fold the back.
2. Folding the wheelchair.
Grab the centre of the front and rear edges of the seat canvas. Pull
upwards on the seat sling and the wheelchair should naturally fold up.
IMPORTANT: The wheelchair has not been tested as a seat in a motor
vehicle. Users should always transfer to the vehicle’s seat and the
wheelchair should be safely stowed away.
3. Leg Rests
To install the leg rests, place
the leg rests on the two
posts mounted on the frame
(1). Swing the leg rests
inwards to lock in position.
To remove the leg rests,
press the chrome lever on
the leg rest and swing the
leg rest out. Lift up the leg
rest from the two posts to
remove.
1
2

Expedition Wheelchair Owner’s Handbook (Page 6) Code: EXP002_IFU (Iss
5/17)
Using The Stepper Pad
An attendant can use the stepper pad to raise the front castors (when
mounting a kerb for example). To use, push down on the stepper pad with a
foot. Do not raise the front castors by pushing down on the push handles as
this could result in damage to the wheelchair.
To mount a kerb.
Approach the kerb head on. Then the attendant uses the stepper pad to raise
the front castors, and lowers the front castors on the raised kerb. Finally the
attendant should push the wheelchair forward, lifting it up slightly to mount
the kerb if required.
To go down a kerb.
Line up the front castors with the edge of the kerb. The attendant uses the
stepper pad to raise the front castors and tip the user slightly back. Keeping
the castors raised, slowly lower the wheelchair down the kerb.

Expedition Wheelchair Owner’s Handbook (Page 7) Code: EXP002_IFU (Iss
5/17)
Brake Operation
Note: The brakes should only be
operated by the attendant.
Cable Brakes
To operate the brakes to slow the
wheelchair during motion, squeeze
both brake levers so they move up
(1). Release the lever to release the
brake.
To operate the brakes as a
temporary parking brake, push both
levers down (2) to lock the brake on.
To release the brakes, lift the brake
levers up.
Parking Brakes
If the wheelchair is stationary for a
long time or unattended, then apply
the parking brakes.
Push the parking brake lever back (as
shown by the arrow) to apply the
brake.
Push the lever forward to release the
brake.

Expedition Wheelchair Owner’s Handbook (Page 8) Code: EXP002_IFU (Iss
5/17)
Operation And Propulsion
!
Before Using the Wheelchair read the safety notices below:
Use slow speeds on gradients. Do not exceed the
maximum gradient stated.
The wheelchair is only suitable for single occupancy.
Keep your feet on the footplates when moving. Do not
stand on the footplates –they are designed only to be
used when the user is seated in the wheelchair.
Do not use escalators.
Do not reverse down a gradient
Maintain proper balance at all times. Users should not
move their centre of gravity out of the seating area.
Do not reach for items further than your arm will extend.
Be aware of hazards in your environment, such as narrow
doorways, steps, household appliances, children’s toys,
etc.
We recommend you consult your healthcare professional
for advice about transferring to and from the wheelchair.
The parking brakes should always be applied when
transferring.
Ensure that fingers and objects do not get caught in the
spokes of the rear wheels.
The transit wheelchair can only be propelled by an attendant. The attendant
should push the wheelchair from behind using the handgrips, and following
the safety advice above.
The self propel wheelchair can be propelled by an attendant (as directed
above) or the wheelchair user. The user can propel themselves by pushing on
the handrims attached to the side of the rear wheels, and slow themselves
down by applying pressure to the handrims.
When stationary the brakes should always be applied.

Expedition Wheelchair Owner’s Handbook (Page 9) Code: EXP002_IFU (Iss
5/17)
Using The Lap Belt
The lap belt is to restrain the wheelchair occupant during normal use. The
lap belt is not be used as a seat belt in a motor vehicle. Under no
circumstances should the Expedition wheelchair be used as a seat in a motor
vehicle (e.g. cars, buses, trains, etc).
The lap belt should be adjusted to suit each user. The length of the belt can
be adjusted by the tri-glides (as shown in the diagram overleaf). The lap belt
has a luggage-style large locking clip to fasten and unfasten the lap belt. To
fasten the lap belt, push the clip in to the receiver until it locks in the
position (which can be heard by an audible click).
When fastened, the lap belt should be tight around the user’s pelvis without
causing discomfort or undue pressure. This will help keep the user’s hips and
pelvis towards the back of the wheelchair. Use the tri-glides (shown) to adjust
the length of the lap belt. The length of the lap belt should be checked each
time the belt is used.
There is a risk of suffocation from users ‘submarining’ (where they slide down
the chair until the lap belt is around the neck area). To reduce the risk of this,
ensure that the lap belt is used under supervision and is used as instructed.
The lap belt may not be suitable for all users of wheelchairs. Seek professional
medical advice before using the lap belt.