Drive Medical Cruiser II User manual

cruiser II wheelchair
www.drivemedical.com
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
Rev.1.11.17.16
Your Drive branded product is warrantied to be free of
defects in materials and workmanship for the lifetime of
the product for the original consumer purchaser.
This device was built to exacting standards and care-
fully inspected prior to shipment. This Lifetime Limited
Warranty is an expression of our confidence in the mate-
rials and workmanship of our products and our assur-
ance to the consumer of years of dependable service.
This warranty does not cover device failure due to owner
misuse or negligence, or normal wear and tear. The
warranty does not extend to non-durable components,
such as rubber accessories, casters, and grips, which are
subject to normal wear and need periodic replacement.
If you have a question about your Drive device or this
warranty, please contact an authorized Drive dealer.
Warning: The items and packaging in this shipment contain
chemicals known to the state of California to cause cancer,
birth defects or other reproductive harm.
*This product meets or exceeds all federal safety and envi-
ronmental regulations.
© 2016 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China
lifetime limited
warranty

CAUTION:
Stability - Wheelchair is designed to be safe and stable as
long as center of gravity is maintained while going about
normal activities. Care must be taken while performing
activities that shift your center of gravity in the chair.
Never reach so far that require you to shift in the seat or
bend over out of the chair. When you have to reach for
objects that require you to lean, be certain front casters
are pointing in a forward position that extends the wheel
base and will stabilize the chair, and the wheel locks are
in the locked position.
Ramps - Be sure of your own capabilities, limitations and
strength before attempting to go up a ramp. Correct
techniques on ramp negotiation should be shown to you
by a qualified professional. Assistance is recommended
when going up or down inclines greater than 10o. If you
must stop on an incline, avoid sudden, abrupt movement
when you resume movement. Because of backward
angle of the chair, sudden abrupt movement could cause
instability. Attempting to use the wheel lock brakes could
result in accidental locking, tipping to one side, or cause a
sudden stop. Avoid changing direction when going down
an incline, as this could result in instability of tipping over.
Please read this manual carefully to insure safe usage and
understanding of maintenance instructions.
Congratulations on your purchase of a Drive wheelchair.
Drive wheelchairs are a product of quality engineering and
are manufactured to meet our own highly rigid specifica-
tions and will surpass all your expectations.
back upholstery
armrest
side panel
front rigging
foot plate
fork
wheel lock
caster wheel
handrim
rear wheel
handgrip
WHEELLOCKS - Engage both wheel locks before
getting in or out of chair, leaning forward in chair,
or while in an elevator or wheelchair lift. Locks are
engaged by pushing handle completely forward.
Adjustments to locks are made by loosening or tight-
ening nut on the carriage bolt. Embed lock shoe at
least 1/8” by sliding clamp toward rear wheel while
handle is engaged in locked position. Tighten nut
and bolt to secure in position. Test for correct lock-
ing action before actual use.
TIRES - Solid rubber tires need minimal mainte-
nance, but should be cleaned occasionally with a
damp cloth. Replace if tires become severely worn
or cracking appears.
FRONT CASTERS - Casters should be checked
periodically and lubricated occasionally. Lubricate
by removing fork and greasing caster stem bearings.
Lubricate wheel bearings by removing wheel from
fork. Reassemble fork and wheel by tightening nuts
until no play remains, but wheels roll freely. If nut is
too loose, caster will shimmy, if too tight, chair will
be hard to steer.
REMOVAL OF SWINGAWAY FOOT RESTS/LEG
RESTS- Release lock by pushing on the front rigging
lever. Swing-away foot rest /leg rest out and side-
ways. Lift to remove.
ADJUSTINGLENGTHOFFOOTREST/LEGREST-
When adjusting length of foot rests or leg rests, user
should be sitting in wheelchair with feet on the foot
plates. Loosen bolt on the clamp around support
assembly. Raise or lower foot plate to desired posi-
tion that will provide maximum support of thighs.
Use and Safety

Front rigging should not be so low that it causes
uncomfortable pressure to thighs at front of seat
upholstery. Footrest should not be lower than 2-1/2”
from the ground to ensure clearance.
ADJUSTING/ELEVATING LEG REST - Lift foot
plate on leg rest assembly to desired position.
Release leg rest assembly and it will automatically
lock into place. To lower, push out on leg rest lever
and lower foot plate to desired position.
WHEELS - Large rear wheels should be inspected
at least once a month to ensure proper tightness.
If wheel wobbles or is loose, release lock nut and
tighten axle bolt slightly. Test for proper tightness
by leaning chair to one side and spin adjusted wheel.
GENERALCARE - Wipe chrome parts with a clean,
soft cloth at least once a week. All metal parts can
be cleaned with auto wax or similar products. If
exposed to moisture, dry immediately. Do not use an
abrasive cleanser that will scratch the finish.
TO OPEN CHAIR - Open wheelchair by tilting to
one side and pushing down on seat rail until fully
opened.TOCLOSE/FOLDCHAIR - First fold foot
plates to vertical position. Grab seat with both
hands at front and back edge and lift. Or, tilt
chair to one side and lift up on seat rail.
REMOVABLEARMS - Remove arms by depress-
ing spring button and lifting arms out of front
and rear sockets.
WARNING
Do not attempt to adjust or operate wheelchair
without reading carefully all instructions in this
manual.
This wheelchair has not been approved as a
seat that can be used within vehicles of any
kind. Always transfer wheelchair user to a
vehicle manufacturers approved seat and use
safety restraints available.
Do not operate this wheelchair on roadways,
streets or any surfaces with vehicular traffic.
Do not attempt to operate on inclines 10oor
greater without proper assistance.
Be sure to completely engage wheel locks
when getting in and out of wheelchair or when
in elevator or wheelchair lift.
Wheelchair should be on a smooth, stable and
level area with wheel locks engaged before
transferring user in or out of wheelchair.
Do not adjust foot rests any lower than 2-1/2”
from floor.
When getting in or out of wheelchair, do not
stand on or apply weight to foot rests.
Before reaching or leaning forward, rotate cast-
ers to front of the wheelchair engage wheel
locks to help prevent wheelchair from tipping
over.
Do not lean over or apply weight to the top of
wheelchair back. This can cause wheelchair
to tip over. When trying to extend arms over
back, only reach as far as your arm can extend
without having to alter your seating position.
DO NOT stand on wheelchair.
DO NOT use wheel locks to slow your descent
down an incline.
Abruptly changing directions while going down
an incline could cause instability or possible
tipping over.

1. Lay wheelchair on its back. Open seat two-thirds of
the way so seat posts do NOT rest on chair frame.
Unfold seat extension by pulling upward on end of
seat to release the hook and loop fastener.
2. Pull outward on hook and loop straps to free them
from underside of seat.
Your Cruiser II Wheelchair comes with an adjustable depth
seat that has been factory set at the shortest position.
Follow the instructions below to extend the seat depth of
your chair.
seat extension
instructions
3. The seat extension post is located inside the seat
frame. To access it, remove the screw closest to the
edge of the seat that secures the seat upholstery to
the frame of the chair by turning it counter-clockwise.
4. Pull outward on seat extension post until the second
hole on the post lines up with the hole on the seat
frame. Re-insert the screw into the seat upholstery
and frame by turning clockwise to secure in place.
5. Fold hook and loop closure strap over extended seat
post to secure seat upholstery to the frame.
6. Repeat steps 3 – 5 on the opposite side.
7. Return chair to upright position and push down on
seat to secure it to the frame.