Drive DeVilbiss Healthcare LAWC007A User manual

Ultra Lightweight Aluminium Wheelchair
(LAWC007A, LAWC008A,
LAWC011A, LAWC012A)
Instructions for use

Page 2 of 12Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1)
introduction
The Ultra Lightweight wheelchair range is intended to assist the
transport of users with mobility diculties. This wheelchair is designed
for occasional or frequent use, and can be used indoors and outdoors.
Over-loading the wheelchair is the only known contraindication,
although others may be specific to an individual or care environment.
The wheelchair can be manually moved forward and in reverse. The
wheelchair is available in either a transit model, or a self propel model
to be operated by the wheelchair user. The wheelchair can support
users of up to 125 kg (20 stone), depending on the model purchased.
parts description
PUSH
HANDLE
1/2 FOLD
BACK
MECHANISM
ARM REST
SIDE
PANEL
FOOTREST
FRONT
CASTOR
QUICK
RELEASE
PIN
24" WHEEL
& HANDRIM
STEPPER
TUBE
BRAKE
LEVER
PUSH
HANDLE
ARM
RESTSIDE
PANEL
BRAKE
FOOT
REST
FRONT
CASTOR
12.5"
WHEEL
Self Propel models
17” (LAWC007A)
20” (LAWC011A)
Transit models
17” (LAWC008A)
20” (LAWC012A)

Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1) Page 3 of 12
symbolspreparing for use
These instructions should be read carefully before using the wheelchair.
This product is not for user assembly and does not have a service manual.
The only parts to be fitted and adjusted are the footrests.
A risk assessment must also be performed to assess suitability of the device
for the user. This assessment should include, but not be limited to:
• Small adults (and children)
• Users (and attendants) who lack capacity
• Very active occupants
• Unauthorised access to the wheelchair
Independent users and attendants are responsible for determining that they
are both mentally and physically capable of using the wheelchair with
minimal risk of harm.
Maximum occupant mass
Exceeding the maximum occupant mass marked on your device can damage
the product and put users at risk of harm.
Remove all packaging and stand the wheelchair on the ground. Separate the
arm rests to open the wheelchair, then push down firmly. Once the seat is
secure, the backrest is upright and the footrests are attached (see overleaf),
the wheelchair is ready for use.
!
Warning
This wheelchair must not be used as a seat in a motor vehicle.
Users should always transfer to the vehicle's seat and the
wheelchair should be safely stowed away.

Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1) Page 4 of 12
footrest adjustment
1
2
To fit the footrests, place the brackets onto the
pins either side of the wheelchair frame (1) and
rotate inwards (2) until they lock into place. Pull
the tabs inwards to release.
For optimum comfort it is important to attain
the correct leg position. The footrests have
been designed so they can be extended into
one of 5 fixed lengths.
To change the height, unscrew the bolt on the
silver tubing with a 4mm hex key. Adjust the
footrest as required, then tighten to secure.
Attaching the footrest
!
Common misuse
Do not stand on the footrests. Overloading can damage the
product and cause harm to the occupant.
folding back mechanism
2
1
PADDLE
To fold the backrest, push the black paddle
towards the back post with your thumb (1)
whilst pulling the handle down (2) as shown
in the folding the backrest image. Repeat this
operation for the other handle.
To put the backrest back into position, lift
both handles together and the folding
mechanism will lock back automatically.
Do not push down on the handles to raise
the front of the wheelchair, as this could
result in damage to the wheelchair. To mount
kerbs and steps, reconnect the backrest and
use the stepper tube as described in the
steep terrain, kerbs and steps section.
Folding the
backrest
!
Common misuse
The paddle is intended to be pushed. Do not pull the paddle to
fold the backrest.

Page 5 of 12Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1)
transfer and use
!
Before using the wheelchair, read the safety notices below;
• Do not exceed the 10º maximum gradient. Use slow speeds
and do not reverse down a gradient.
• Do not use on escalators.
• The wheelchair is only suitable for single occupancy.
• Keep your feet on the footrests when moving. Do not stand on
the footrests.
• Ensure that fingers and objects do not get caught in the wheel
spokes or any other moving parts during use and assembly.
• Maintain proper balance at all times. Users should not move
their centre of gravity out of the seating area.
• Do not reach for items further than your arm’s length.
• Parking brakes should always be applied when transferring.
• Be aware of hazards in your environment, such as narrow
doorways, steps, household appliances, children’s toys, etc.
• A risk assessment must be performed by a competent person
to ensure the wheelchair is suitable for the user. We
recommend you consult a healthcare professional before using
any assistive medical devices.
• Keep away from heating and ignition sources which may raise
surface temperatures or cause a fire.
Transfer: When transferring in and out of the seat, move the seats as
close as possible to each other. Attendants should engage parking brakes and
fold away footrests. If users need to be lifted out of a seat, attendants are
responsible for being suitably trained and competent to lift occupants with
minimal risk of harm. Good health and safety practice must always be used.
Propelling: The attendant should push from behind using the handgrips,
and following the safety advice above. Transit models can only be propelled by
an attendant. Self Propel models can also be propelled by wheelchair users,
pushing the handrims on the rear wheels. To slow down, apply pressure to the
handrims.
When stationary, the brakes should always be applied.

Page 6 of 12Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1)
steep terrain, kerbs and steps
Steep terrain: These wheelchairs are not designed for use on gradients
beyond 10°. When on a slope, avoid swerving or sudden changes in movement.
Over kerbs: Attendants push down on the stepper tube with a foot to raise
the front castors (when mounting a kerb for example).
To mount, approach the kerb head-on. Then the attendant uses the stepper
tube to raise the front castors, and lowers the front castors on the raised kerb.
Finally the attendant should push the wheelchair forward, lifting it up slightly to
mount the kerb if required.
To go down, line up the front castors with the edge of the kerb. The attendant
uses the stepper tube to raise the front castors and tip the user slightly back.
Keeping the castors raised, slowly lower the wheelchair down the kerb.
Multiple steps: The wheelchair is not designed to mount staircases, so may
require carrying if no elevators or ramps are available. Attendants are
responsible for being suitably trained and competent to lift the wheelchair with
minimal risk of harm. Do not carry using the handles or any removable sections.
brake operation
Parking Brakes
To apply the parking brakes, push the handle on the brake unit until locked
in place. To release the brake, pull the handle in the opposite direction. The
brakes should always be applied when the wheelchair is stationary.
Cable Brakes
On the transit models, the attendant
pushing the wheelchair may use
cable-operated brakes to slow or park
the wheelchair.
To apply the brakes, squeeze the large
lever (A) on the push handles and the
brakes will be applied until the levers
are released. Ensure both levers are
pulled simultaneously to ensure the
wheelchair travels in a straight line.
Operating
the brakes
Transit only:
To lock, push the lock tab (B)
forward. Pull back to release.
!
Common misuse
Do not lean or push down on the push handles, as this can
damage the wheelchair.

Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1) Page 7 of 12
using a wheelchair belt
Belts are often used to restrain wheelchair occupants during normal use.
However, belts are not provided as standard with these models. Any belts
used should be adjusted to suit each user. When fastened, they should be
tight without causing discomfort or undue pressure. Belts may not be suitable
for all users. Seek professional medical advice before using a wheelchair belt.
Lap belts
Lap belts are secured around the user’s pelvis to help keep their hips and
pelvis towards the back of the seat. If lap belts are attached to this product,
they must not be used as a substitute for a seatbelt in a motor vehicle.
Drive DeVilbiss Healthcare Ltd provide a compatible lap belt (RT-716, shown
below) for all wheelchairs in the LAWC range. The length of the belt can be
adjusted using the tri-glides (as shown in the diagram) and it has a large
luggage-style locking clip to fasten and unfasten the lap belt.
There is a risk of suocation from users ‘submarining’ (where they slide down
the chair until the lap belt is around the neck area). To reduce the risk of this,
ensure appropriate belts are fitted, occupants are under supervision and the
belts are used in line with the manufacturer’s instructions for use.
RT-716 Safety Strap
Lap Belt (from Drive
DeVilbiss Healthcare Ltd)

Page 8 of 12Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1)
disassembly and storage
This wheelchair has a number of quick release components and the
wheelchair frame is easily foldable. This facilitates a light carry weight and
minimises storage space required
. To disassemble for storage, transport or
maintenance, follow the steps below. To reassemble components, reverse
these instructions.
1. Quick release wheel
On the self propel model, the rear wheels
can be removed. To remove the rear wheels,
push the button in the centre of the wheel
hub, (shown on the Quick release button
diagram in grey), and slide the wheel from
its axle.
2. Half Folding Back
Follow the previous instructions to fold the back.
3. Footrests
Follow the previous instructions to remove or swing out the footrests.
4. Folding the wheelchair
Grab the centre of the front and rear edges of the seat sling.
Pull upwards on the seat sling and the wheelchair should naturally fold up.
Note: The wheelchair may be folded and stored in a motor vehicle.
The wheelchairshould be stored in a dry environment, away from direct
sunlight.
Quick release
button

Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1) Page 9 of 12
care and maintenance
Do not use a damaged or badly worn wheelchair. Users should routinely check for
any malfunctions or changes in performance. See Accessories and Spare Parts
section for approved parts available from Drive DeVilbiss Healthcare Ltd.
• Before each use of the wheelchair, the brakes and tyres should be checked. It
can be folded up for storage, with the parking brakes on.
• The wheelchairshould be kept clean and dust free. This can be done with a
duster or damp cloth. Avoid neat bleach or abrasive surface cleaners. Leave to
fully dry before reuse.
• Drive DeVilbiss Healthcare Ltd recommends that an approved service engineer
maintains the wheelchair annually, and these items should be repaired,
replaced, adjusted and/or lubricated if required:
•When the product has reached the end of its useful life, follow local recycling
and disposal policies.
• Tyres
• Wheel bearings
•
•
Castors
• Brakes
•Footrest locking mechanism
Seat upholstery
•
•
Back upholstery
•
Arm pads
•
Rear wheel quick release pin
•
Half folding back mechanism
•
Back posts
Wheelchair folding mechanism
powerpack installation
This wheelchair is suitable for some retrofit
powerpacks, which allow the device to be
controlled electronically. (See Powerpack example
image.)
Powerpacks are not required to use the
wheelchair. The mounting position will need
adapting to be suitable for both the user and the
powerpack used.
Any installed powerpack must be
used in line with the manufacturer’s instructions
for use.
For more information about powerpacks, contact
Drive DeVilbiss Healthcare Ltd or your local dealer.
Powerpack
example

Page 10 of 12Ultra Lightweight Aluminium Wheelchair (LAWC_IFU 2020-11 rev1)
specification
Model LAWC007A LAWC008A LAWC011A LAWC012A
Maximum
occupant mass 115 kg 115 kg 125 kg 125 kg
Overall length with
footrest 107 cm 95 cm 109 cm 95 cm
Overall width 62 cm 61 cm 71 cm 66 cm
Folded length 74 cm 65 cm 79 cm 65 cm
Folded width 32 cm 28 cm 32 cm 28 cm
Folded height 71 cm 73 cm 73 cm 73 cm
Total mass 12.9 kg 11.5 kg 13 kg 11.6 kg
Mass of heaviest
part 7.8 kg 10.2 kg 8 kg 10.4 kg
Static stability 10° 10° 10° 10°
depth
Eective seat
Eective seat
39 cm 39 cm 39 cm 39 cm
width 42 cm 42 cm 51 cm 51 cm
Seat surface height
at front edge 52 cm 52 cm 52 cm 52 cm
Overall height 93 cm 97 cm 93 cm 97 cm