Dsc Pc-link9 User manual

INSTALLATION

MANUAL

PC15OO

Notice:Notice:

Notice:

The Canadian Department of Communications label

identifies certified equipment. This certification means that

the equipment meets certain telecommunications network

protective, operational and safety requirements. The

Department does not guarantee the equipment will operate

to the user's satisfaction.

Before installing this equipment, users should ensure that it

is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be

installedusinganacceptablemethodofconnection.Insome

cases, the company's inside wiring associated with a single

lineindividualservicemaybeextendedbymeans of certified

connectorassembly(telephoneextensioncord).Thecustomer

should be aware that compliance with the above conditions

may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an

authorized Canadian maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to

disconnect the equipment.

User should ensure for their own protection that the electrical

ground connections of the power utility, telephone lines and

internal metallic water pipe system, if present, are connected

together. This precaution may be particularly important in

rural areas.

Caution:Caution:

Caution:

Usersshouldnotattempttomakesuchconnections

themselves, but should contact the appropriate electric

inspection authority, or electrician, as appropriate.

The

Load Number

(LN) assigned to each terminal device

denotes the percentage of the total load to be connected to

a telephone loop which is used by the device, to prevent

overloading. The termination on a loop may consist of any

combination of devices subject only to the requirement that

the total of the Load Numbers of all the devices does not

exceed 100.

The Load Number of this unit is 42.

AVIS:AVIS:

AVIS:

L'étiquette du ministère des Communications du

Canadaidentifielematérielhomologué.Cetteétiquettecertifie

quelematérielestconformeàcertainesnormesdeprotection,

d'exploitation et de sécuritédes réseaux de

télécommunications. Le Ministère n'assure toutefois pas que

le matétiel fonctionnera àla satisfaction de l'utilisateur.

Avantd'installercematériel,l'utilisateurdoits'assurerqu'ilest

permis de le raccorder aux installations de l'entreprise locale

detélécommunication.Lematérieldoitégalementêtreinstallé

en suivant une méthod acceptée de raccordement. Dans

certains cas, les fils intérieurs de l'entreprise utilisés pour un

service individuel a ligne unique peuvent être prolongés au

moyen d'un dispositif homologuéde rassordement (cordon

prolongateur tèlèphonique interne). L'abonnéne doit pas

oublier qu'il est possible que la conformitéaux conditions

énoncées ci-dessus n'empechent pas la dégradation du

servicedanscertainessituations.Actuellement,lesentreprises

de télécommunication ne permettent pas que l'on raccorde

leur matériel a des jacks d'abonné, sauf dans les cas précis

prévus par les tarrifs particuliers de ces entreprises.

Lesréparationsdematérielhomologuédoiventetreeffectuées

par un centre d'entretien canadien autorisédésignépar le

fournisseur. La compagnie de télécommunications peut

demander àl'utilisateur de débrancher un appareil àla suite

deréparations oudemodifications effectuéesparl'utilisateur

ou àcause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous

lesfilsdemiseàlaterredelasourced'énergieélectrique,des

lignes téléphoniques et des canalisations d'eau métalliques,

s'il y en a, sont raccordés ensemble. Cette précaution est

particulièrement importante dans les régions rurales.

AVERTISSEMENT:AVERTISSEMENT:

AVERTISSEMENT:

L'utilisateur ne doit pas tenter de faire

ces raccordements lui-meme; il doit avoir recours a un

service d'inspection des installations électriques, ou a

electricien, selon le cas.

L'indice de charge

(IC) assignéa chaque dispositif terminal

indique, pour éviter toute surcharge, le pourcentage de la

chargetotalequipeutetreraccordéeauncircuittéléphonique

boucléutilisépar ce dispositif. La terminaison du circuit

bouclépeut etre constituée de n'import quelle combinaison

de dispositifs, pourvu que la somme des indices de charge

de l'ensemble des dispositifs ne dépasse pas 100.

L’Indice de charge de cet produit est 42.

This manual is for the PC1500 software version 4.0

CANADIAN DEPARTMENT OF COMMUNICATIONS NOTICE

TABLE OF CONTENTS

FEATURES 1

PECIFICATIONS 1

INSTALLATION 2

Mounting the Panel ........................................................................................................................................................ 2

Mounting the Keypad ....................................................................................................................................................2

Auxiliary Power Connection ...........................................................................................................................................2

PGM Terminal Connections...........................................................................................................................................2

Keypad Wiring ...............................................................................................................................................................2

Bell/Siren Connection.....................................................................................................................................................2

Fire Zone Wiring.............................................................................................................................................................3

Burglary Zone Wiring ..................................................................................................................................................... 3

AC Power Wiring ............................................................................................................................................................3

Battery Connection ........................................................................................................................................................3

Telephone Line Wiring ...................................................................................................................................................3

GUIDELINES FOR LOCATING SMOKE DETECTORS 4

KEYPAD FUNCTIONS 5

Introduction ....................................................................................................................................................................5

Master Code ..................................................................................................................................................................5

2nd Master Code ...........................................................................................................................................................5

Installer’s Programming Code ....................................................................................................................................... 5

Arming............................................................................................................................................................................5

Auto-bypass/Home-away Arming..................................................................................................................................5

Arming Without Entry Delay...........................................................................................................................................5

Disarming .......................................................................................................................................................................5

Zone Bypassing ............................................. [∗]+[1] .................................................................................................5

Trouble Conditions......................................... [∗]+[2] .................................................................................................6

Alarm Memory................................................ [∗]+[3] .................................................................................................6

Downloading Callup Command..................... [∗]+[4] .................................................................................................6

User Programming Command....................... [∗]+[5]+[Master Code] .......................................................................6

EEPROM Reset ..............................................................................................................................................................7

User Function Commands............................. [∗]+[6]+[Master Code] .......................................................................7

Setting the Clock ......................................... [∗]+[6]+[Master Code]+[1] ................................................................7

Set Auto-Arm Time ...................................... [∗]+[6]+[Master Code]+[2] ................................................................ 7

Quick-Arm ON/OFF ..................................... [∗]+[6]+[Master Code]+[4] ................................................................7

Auto-Arm ON/OFF ....................................... [∗]+[6]+[Master Code]+[5] ................................................................7

Door Chime ON/OFF ................................... [∗]+[6]+[Master Code]+[6] ................................................................7

Bell Test ....................................................... [∗]+[6]+[Master Code]+[8] ................................................................ 8

Installer’s Test ON/OFF.................................. [∗]+[6]+[Master Code]+[0] ................................................................ 8

Utility Output Command ................................ [∗]+[7] or [∗]+[7]+[Access Code].....................................................8

Installer’s Programming Command............... [∗]+[8]+[Installer’s Code] ...................................................................8

Arming without Entry Delay ........................... [∗]+[9]+[Access Code] ...................................................................... 8

Arming For The Night..................................... [∗]+[1] .................................................................................................8

Quick-Exit....................................................... [∗]+[0] when Armed............................................................................8

Quick-Arm Command .................................... [∗]+[0] when Disarmed....................................................................... 8

Keypad Zones................................................................................................................................................................8

PROGRAMMING GUIDE 9

Introduction ....................................................................................................................................................................9

Programming .................................................................................................................................................................9

Program Data Review ....................................................................................................................................................9

Binary Data Display ..................................................................................................................................................... 10

HEX Data Programming...............................................................................................................................................10

36ii

PROGRAMMING SECTIONS 11

[00] Binary Programming ............................................................................................................................................11

[01] 1st Phone Number ............................................................................................................................................... 11

[02] 1st Account Code ................................................................................................................................................ 11

[03] 2nd Phone Number..............................................................................................................................................11

[04] 2nd Account Code...............................................................................................................................................11

Reporting Codes [05] to [10] ......................................................................................................................................11

[05] Zone Alarm Reporting Codes ..............................................................................................................................11

[06] Zone Restoral Reporting Codes ..........................................................................................................................11

[07] Closing (Arming) Reporting Codes / Partial Closing Reporting Code ................................................................12

[08] Opening (Disarming) Reporting Codes / After Alarm Reporting Code ..............................................................12

[09] Priority Alarms and Restorals ..............................................................................................................................12

[10] Maintenance Alarms and Restorals.....................................................................................................................12

[11] Zone Definitions ...................................................................................................................................................12

[12] 1st System Option Code......................................................................................................................................13

[13] 2nd System Option Code ....................................................................................................................................14

[14] 3rd System Option Code .....................................................................................................................................14

[15] Communication Variables ....................................................................................................................................14

[16] Zone Bypass Mask ..............................................................................................................................................14

[17] System Times.......................................................................................................................................................14

[18] Auxiliary Delay Zone Entry / Exit Times ...............................................................................................................15

[19] System Clock Times ............................................................................................................................................15

[20] New Installer’s Code ............................................................................................................................................15

[21] New Master Code ................................................................................................................................................ 15

[22] 2nd Master Code .................................................................................................................................................15

[23] Communication Formats......................................................................................................................................15

[24] Programmable Output Options (PGM Terminal).................................................................................................16

[25] Communicator Call Direction...............................................................................................................................16

[26] Downloading Telephone Number ........................................................................................................................17

[27] Downloading Access Code .................................................................................................................................17

[28] Panel Identification Code.....................................................................................................................................17

[29] For Future Use .....................................................................................................................................................17

[30] Reset to Factory Default ......................................................................................................................................17

[31] 4th System Option Code .....................................................................................................................................17

[32] 5th System Option Code .....................................................................................................................................17

[33] For Future Use .....................................................................................................................................................17

[34] 6th System Option Code .....................................................................................................................................17

[35] LINKS1000 Test Reporting Code ........................................................................................................................18

[36] Keypad Lockout Control ...................................................................................................................................... 18

[90] Installer’s Lockout Enable.................................................................................................................................... 18

[91] Installer’s Lockout Disable ...................................................................................................................................18

FOR THE RECORD 19

PROGRAMMING WORK SHEETS 20 - 28

HOOKUP DIAGRAM 29

LIMITED WARRANTY 30

FEATURES

Keypad Programmable

The PC1500 is complete with a default program so that it is

operational with a minimum of programming. The control

panel is completely programmable from the keypad.

EEPROM Memory

ThepanelusesEEPROMmemorywhichwillretainallprogram

informationevenifACandbattery powerisremoved fromthe

panel. The EEPROM memory can be reprogrammed

thousands of times.

Static/Lightning Protection

The PC1500 has been carefully designed and tested to

providereliableprotectionagainststaticandlightninginduced

transients. Our special “Zap-Trac” circuit board design

catches high voltage transients right at the wiring terminals,

and transient protection devices are placed in all critical

areas to further reduce damaging voltages.

Supervision

• Low or disconnected battery

• Loss of AC power

• Fuse open

• Loss of time on system clock

• Microprocessor “Watchdog” circuit

Operation

• Download / Upload capability

• Programmable auto downloading

• Swinger shutdown

• Transmission delay

• Six access codes

• Master Code

• All zones programmable as fire zones

• Programmable test transmission

• Zone bypass from the keypad

• Six zones

• Bell / Siren zone

• Programmable output

• Three dedicated keys (Fire/Auxiliary/Panic)

• Backlit aesthetically pleasing keypad

SPECIFICATIONS

PC1500 Control Panel

• Six fully programmable zones

- EOL resistor supervised option

- all zones programmable as fire zones.

- maximum zone loop resistance 100 ohms

• Bell / Siren outputs: 1 amp

- steady for burglary

- pulsed for fire

• Programmable output: 300 mA

9 programmable options

• Auxiliary power output: 475 mA

• PC1500RK keypad: 3 maximum

• Battery: 12 VDC, 4 Ah minimum

• Transformer: 16 VAC, 40 VA

• Panel dimensions:

- 10" H × 8" W × 3" D (254 mm × 208 mm × 76 mm)

- Surface mount

• Panel colour: beige

PC1500RK Keypad

• Three keypad activated zones: Fire, Auxiliary, Panic

• Backlit keys

• 5 system lights: Ready, Armed, Memory, Bypass,

Trouble

• 6 zone lights

• Keypad dimensions

- 4.5 H × 4.5 W × 0.93" D (114 mm × 114 mm × 23.6 mm)

- Surface mount

• Keypad colour: mist

INSTALLATION

Mounting the Panel

Select a dry location close to an unswitched AC source and

close to the telephone line connection. Remove the printed

circuit board, the mounting hardware and the keypad from

the cardboard retainer inside the cabinet. Before attaching

the cabinet to the wall, press the four white nylon printed

circuit board mounting studs into the cabinet from the back.

Once the cabinet is mounted to the wall, pull all the cables

into the cabinet and prepare them for connection. Use a

meter to test the wiring for opens, shorts and grounds. Press

thecircuitboardontothewhitenylonmountingstuds.Complete

all wiring to the control panel before applying AC power or

connecting the battery.

Mounting the Keypad

Keypads should be located close to the designated “Entry-

Exit” door(s) and mounted at a height convenient for all

users.

NOTE: Complete all wiring to the control panel before

applying AC power or connecting the battery.

Auxiliary Power Connection

The auxiliary power supply can

beusedtopowerkeypads,motion

detectors and other devices that

require12VDC.SeetheFireZone

Wiring section for the connection

of 4-wire smoke detectors. The

total load for the auxiliary power

output must be calculated for all

devices connected across the

AUX+/- terminals andfordevices

connected between the AUX +

and PGM terminals. The output current cannot exceed 475

mA. Allow 35 mA for eachPC1500RK keypad connected to

the panel.

PGM Terminal

Connections

The PGM terminal is a switched

negative output which can be

controlled by various

programming options (See

Programming Guide Section

[24]). Devices controlled by the

PGM output must be connected

between the PGM terminal, which is (-) and the AUX (+)

terminal.

Keypad Wiring

Up to three keypads may be connected in parallel. Do not

connect multiple keypads on the same keypad wire run. For

Standby Loading purposes, use a current draw of 35 mA per

keypad. This represents the panel in the disarmed state with

two zones open.

The wiring table gives the wire run length from the control

panel to the keypad for various gauges of wire. Wire run

lengths are based on the maximum current drawn by the

keypad. (All lights ON).

If two wires of the same gauge are paralleled, the run length

can be doubled. eg. If 8 #22 AWG wires are used, 2 red, 2

Wiring Chart PC1500RK

Wire Gauge Max. Run Length

(AWG) Keypad to Panel

24 260’ (79m)

22 420’ (127m)

20 660’ (200m)

19 830’ (252m)

18 1050’ (318m)

blk, 2 grn and 2 yel, the run length would go from 420’ to 840’

Bell Loop Wiring Chart

AWG AWG AWG AWG AWG

Current 14 16 18 19 22

mA Distance to last bell or siren (ft./m.)

100 2375/724 1500/457 940/287 750/229 370/113

200 1190/363 750/229 470/143 370/113 185/ 56

300 790/241 500/152 310/ 94 250/ 76 120/ 37

400 595/181 375/114 235/ 72 185/ 56 90/ 27

500 475/145 300/ 91 190/ 58 150/ 46 75/ 23

600 400/122 250/ 76 155/ 47 125/ 38 60/ 18

700 340/104 210/ 64 135/ 41 105/ 32 50/ 15

800 300/ 91 190/ 58 115/ 35 90/ 27 45/ 14

900 265/ 81 170/ 52 100/ 30 80/ 24 40/ 12

1000 240/ 73 150/ 46 90/ 27 75/ 23 35/ 11

(127 to 254 m).

Bell/Siren Connection

Wire run distances are in feet/meters from the control panel

to the last device on the loop. Calculations are based on 12

VDC at the panel with a maximum 10% voltage drop at the

last device. Observe polarity when connecting siren drivers,

sirens and polarized bells.

Fire Zone Wiring

Any one of the 6 zones may be programmed as a Fire Zone.

See Programming Guide Section [11].

Smoke detectors should be the latching type and have N.O.

alarm initiating contacts. Power wiring from the AUX + /

PGM terminals should be supervised using an RM-1 relay

after the last smoke detector. The RM-1 N.O. contacts

(closed with power applied) should be wired in series with

AWG AWG AWG AWG AWG AWG

14 16 18 19 22 24

19 800' 12 450' 7800' 6200' 3000' 1900'

6035m 3794m 2377m 1889m 914m 579m

Figuresbasedonmaximumloopresistanceof100ohms.

Alarm Initiating Loop Wiring Chart

Wire

Gauge

Distance

to EOL

Resistor

Max. Wire Run to E.O.L. Relay

AWG AWG AWG AWG AWG

14 16 18 19 22

4750' 3000' 1880' 1500' 750'

1447m 914m 573m 457m 228m

2375' 1500' 940' 750' 370'

723m 457m 286m 228m 112m

1190' 750' 470' 370' 180'

362m 228m 143m 112m 56m

790' 500' 310' 250' 120'

240m 152m 94m 76m 36m

595' 375' 235' 185' 90'

181m 114m 71m 56m 27m

Current

100

200

300

400

Wire run distances are in feet/meters from the Aux. +/- terminals to

theEnd-Of-Line Power Supervisory Relay. Figures arebased on 12

VDC at the Aux +/- terminals with a maximum 10% voltage drop at

theRM-1relay.

Fire Zone Power Wiring Chart

the alarm initiating end-of-line resistor so that should power

to the detector(s) fail, a fire zone trouble will be initiated.

Burglary Zone Wiring

Burglary zone definition, (eg. Delay, Instant, 24 Hr. etc.) is

Zone Wiring Chart

Figuresbasedonmaximum loop

resistanceof100ohms.

Wire Gauge Max.RunLength to

(AWG) End-of-Lineresistor

24 1900’ (579m)

22 3000’ (914m)

20 4900’ (1493m)

19 6200’ (1889m)

18 7800’ (2377m)

programmed via the keypad. See the Programming Guide,

Section [11].

AC Power Wiring

CompleteallwiringtothecontrolpanelbeforeconnectingAC

power or the battery. Do not plug the transformer into an

outlet that is controlled by a switch.

Battery Connection

Ifthe battery is reverse connected,the 5 A fuse willblow. The

batterychargingvoltageisfactory setandnormallyneedsno

adjustment.Ifthebatterychargingvoltageisoutofadjustment,

contact your service representative.

If AC power is OFF and the battery voltage is approximately

9.5V or lower, thebattery will be disconnectedandthe panel

will power down. To power up again, the AC will have to be

re-established.

Telephone Line Wiring

Do not connect the alarm panel communicator to

telephone lines intended for use with facsimile (fax)

machines. These lines may incorporate a voice filter

which disconnects the line if other than fax signals are

detected. This may result in incomplete transmissions

from the alarm panel communicator.

AUX + PGM Z1 COM

DETECTOR

POWER

12VDC

OUT

N.O.

ALM

OUT

BLK WHT

RED GRN

LATCHING 4-WIRE

SMOKE DETECTOR

1kΩ0.5W

END OF LINE

RESISTOR

RM-1 POWER LOOP

SUPERVISORY RELAY

12VDC 35mA MAX.

WHT

ALARM INITIATING

LOOP; RESISTANCE 100Ω

GUIDELINES FOR LOCATING SMOKE DETECTORS

Experience has shown that all hostile fires in family living

units generate smoke to a greater or lesser extent.

Experiments using typical fires in family living units indicate

that detectable quantities of smoke precede detectable

levels of heat in most cases. For these reasons, smoke

detectors should be installed outside of each sleeping area

and on each additional story of the family unit.

The following information is for general guidance only and it

is recommended that the smoke detector manufacturer's

literature be used for detailed installation instructions.

It is recommended that additional smoke detectors beyond

those required be installed for increased protection. The

added areas include: basement, bedrooms, dining rooms,

furnace room, utility room and hallways not protected by the

required detectors.

FIG. 1: A smoke detector should be located between theFIG. 1: A smoke detector should be located between the

FIG. 1: A smoke detector should be located between the

sleeping area and the rest of the family unit.sleeping area and the rest of the family unit.

sleeping area and the rest of the family unit.

FIG. 2: In the family living units with more than oneFIG. 2: In the family living units with more than one

FIG. 2: In the family living units with more than one

sleeping area, a smoke detector should be located tosleeping area, a smoke detector should be located to

sleeping area, a smoke detector should be located to

protect each sleeping area.protect each sleeping area.

protect each sleeping area.

FIG.3: A smoke detector should belocatedon each storyFIG.3: A smoke detector should belocatedon each story

FIG.3: A smoke detector should belocatedon each story

of the living unit.of the living unit.

of the living unit.

FIG.4: SmokeDetectormounting-“Dead”AirSpace.TheFIG.4: SmokeDetectormounting-“Dead”Air Space. The

FIG.4: SmokeDetectormounting-“Dead”AirSpace.The

smoke from a fire generally rises to the ceiling, spreadssmoke from a fire generally rises to the ceiling, spreads

smoke from a fire generally rises to the ceiling, spreads

out across the ceiling surface and begins to bank downout across the ceiling surface and begins to bank down

out across the ceiling surface and begins to bank down

from the ceiling. The corner where the ceiling and wallfrom the ceiling. The corner where the ceiling and wall

from the ceiling. The corner where the ceiling and wall

meet is an air space into which the smoke may havemeet is an air space into which the smoke may have

meet is an air space into which the smoke may have

difficulty penetrating. In most fires, this “dead”air spacedifficulty penetrating. In most fires, this “dead”air space

difficulty penetrating. In most fires, this “dead”air space

measures about 4 in. (0.1m) along the ceiling from themeasures about 4 in. (0.1m) along the ceiling from the

measures about 4 in. (0.1m) along the ceiling from the

corner and about 4 in. (0.1m) down the wall as shown incorner and about 4 in. (0.1m) down the wall as shown in

corner and about 4 in. (0.1m) down the wall as shown in

Figure 4. Detectors should not be placed in the dead”airFigure 4. Detectors should not be placed in the dead”air

Figure 4. Detectors should not be placed in the dead”air

space.space.

space.

NEVER

HERE

Acceptable

here

Top of detector

acceptable here

12"

(0.3m)

Max.

(0.1m)

Max.

(0.1m)

Ceiling

Wall

NOTE: Measurements shown are to

the closest edge of the detector.

Bedroom Bedroom

Basement

Living

Room Dining

Room

Bedroom Bedroom

Bedroom

Living RoomKitchen

Family Room

Bedroom

Living

Room

Dining

Room

Kitchen

Bedroom

KEYPADFUNCTIONS

Introduction

The PC1500RK remote keypad provides complete

information and control of the PC1500 control panel. The

panelcanbefullyprogrammed fromthekeypad.The6 zone

lights provide alarm and status indication for the alarm

circuits. Each zone can be programmed to be a burglary

zone or a fire zone. The five function lights guide the user

inoperatingthesystem andthebuilt-insounder letstheuser

hear correct key entries and other alert signals. The 12 digit

keypad is used for code entry and other programming

functions. The single button [F]ire, [A]uxiliary and [P]anic

keys provide the user with simple operation for emergency

signalling. All keypad entries are made by pressing one key

at a time.

Master Code

A default Master Code “1234”is factory programmed into

thePC1500. TheMaster Codeis usedto armand disarmthe

panel, to reset the bells after an alarm, to program up to 11

additional codes using the [∗][5] command, and to enter

other user functions using the [∗][6] command. The panel

defaultprogram allowstheuser tochangethe MasterCode.

The panel can be programmed, by the installer, so the user

cannot change the Master Code. See 2nd System Option

Code light 2.

2nd Master Code

AsecondMasterCodecanbeprogrammedintothePC1500.

This code can be changed by the installer only, and is useful

wheretherearemultiplepanelsinacomplex.The2ndMaster

Code may be used as a “Master Key”. The default 2nd

Master Code is blank.

Installer’s Programming Code

AdefaultInstaller’sProgrammingCode“1500”isprogrammed

into the PC1500. Using this code and the [∗][8] command,

the installer can gain access to the system to enter panel

program information. This code can be changed by the

installer.

Arming

Before arming the panel, close all protected doors and

windows and stop movement in areas covered by motion

detectors. If the “Trouble”light is on, check for the type of

trouble ([∗][2] command) and correct the fault condition. If

the “Bypass”light is on, insure that the zones bypassed are

bypassed intentionally, ([∗][1] command). If the “Ready”

light is not on, one or more zones are open. The system can

only be armed when the “Ready”light is ON. To arm, enter

a 4 digit access code. As each digit is entered, the keypad

sounder will beep. When the correct access code has been

entered the “Armed”light will come ON and the keypad will

beep 6 times. If the access code has been entered

incorrectly, the keypad will sound one long tone. Press the

[#] key and enter the access code again.

When the correct access code has been entered and the

“Armed”light is ON, exit through the designated entry/exit

door before the Exit Delay time expires. At the end of the

allowed exit time, all lights on the keypad will go out except

the “Armed”light. The “Bypass”light will be ON if a zone is

bypassed and if Show Bypassed Status While Armed is

programmed in Section [31], zone light 4 ON.

See Installer’s programming Section [∗][8] command for

instructions on changing the Exit Delay time.

Auto-bypass/Home-away Arming

If a correct access code is entered, and you do not

exit the

premises, the system will, at the end of the Exit Delay time,

arm with interior zones automatically bypassed if those

interior zones have been programmed as “Home-away”

zones. The “Bypass”light will come ON. (See programming

Section [11], Zone Definitions for programming zones as

“Home-away”).

This is a convenience feature for the user who wishes to

remain at home with the system armed. The user does not

have to manually bypass the interior zones.

To reactivate the interior zones that have been automatically

bypassed, press [∗][1]. The “Bypass”light will go out. If the

bypassed zones were programmed as Home-away with

delay, the “Bypass”light will go out after the delay. This

commandisaquickmethodoffullyarmingthesystembefore

going to bed and is useful for the user who has a keypad

outside the areas protected by the interior zones.

Arming Without Entry Delay

To eliminate the Entry Delay, arm the system using [∗][9],

[any valid access code]. An exit may be made as in normal

arming. The system will arm as described above in Auto-

bypass / Home-away arming whether an exit is made or not.

The “Armed”light will flash to indicate that the system is

armed without the Entry Delay.

Disarming

Enter the premises through the designated entry-exit door.

The keypad sounder will be on as a reminder to disarm the

system. Go to the keypad and enter a valid access code. If

an error is made entering the code, press the [#] key and

enter the code again. The “Armed”light will go out and the

sounder will stop. The correct access code must be entered

before the entry time expires or the panel will go into alarm.

TochangetheentrytimeseeInstaller’sProgrammingSection

[17].

If an alarm occurred while the panel was armed, upon

disarming the “Memory”light and the zone light(s) of the

zone(s) that caused the alarm will flash for two minutes.

Pressing the [#] key will stop the flashing, extinguish the

zone light(s) and return the panel to the ready mode. The

“Memory”light will stay on steady to indicate that an alarm

did occur during the last armed period. To view the zone(s)

that caused the alarm, see Alarm Memory Display [∗][3].

Zone Bypassing

[∗∗

∗∗

∗]+[1]

A bypassed zone will not cause an alarm. Use zone

bypassingwhenaccessisneededtopartofaprotectedarea

or if damage to contacts or wiring cannot be repaired

immediately. The panel can be armed with one or more

zones bypassed even if the zone(s) are open. The “Ready”

light will be ON and the “Bypass”light will be ON if a zone is

bypassed. A fire zone cannot

be bypassed.

If the “Bypass”light is ON when arming, use the [∗][1]

commandtodisplaythebypassedzonesandensurethatany

zonedisplayedasbeingbypassedisintentionallybypassed.

Zone bypasses are automatically cancelled when the panel

is disarmed.

ToBypassZones:

Enter [∗][1] - the “Bypass”light will start flashing.

Enter[zonenumbertobebypassed];the zonelightwill come

ON to indicate that the zone is bypassed. To remove a

bypass,enterthezonenumberandthezonelightwillgoOFF.

Continue entering the zone numbers for the zones you want

bypassed. Press [#] to return to Ready.

To Recall Bypassed Zones:

Enter [∗][1][9]

This command will recall the last zone or group of zones that

were bypassed. If the same group of zones are bypassed

regularly, the bypass recall feature can be used instead of

bypassing the zones individually.

Bypass Disable:

The PC1500 can be programmed by the installer to prevent

certain zones from being bypassed by the user. Lights for

these zones will not come ON in response to the bypass

command. See the Zone Bypass Mask instruction in the

installer programming Section [16].

Trouble Conditions

[∗∗

∗∗

∗]+[2]

The PC1500 continuously monitors a number of trouble

conditions. If one of these conditions occurs, the keypad

“Trouble”light will come ON and the buzzer will sound two

short beeps every 10 seconds. To silence the buzzer, press

the [#] key. The buzzer will stop but the “Trouble”light will

remain ON until the trouble condition is cleared. See the

Programming Guide Section [10], Maintenance Alarms &

Restoralsforalistoftroubleconditionsthatcanbetransmitted

to the monitoring station.

To view the trouble condition, press [∗][2].

1. Low Battery. If the battery voltage is low, the battery is

disconnected or the battery fuse is blown, a trouble will be

displayed and can be reported.

2. AC Failure. On loss of AC power, the “Trouble”light will

comeON immediately, but the keypad buzzerwillnot sound.

ThekeypadbuzzerwillsoundifACpowerremainsoffandthe

battery reaches a low voltage. The delay before transmitting

AC Fail can be programmed from 1 to 99 minutes. See

Programming Section [17].

3. Fuse Failure - Bell / Siren or AUX Output. A trouble is

displayed if the Bell / Siren fuse is open. If the AUX output

fuse fails, it will not be displayed but will be transmitted if

programmed to do so.

4. Unsuccessful Communication Attempt If the digital

communicator is unsuccessful at communicating with the

monitoring station after 8 attempts at each phone number

that is tried, a trouble is generated. See Section [25],

CommunicationVariables. Ifalaterattemptatcommunication

is successful, the trouble is cleared. The trouble can also be

cleared by pressing the [#] key to exit from the trouble view

mode.

5. Fire Alarm Circuit Trouble An open circuit on the zone

programmed as a Fire Zone will initiate a trouble. See Zone

Definitions Section [11] for Fire Zone assignment.

6. Loss of Time on System Clock

...

When the PC1500 is

powered up or reset, the internal time of day clock needs to

be reset to the correct time. The trouble is cleared after

entering the trouble view mode then pressing [#] to exit. The

trouble will also be cleared on any attempt to set the time of

day. See [∗][6] User Function Command for setting the

clock. Press [#] to return to Ready. NOTE: A trouble will not

be generated if both the test transmission and Auto-Arm

times are not programmed with valid times.

NOTE:

If[9]ispressedwhile inthetroubledisplaymode,the

most recent trouble will be displayed on the zone lights. This

trouble memory is most useful as a diagnostic tool when

installing and servicing the PC1500.

Alarm Memory

[∗∗

∗∗

∗]+[3]

Alarms caused during the previous armed period are stored

in memory. To view these alarms, press [∗] then [3]. The

“Memory”lightwill flashand thealarm(s) willbe displayedon

the flashing zone lights.

In addition to the last alarm memory, there are two history

levels. Afterenteringthememorymode,pressingany key[0]

to [9] will display the two other levels of alarm history. Each

time a key is pressed, the keypad will beep 1, 2 or 3 times to

indicate which level of history is being viewed.

When the panel is armed, and if there is an alarm in the 1st

level, the 1st level is cleared and the contents moved to the

2nd level. The 2nd level contents are moved to the 3rd level

andthe3rdlevelcontentsarediscarded. The “Memory”light

will be ON only if there was an alarm during the previous

armed period. Press [#] to return to Ready.

Downloading Callup Command

[∗∗

∗∗

∗]+[4]

The [∗][4] command is used to initiate a call to the

downloadingcomputersothatthepanelcanbeaccessedby

the computer. This command must be enabled in Section

[14],3rdsystemoptioncode,zonelight2. Sections[26],[27]

and [28] must be programmed with the downloading

computer’s telephone number, the downloading access

code and the panel identification code. NOTE: The [∗][4]

command can be programmed to require a access code

(e.g. [∗][4][4-digit access code]) if Section [14] light 4 is

turned ON.

User Programming Command

[∗∗

∗∗

∗]+[5]+[Master Code]

The[∗][5]programmingcommandallowstheusertoprogram

accesscodes2through 6.The1staccess codeistheMaster

Code, which the installer may choose not to allow the user to

program (Section [13] light 2). The factory default for the

Master Code is “1234”. The 6th code may be changed from

a regular code into a “one-time”use or “Maid’s Code”. See

Section [13] light 5.

NOTE:

TheOne-timeUsecodeisonlyclearedwhenitisused

to arm. If the Quick-Arm command [∗][0] is used to arm, the

“one-time”code will not be erased.

Programming Access Codes

Enter [∗][5][Master Code] to enter the access code

programmingmode. The“Memory”, “Bypass”and“Trouble”

lights will begin to flash. The zone lights are used to indicate

the program status of the 6 access codes.

Zone Light Access Code Status

OFF Code not programmed

ON steady Code programmed

Flashing Code being programmed

Upon entering this programming mode, the 1st zone light

will be ON to indicate that the Master Code is programmed

with the Factory Default Code. The Master Code may be

changed here or in Section [21] if the installer chooses to

disable user-changing of the Master Code.

Changing or Adding a Code

To change access codes 1 to 6, press the corresponding

key(1 to 6). The corresponding zone light will begintoflash.

Enter the new four digit number. Do not use the [∗] key or

[#] key when entering the four digit number. After the four

digitsareentered,thekeypadwillbeep3timesandthezone

light will come on steady. If you are changing an existing

code, the new code will simply replace the old one. If you

wish to program another code, press the number key for the

code to be programmed and enter the new 4-digit code.

Press the [#] key to exit this section.

Erasing a Code

To erase a code, enter [∗][5][Master Code]. Press the key

of the code you wish to erase. The zone light for that code

number will flash. Enter [∗∗∗∗].

NOTE:

The Master Code cannot be erased. If the Master

Code is forgotten and the panel is left disarmed, program a

new Master Code using the [∗][8][Installer’s Code][21]

command or use the 2nd Master Code to reprogram the

Master Code.

EEPROM Reset

If the Master Code is forgotten and the panel is armed, see

ProgrammingSection[30]forsoftwareandhardwaremethods

of resetting the panel to the factory default condition. Reset

is not necessary if the 2nd Master Code is programmed.

User Function Commands

[∗∗

∗∗

∗]+[6]+[Master Code]

This function is used to set the System Clock time and to set

the Auto-Arm time as well as toggle a number of system

functions.As soon as the command isentered,the “Memory,

“Bypass”and “Trouble ”lights begin to flash.

Enter [∗][6][Master Code][Number from list below].

[1] System 24 Hr. Clock (Enter HH:MM)

[2] Auto-Arming Time (Enter HH:MM)

[3] [Reserved for future use]

[4] Quick-Arm Enable/Disable

[5] Auto-Arm Enable/Disable

[6] Door Chime Enable/Disable

[8] Bell Test Function

[9] [Reserved for future use]

[0] Installer’s Test (turn off after use)

(This function will turn off automatically on arming.)

Items [4], [5], [6] and [0] turn ON and OFF various features.

When the item key is pressed and the feature is being turned

ON, the keypad sounder will beep 3 times. If the feature is

being turned OFF the sounder will give one long beep.

Pressing item [8] gives a 2-second Bell / Siren and Keypad

Light and Buzzer test.

Setting the Clock

[∗∗

∗∗

∗]+[6]+[Master Code]+[1]

The System Clock is a 24-hour clock and times must be

entered as 2-digit numbers.

e.g. HH - 01, 02, .... 10, 11, .... 23, 00

MM - 01, 02, .... 35, 36, .... 58, 59

8:05 AM would be entered as 0805

1:30 PM would be entered as 1330

Setting the system 24 Hr. clock tells the system the time of

day. If the system is without power, (AC and battery), it

cannot continue to keep time. When the panel is powered

up, the system clock must be reset. If the time needs to be

reset,thenatrouble#6 willbeindicatedonthekeypad.(See

[∗][2] System Trouble Display). Trouble #6 will not be

generated if the Auto-Arm time is not programmed with a

valid time (9999 in these positions disables these features;

refer to Section [19]).

Set Auto-Arm Time

[∗∗

∗∗

∗]+[6]+[Master Code]+[2]

The PC1500 can be programmed to arm at the same time

each day. At the selected Auto-Arm time, the bell will sound

one short burst every 10 seconds for a one minute period if

Section [32] light 2 is off. The keypad will also sound for one

minute. If any key is pressed during the 1 minute warning

period, Auto-Arming will be aborted. Auto-Arming will be

attempted at the same time the next day. To set the Auto-

Armtime, enter [∗][6][MasterCode][2] then enter the hours

and minutes as described at the beginning of this section.

This feature must also be enabled (see item [5] below).

Quick-Arm

ON/OFF [∗∗

∗∗

∗]+[6]+[Master Code]+[4]

Pressing [4] while in the User Function Command mode will

Enable (3 beeps) or Disable (one long beep) the Quick-Arm

feature.Withthisfeatureenabled,thepanelcanbe armedby

simply entering [∗][0].

Auto-Arm

ON/OFF [∗∗

∗∗

∗]+[6]+[Master Code]+[5]

Pressing [5] while in the User Function Command mode will

enable (3 beeps) or disable (one long beep) the Auto-Arm

feature.Withthisfeatureenabled,thepanelwillautomatically

armat the sametime each day. Thetime is setinSection [19]

or [∗][6][Master Code][2].

Door Chime

ON/OFF[∗∗

∗∗

∗]+[6]+[MasterCode]+[6]

Pressing [6] while in the User Function Command mode will

enable (3 beeps) or disable (one long beep) the Chime

feature. With this feature enabled, the keypad will beep 5

times when any zone defined as a delay or instant circuit

opens or closes. The Door Chime feature does not operate

on other zone definitions. Zone Bypass may be used to

eliminatebeeping onzones whereit isnot wanted.The Door

Chime feature functions only while the panel is in the

Disarmed mode.

Bell Test

[∗∗

∗∗

∗]+[6]+[Master Code]+[8]

Pressing [8] while in the User Function Command mode will

sound the bell/siren, the keypad sounder and turn on all the

keypad lights for 2 seconds.

Installer’s Test

ON/OFF [∗∗

∗∗

∗]+[6]+[Master Code]+[0]

Pressing the [0] key while in the User Function Command

mode will enable/disable the Installer’s Test function. This

feature facilitates final testing of the system and when

enabled, the bell/siren will operate for 2 seconds each time

a zone is put into alarm. Each zone should be tripped

individually to avoid confusion about which zone originates

the alarm. To exit the Installer’s Test mode, arm then disarm

the panel.

NOTE:

The communicator will transmit all alarms and

restorals. Disable the communicator if this is not desired

(Section [12], light 1).

Utility Output Command

[∗∗

∗∗

∗]+[7] or [∗∗

∗∗

∗]+[7]+[Access Code]

The Programmable Output (PGM terminal) can be

programmed for activation by a keypad command. This

output can be used to operate other devices such as door

openers, special lighting, door strikes or to reset smoke

detectors. (See Programming Section [24], item 2, 3 or 4).

Depending on the option chosen, the [∗][7] command may

or may not require a subsequent access code.

When the correct command is entered, the keypad sounder

and the PGM output will operate for 5 seconds.

Installer’s Programming Command

[∗∗

∗∗

∗]+[8]+[Installer’s Code]

The PC1500 is completely programmed from the keypad by

using commands inthe [∗][8]section.Thesecommandsare

describedindetailintheprogrammingsectionofthismanual.

The default Installer’s Code is [1500].

Arming without Entry Delay

[∗∗

∗∗

∗]+[9]+[Access Code]

Entering [∗][9] before the arming code will arm the panel

without the Entry Delay on delay zones. Also “Home-away”

zones are automatically bypassed. When armed using the

[∗][9] command, the “Armed”light will flash to remind the

user that the system is armed without the Entry Delay. This

command allows the user to remain at home and have an

instant alarm on the entry doors.

Arming For The Night

[∗∗

∗∗

∗]+[1]

To reactivate “Home-Away”zones that have been bypassed

by arming with the [∗][9] command, enter [∗][1]. When this

command is entered, the “Armed”light will continue to flash

to remind the user that the Entry Delay is not applied to the

Delay Zones. Also, the “Bypass”light will be shut OFF to

indicate that the Home-Away zones are no longer bypassed.

Notethatthe [∗][1]commandwill notremovebypasses from

zones that have been manually bypassed.

Quick-Exit

[∗∗

∗∗

∗]+[0] when Armed

Entering [∗][0] when the system is armed will allow the user

to exit the premises through any delay zone without altering

the status of the system if the Quick-Exit feature is enabled.

The Quick-Exit feature can be enabled by turning on option

4 in programming Section [32]. For 2 minutes after [∗][0] is

entered into an armed system, one and only one delay zone

may be tripped. Any additional activity on any other active

zone will cause that zone to begin its alarm sequence.

Quick-Arm Command

[∗∗

∗∗

∗]+[0] when Disarmed

Entering [∗][0] is accepted as a valid arming code if the

Quick-Arm feature is enabled. This command is often used

when individuals are required to arm the system but not

disarm the system. This could be used with home visitors in

thecase ofa residentialalarm systemor forjunior employees

and maintenance staff in the case of commercial systems.

See [∗][6] User Functions Command section, for enabling

and disabling the Quick-Arm feature.

Keypad Zones

[F] - [A] - [P]

Thereare three zones which can be activated withsingle key

entries on the keypad. For the [F], [A] and [P] keys to be

functional for transmission, they must be enabled by the

installer by entering the Alarm and Restoral Codes in

Programming Section [09].

[F]ire Key Pressing the [F] key and holding it for 1 second

will initiate a local pulsing alarm and, if programmed, will

transmit the alarm to the monitoring station. The keypad will

sound a series of short beeps once the panel has accepted

the alarm.

[A]uxiliary Key Pressing the [A] key and holding it for 1

secondwill, ifprogrammed, transmit anAuxiliary alarm tothe

monitoring station. There is no local alarm and no keypad

lights will come ON when this key function is activated. The

keypad will sound a series of short beeps upon successful

completion of the transmission to the monitoring station.

[P]anic Key Pressing the [P] key and holding it for 1 second

will, if programmed, send a transmission to the monitoring

station. The alarm signal can be programmed to be

audible

silent.

See Programming Section [12], 1st System Option

Code,Light6. Ifprogrammedas

audible,

thelocalbell/siren

will sound steadily.

Keypadaudibleannunciationforthe[P]keyisprogrammable,

Section [14], Light 5, for feedback (3 beeps) or silent (no

buzzerfeedback). Ifprogrammedfor

audible,

thebuzzerwill

sound once the key input is accepted.

PROGRAMMINGGUIDE

Introduction

ThePC1500isfullyprogrammablefromthekeypadanduses

anEEPROMmemorywhichcanbereprogrammedthousands

oftimes.TheEEPROMmemorywillnot losetheprogramdata

even on total loss of power. The essential information which

defines the operation of the control panel is stored in a

section of the EEPROM memory which is accessible using

the Installer’s Programming code or via downloading. If the

Installer’scode is forgotten, the EEPROM may be reset to the

factory default code. See Section [30], Reset to Factory

Default.

Programming

With the panel in the disarmed mode, enter [∗][8][1500].

Thepanelcanonlybeprogrammedwhileitisinthedisarmed

mode. The default installer’s code is 1500; the installer’s

code can be changed. See Section [20], New Installer’s

Code.

Once the installer’s command is entered, the “Armed”light

will come ON steadily and the “Memory“, “Bypass”and

“Trouble”lights will flash. This indicates that the panel is

ready for programming. NOTE: If no key entry is made for

2 minutes, the panel will return to the Ready mode and the

complete installer’s command will have to be entered before

programming can be resumed.

With the “Armed”light ON steadily, enter 2 digits for the

section you wish to program. The sections for the PC1500

panel range from [01] to [36], and each section can be

programmed independently. Section [00] is reserved for

binary programming which is normally done on instruction

from factory technical personnel.

Once the 2 digits for the section you wish to program are

entered, the “Armed”light will go OFF, the “Ready”light will

go ON steadily, and the keypad sounder will beep 3 times.

The keypad is now ready to accept data for the selected

section.

Most sections contain groups of 2-digit entries and the

keypad buzzer will beep twice after each 2-digit group is

entered.

When the section is first entered, the first 4 zone lights will

indicate, in a binary format, the value of the first digit in that

section (refer to “Binary Data Display”on the next page). If

you wish to change that digit, simply enter the new digit from

thekeypad. Ifyouwishtokeepthatdigitunchanged,youcan

enterthesamenumberorskipthedigitbypressingthe[F]key.

Once the first digit has been entered or skipped, the 4 zone

lightswilldisplaythevalueoftheseconddigit. Aftereachdigit

isenteredorskipped,thezonelightsshowthevalueofthenext

digit in the binary format.

When the required data for the section being programmed is

completely entered, the keypad sounder will beep several

times and the “Armed”light will come ON to indicate that the

expected data has been entered.

At this point, you will still be in the program mode and need

only enter the section number for the next section you wish

to program.

It is not necessary to program all 2-digit pairs in any given

section. Asectioncanbeenteredandselectivelyprogrammed

by going only to the digit(s) you wish to change and then

pressing [#] to return to the programming mode where you

canthenenteranothersection numberforprogramming. For

2-digitpairs,bothdigitsmustbeprogrammedbeforepressing

the[#]key. Only thedataentered beforepressingthe [#]key

will be changed in the EEPROM.

Program Data Review

•Enter the section you wish to program by entering the 2-

digit section number.

•The first 4 zone LEDs will represent the value, in binary

format, of the first digit in that section.

•Each press of the [F] key will advance the display to the

next digit.

•At the end of the section, the keypad will beep several

times and then return to the program mode so that

another section can be selected for review or

programming.

NOTE:OnlySections[01]through[11],[15],and[17]through

[28] can be reviewed using the method described above.

Sections[12],[13],[14],[16],[31],[32],[34]

Thesesectionsusethezonelightstoindicatewhichfunctions

areactiveandwhichnumberkeytopresstoturnthemONand

OFF. When one of these sections is entered, zone lights 1 to

6 will display which functions are currently ON. Pressing the

key number corresponding to the zone light number will

alternately turn the function ON and OFF, and the zone light

will correspond to this. All functions can be turned OFF at

oncebypressing[0]. Whenthecorrectselectionshavebeen

made, press [#] to save the selections in memory and return

totheprogrammodewhere anothersectioncanbeselected.

Binary Data Display

Zonelights1through4areusedtodisplaythevalue,inbinary

format, of the data as shown in the table below.

Hex Data Entry*

Value

Zone 1

Zone 2

Zone 3

Zone 4

Light On

Light Off

* See Hex Data Entry instructions

HEX Data Programming

Certain programming entries may require the entry of data in

HEX(hexadecimal, or base 16) format. HEX numbering uses

the digits 0 through 9 and the letters A through F.

The letters A through F are represented by the number keys

1through6. ToenterdatainHEXformat,firstpressthe[∗]key.

The “Ready”light will flash. Enter the HEX value, then press

the [∗] key again to return to the normal entry mode. The

“Ready”light will stop flashing.

To enter HEX numbers:

A➤Enter [∗][1][∗]

B➤Enter [∗][2][∗]

C➤Enter [∗][3][∗]

D➤Enter [∗][4][∗]

E➤Enter [∗][5][∗]

F➤Enter [∗][6][∗]

Enter [∗] before

and after

each digit. The last digit in each

section does not require the final asterisk ([∗]) to be entered.

PROGRAMMINGSECTIONS

[00] Binary Programming

This section is normally used upon instruction from factory

technicalpersonnelforspecializedprogrammingnotcovered

by the standard programming instructions.

[01] 1st Phone Number

This is the first telephone number the Communicator will dial.

See Section [25], Communicator Call Direction.

After entering Section [01] for programming, enter the

telephonenumber thesame way youwould dialit on atouch-

tone phone. Press [#] after the last digit to complete the

telephone number programming.

A second dial tone search, as required in a PBX system, can

beaddedbyprogrammingaHEX‘D’betweenthedigitsinthe

phonenumber where it is required. Toentera HEX ‘D’, press

[∗] then [4] then [∗].

Instead of a dial tone search, a pause of 4 seconds can be

inserted between digits in a telephone number.

Enter [∗, 2, ∗] to dial a ‘∗’(HEX ‘B’)

Enter [∗, 3, ∗] for a 4-second pause (HEX ‘C’)

The total number of digits, including dial tone searches and

pauses, must not exceed 16. Remember, press [#] to

complete entry of the telephone number.

When complete, enter two digits to program another section.

[02] 1st Account Code

The 1st Account Code is always transmitted to the 1st

telephone number to identify the customer. Enter a 4-digit

number. If the HEX digits ‘A’to ‘F’are required, remember

to enter [∗] before and after the digit entry.

Where a zero is required in the account code, enter HEX ‘A’

(∗, 1, ∗) to transmit 10 pulses which will be interpreted as a

zero by the monitoring station receiver.

If a 3-digit code is required, as in 3/1 formats, enter [0] as the

LASTdigit. The[0]representsanulldigitwherenopulsesare

transmitted.

[03] 2nd Phone Number

This is the second telephone number to which the

communicatorwilldial. See[01]forprogramminginstructions.

[04] 2nd Account Code

The second account code is always transmitted to the 2nd

telephone number. See [02] for programming instructions.

Reporting Codes [05] to [10]

These sections are used to program the communicator

reporting codes. A reporting code is transmitted along with

the account code with each transmission. If the reporting

codes are not programmed, no transmission will be sent

when an event takes place (i.e. alarm, restoral, opening /

closing,trouble, etc.). Toprevent atransmission frombeing

sent for any event in the following sections, leave it

unprogrammed or enter [00] as the reporting code.

Section[05] and [06] each have 6 reporting codes. Sections

[07], [08] and [10] each have 7 reporting codes, while

Section [09] has 8 reporting codes. Once a section is

entered,thesystemexpectsaseries of2-digitnumbers tobe

entered. The keypad beeps twice and the “Armed”light

flashes after each 2-digit entry. After the last 2-digit number

is entered, programming of the current section is complete.

The keypad gives a series of beeps, the “Ready”light goes

OFF and the “Armed”light comes ON. The keypad is then

ready to accept the next 2-digit section number for

programming.

When changing reporting codes in a section, you can scroll

tothecodeyouwishtochangebypressingthe[F]key. Only

codes actually changed will be altered in the EEPROM.

Press [#] to exit from the programming sequence.

[05] Zone Alarm Reporting Codes

Once Section [05] is entered, the panel expects 6 2-digit

numbers for the Alarm Reporting Codes for zones 1 to 6.

These codes are used by the communicator when there has

been an alarm on zones 1 to 6.

Listed below are several programming examples and the

resultingtransmissionusingdifferentformatsforthereporting

codes. Obtaining different formats requires entering data in

the Account Code Section [02] or [04], the Reporting Code

Sections [05] to [10], and the Communicator Format Section

[23].

3/1 FORMAT - Non-extended reporting

Requires:

•3-digit account code in sections [02] or [04].

i.e. Enter 1230 for account code 123

•Format Code [0], [1], [2], [3], [4] depending on

receiver type in Section [23].

•SinglelinedigitAlarmReportingCodeSection[05]

i.e. Enter[30] for single digitcode3 (0=nopulses)

TRANSMISSION SENT: 123 3

4/2 FORMAT - Non-extended reporting

Requires:

•4-digit account code in sections [02] or [04].

i.e. Enter 1234 for account code 1234

•Format Code [0], [1], [2], [3], [4] depending on

receiver type in Section [23].

•2-digit Alarm Reporting Code in Section [05]

i.e. Enter [31] for 2-digit code 31

TRANSMISSION SENT: 1234 31

3/1FORMAT-Extendedreporting

Requires:

•3-digit Account Code in Section [02] or [04]

i.e. Enter 1230 for code 123

•Format Code [8], [9], [A], [B], [C] depending on

receiver type in Section [23]

•2-digit Alarm Reporting Code in Section [05]

i.e. Enter [31] for 2-digit code 31

TRANSMISSION SENT: 1st ROUND 123 3

2nd ROUND 333 1

Ifatransmissionisnotwantedfor aparticularreporting code,

then enter ‘00’or ‘FF’to disable that reporting code.

[06] Zone Restoral Reporting Codes

These reporting codes are used by the communicator to

transmitzonerestoralsforzones1through6. Useinstructions

in Section [05] above as a guide for programming.

[07] Closing (Arming) Reporting Codes

Partial Closing Reporting Code

Reportingcodes1to6areusedtoidentifyclosingsforaccess

codes1to6. IfpartialclosingisidentifiedinSection[14],then

alarmcodesformanuallybypassedzoneswillbetransmitted

whenthesystemisclosedwith oneormore zonesbypassed.

When transmitting in 4/2, 3/1 or any other of the extended

formats, see Section [05] above. The 6 closing codes are

programmed as follows:

[C1], [C2], [C3], [C4], [C5], [C6]

Where the first digit HEX ‘C’represents a closing signal and

the second digit represents the user access code which was

used to arm the system (HEX ’C’could be any other number

depending on what is used at the monitoring station).

The closing code transmission takes place after the Exit

Delay time. Therefore, if the system is armed and disarmed

beforetheexpiryofthe exittime,noclosingtransmissionwill

take place.

The partial closing code, if used, is transmitted in tandem

with the regular closing code to identify the closing as a

partial closing.

When the system has been armed using the Quick-Arm

command [∗][0] or using the Auto-Arm feature, access

code #1 will be transmitted.

[08] Opening (Disarming) Reporting

Codes After Alarm Reporting Code

The first 6 reporting codes correspond to the 6 user access

codes. Whenthesystemisdisarmedusingoneoftheaccess

codes, the corresponding reporting code in this section is

transmitted. SeeSection[07]aboveforexamplesofreporting

code programming.

If the After Alarm Code is programmed, that code will be

transmitted to the monitoring station on opening if an alarm

occurred during previous armed period. This feature is

useful for installations where openings and closings are not

reported normally, but it is desired to have a report to the

monitoringstationonopeningifanalarmdidoccurduringthe

previous armed period. This feature allows the monitoring

stationtoknowwhentheuserisonthepremisesandavailable

toreceiveareportaboutalarmswhilethesystemwasclosed.

[09] Priority Alarms and Restorals

These reporting codes are used by the communicator to

transmit the following list of troubles, alarms and restorals.

See Section [05] as a guide for programming.

•Fire Zone Trouble.

•Keypad [P]anic Alarm.

•Keypad [F]ire Alarm.

•Keypad [A]uxiliary Alarm.

•Fire Zone trouble Restore.

•Keypad [P]anic Restore.

•Keypad [F]ire Restore.

•Keypad [A]uxiliary Restore.

Transmissionforoperationofthe[F],[A]and[P]keyswillonly

takeplaceiftheappropriatesectionsin[09]areprogrammed

with a reporting code.

[10] Maintenance Alarms and Restorals

These reporting codes are used by the communicator to

transmitthefollowinglistofalarmsandrestorals. SeeSection

[05] as a guide to programming.

•Low Battery Alarm.

•AC Failure Alarm.

•Fuse Failure Alarm.

•Low Battery Rrestore.

•AC Failure Restore.

•Fuse Failure Restore.

•Automatic Test Code

The Test Code is not transmitted if periodic downloading is

selected, Section [14], light 3. For Automatic Test Code

Reporting, the time between reports (in days) must be

enteredin Section[17] andthe timeof dayfor thereport must

be entered in Section [19].

[11] Zone Definitions

As in the reporting codes sections, once this section is

entered, 6 2-digit numbers are required. Each 2-digit

number entered defines how a zone will operate.

Zone Definitions Digit #1

The first digit determines whether the zone will cause a silent

alarmoranaudiblealarmandwhether thezoneresponsewill

be fast or slow. Zone response time can be programmed in

Section[17]andcanbesetfrom10msto990ms Thefactory

default zone response time is 500 ms. If set at fast, the zone

response time is 10 ms, and if set at slow, the zone response

time is 500 ms or whatever time is set in Section [17].

[0] = slow & audible

[1] = slow & silent

[2] = fast & audible

[3] = fast & silent

Zone Definitions Digit #2

Digit #2 determines the zone type, [0] through [8], as

described below.

[0] Standard Delay Zone has an Entry and Exit Delay and

is normally used for entry/exit doors. The Exit Delay starts

as soon as the panel is armed. The zone may be opened

and closed during the delay time without causing an

alarm. After the Exit Delay time has expired, opening the

zone will start the Entry Delay timer. During the Entry

Delay time, the keypad buzzer will sound steadily to

advisetheuserthat thesystemshouldbedisarmed.Ifthe

panel is disarmed before the entry time expires, no alarm

will be generated.

The default times for this type of zone are a 30 second

Entry Delay and a 120 second Exit Delay. The Entry and

ExitDelaysmaybeindependentlyprogrammedinSection

[17] for periods from 1 second to 255 seconds. All zones

programmed as type [0] will have the Entry and Exit

Delays as programmed in Section [17] or the default

times if Section [17] is not programmed.

[1] Instant Zone is normally used for door and window

contacts and has the standard Exit Delay but is instant

when opened after the Exit Delay expires. The Exit Delay

will be the default time of 120 seconds or the time as

established in programming Section [17].

[2] InteriorZone isnormallyusedwithinteriormotiondetectors

and has the standard Exit Delay time. The zone also has

the standard Entry Delay time provided that a delay zone

hasbeentrippedfirst.Ifthepremisesareenteredwithout

coming through a “delay”entrance, and a type [2] zone

is tripped, an immediate alarm will be generated.

[3] InteriorHome-awayZone operatesthesameasthetype

[2] zone with the following exception. If the system is

armed and the delay zone is NOT tripped during the Exit

Delay time, the type [3] zone will be bypassed. Instead of

the interior portion of an interior Home-away zone, a

Home-away zone can have a delay equal to the standard

Entryand Exit Delay when Section [32], light 3 isON.This

will affect all Home-away zones when they are not

bypassed by [∗][1][∗][9] arming, or by arming and not

leaving the premises. If Home-away zones are

automatically bypassed or [∗][9] arming bypassed and

the user then enters [∗][1], the Home-aways will then

have a delay.

[4] 24 Hour Bell isactive atall timesand willcreate analarm

if the panel is armed or disarmed. This zone will always

activate the bell/siren output.

[5] 24 Hour Bell/Buzzer operates as the type [4] except the

bell/sirenoutputisactivatedonlywhenthepanelisarmed

and only the keypad buzzer is activated while the panel

is disarmed.

[6] 24 Hour Buzzer operates as the type [4] except only the

buzzer will be activated in the armed or disarmed mode.

[7] Auxiliary Delay Zone operates the same as the type [0]

zone except the Entry/Exit Delays can be independently

set in Section [18]. This zone type is useful when a zone

with an Entry and/or Exit Delay is required that is different

from the standard times as established for type [0] zones

in Section [17]. If Section [32], light 5 is ON it will enable

the system to be armed even if the auxiliary delay zone is

open (“Ready”light ON). Also, the system can be armed

with the auxiliary delay zone closed and then it can be

opened before the Auxiliary Exit Delay has expired. In

bothcasestheauxiliarydelayzonewillnotbecomeactive

until both the Auxiliary Exit Delay has expired and the

zone is closed.

[8] FireZone Althoughacommonfiresignalisreported,any

numberofthe6zonesmaybeprogrammedasafirezone.

Afirezoneisasupervised(N.O.alarminitiatingcontacts),

end-of-lineresistorcircuitdesignedtoacceptlatching4-

wiresmokedetectors. Seethefirecircuitinstallationdrawing.

On alarm, fire zone shorted, the bell / siren will pulse to

indicatethatafirezonehasbeenactivated. Transmission

by the digital communicator is delayed 30 seconds. If

the alarm is acknowledged before the 30 second delay

has expired, pressing the [#] key will silence the alarm

and abort the transmission. If the alarm is NOT

acknowledgedwithinthe30secondperiod,transmission

will proceed and cannot be aborted. If the alarm has

been silenced and all smoke detectors are not restored

to normal, the alarm will re-sound after 90 seconds; 30

secondsafterthat,the communicator will transmit. If the

alarm re-sounds, it may again be silenced by pressing

the [#] key and the communicator transmission will be

aborted if the alarm is silence within the 30 second

transmission delay period.

To restore the smoke detectors to normal, clear all

productsofcombustionfromthe detectorsand performa

reset by pressing the [∗] then [7] keys. See Section [24]

for programming the PGM terminal for smoke detector

reset. Pressing [∗][7] will remove power from the smoke

detectors for 5 seconds; if the detectors are clear of

smoke,theywillreturntonormal. Ifthedetectorsstillhave

smoke in them, the alarm will re-sound and the sequence

described above will repeat.

For an open on any zone programmed for fire, the

“Trouble”light will come ON and the keypad sounder will

beep every 10 seconds. The keypad trouble buzzer will

sound and the “Trouble”light will come ON regardless of

whether the panel is armed or disarmed. The

communicator will transmit the trouble condition if

programmedinSection[09]. Theaudibletroubleindication

may be silenced by pressing the [#] key. The “Trouble”

light will only go OFF when all the fire zone troubles are

cleared. To determine the type of trouble, press [∗][2].

Section [11], Digit #2 Summary:

[0] = Standard Delay Zone

[1] = Instant Zone

[2] = Interior Zone

[3] = Interior Home/Away Zone

[4] = 24 hour Bell Zone

[5] = 24 hour Bell/Buzzer Zone

[6] = 24 hour Buzzer Zone

[7] = Auxiliary Delay Zone

[8] = Fire Zone

[12] 1st System Option Code

The 1st System Option Code is set using the zone lights as

shown in the table below. Once Section [12] is entered, the

6 zone lights will indicate the status of each option. Press a

numberkeycorrespondingtothezonelightnumbertoturnthe

option ON and OFF. Pressing [0] will turn all the zone lights

OFF and the options will be set as shown against “Light Off”.

ZONE

LIGHT

[1] ON = Communicator disabled

•OFF = Communicator Enabled

[2] ON = Transmission per 24 hour period

•OFF = Transmission per armed period

[3] •ON = Alarm display while armed

OFF = No alarm display while armed

[4] •ON = DTMF dialling*

OFF = Pulse dialling

[5] ON = N.C. zones (except fire zones)

•OFF = End-of-line resistor zones

[6] •ON = Keypad [P]anic audible

OFF = Keypad [P]anic silent

•Factory default settings

*DTMF dialling will default to pulse dialling after 2

unsuccessful DTMF dialling attempts.

[13] 2nd System Option Code

Use the same method of programming as Section [12].

ZONE

LIGHT

[1] •ON = Call 1st phone number only

OFF = Call 1st phone number with back-up to

2nd phone number

[2] ON = Master Code not user changeable

•OFF = Master Code user changeable

[3] ON = Bell squawk enabled*

•OFF = Bell squawk disabled

[4] ON = PC16OUT module enabled

•OFF = PC16OUT module disabled

[5] ON = 6th code is “maid’s code”(one-time use)

•OFF = 6th code is normal access code

[6] ON = 1400 Hz handshake for Radionics

formats # 3, 4, B and C

•OFF = 2300 Hz handshake for Radionics

formats # 3, 4, B and C

•Factory default settings

*With bell squawk enabled, the bell / siren will sound one

shortburst onarmingand twoshortbursts ondisarming.

NOTE:

Whenthe panelis set forAuto-Arming, the bell/ siren

will sound 1 short burst every 10 seconds for one minute

beforethepanelAuto-Armsunlessthe‘BellDuringAuto-Arm’

is disabled (Section [32], light 2).

[14] 3rd System Option Code

Use the same programming method as in Section [12]

ZONE

LIGHT

[1] ON = Access code required for bypass

•OFF = Access code not required for bypass

[2] ON = Enable [∗][4] downloading call feature

•OFF = Disable [∗][4] call feature1

[3] ON = Periodic downloading2

•OFF = Periodic test transmission

[4] ON = [∗][4] requires a access code

•OFF = [∗][4] does not require access code

[5] •ON = [P]anic key has keypad-audible feedback

OFF = [P]anic key without keypad-audible

feedback

[6] ON = Partial closings identified3

•OFF = Partial closings not identified

•Factory default settings

1The [∗][4] command can be enabled so that by using this

command the user or on-site installer can initiate a call to

the downloading computer.

2The panel can be enabled to periodically call the

downloading computer. The cycle time (in days) for the

call is set in Section [19]. The automatic call to the

downloading computer can be used to update the panel

program and/or to upload status information from the

panel.

3If partial closings are enabled as identified, then alarm

codes for the bypassed zones will be transmitted.

[15] Communication Variables

Once this section is entered, two 2-digit numbers are

expected. Donot press the [#] key whileentering data. The

first 2-digit number defines the number of attempts (alarm

and restoral pairs) per zone that the communicator will

makebeforeit shutsdown forthatzone (swingershutdown).

The number of attempts is for the period as defined in the

1st System Option Code Section, zone light 2. The number

ofattempts may be programmed from ‘00’to ‘99’, where ‘00’

means the communicator will never shut down. The fire

zone cannot be shut down - it always transmits.

The second 2-digit number defines the delay before

transmission. The delay if for zones defined as burglary

zonesonly. 24hourzonesorthefirezonewillnotbedelayed.

The time may be programmed from ‘00’to ‘99’seconds,

where ‘00’means no delay.

[16] Zone Bypass Mask

Use the same method of programming as used in Section

[12]. If the zone light is ON, the zone can be bypassed; if

OFF,thezonecannotbebypassedusingthe[∗][1]command.

The fire zone cannot be bypassed.

[17] System Times

There are 6 system times which can be programmed in this

section, and each entry requires a 3-digit number. Do not

press the [#] key during data entry.

[1] Entry delay time (001 to 255 seconds) This value

determines the standard Entry Delay time. The factory

default entry time is 30 seconds. See Section [11] for

zone definitions.

[2] Exit delay time (001 to 255 seconds) This value

determines the standard Exit Delay time. The factory

default exit time is 120 seconds. For zone definitions,

see Section [11].

[3] Bell cut-off time (001 to 255 minutes) This value

determines the time the bell / siren will sound before

automatically turning off. The factory default bell cut-off

time is 4 minutes.

[4] AC fail transmission delay (001 to 255 minutes) This

value determines the length of time before the

communicator will transmit an AC failure report. The

factory default time is 30 minutes.

[5] “Slow” zone response time (001 to 255 ×10 ms) This

value determines the “slow”zone response time and

provides times from 10 ms to 2550 ms. The factory

default“slow”zoneresponsetimeis500ms. NOTE: The

“fast”zone response time is fixed at 10 ms. See Section

[11] Zone Definitions.

[6] Test transmission cycle time (001 to 255 days) This

value determines the frequency, in days, of the test

transmission either via the communicator or by calling

the downloading computer. The factory default setting

is 30 days. See Section [14] 3rd System Option Code,

light 3.

[18] Auxiliary Delay Zone

Entry / Exit Times

This section requires two 3-digit entries to establish the

AuxiliaryEntryandExitDelaytimes. Donotpressthe[#]key

during data entry. The default Entry Delay is 45 seconds

and may be changed to any time from 001 seconds to 255

seconds. Thedefault ExitDelayis 120secondsand may be

changed to any time between 001 to 255 seconds.

For auxiliary delay zone times to be effective, the zone must

be programmed as a type [7] in the Zone Definition Section

[11].

[19] System Clock Times

This section requires two 4-digit entries to set the Automatic

Arming Time of Day and the Test Transmission Time of Day.

Do not press the [#] key during data entry. Factory default

for both these times is ‘9999’; that is, NO automatic arming

or test transmission will take place even if those functions

are enabled. VALID times must be entered in this section

before these features will function.

The system clock is in military time. Two digits from ‘00’to

‘23’are entered for the hour of the day and two digits from

‘00’to ‘59’are entered for the minute of the hour.

Test transmission or periodic downloading is selected in

Section [14] 3rd System Option Code, Light 3. The cycle

timeindaysforthetesttransmissionorperiodicdownloading

is set in Section [17] System Times. For a test transmission

using the communicator, an automatic test code should be

entered in Section [10]. For periodic downloading or a test

transmission using the communicator, a valid transmission

time must be entered in Section [19].

NOTE:

Upon power-up, if either the Auto-Arm or the test

transmissiontimehasavalidtimeentered,thenaloss-of-time

trouble for the system clock will be initiated. Enter [∗][2] to

view the trouble. Light 6 will be ON. If neither the Auto-Arm

or test transmission has a valid time, then the setting of the

system clock does not matter.

[20] New Installer’s Code

[21] New Master Code

[22] 2nd Master Code

Once the section number has been entered ([20], [21] or

[22]), enter a new 4-digit code. Only use digits 0 through 9

as code numbers. Do not press the [∗] or [#] keys. If an

error is made entering the code, complete entry of the 4

digits then enter the section number again to enter the

correct code. Do not press [∗] or [#] while entering the

code.

[23] Communication Formats

This section sets the type of format which will be sent to each

of the two telephone numbers programmed in Section [01]

and [03]. For each telephone number, enter one digit from

the list below. See the HEX data programming section for

details on how to enter digits ‘A’through ‘F’.

The selection for each phone number is determined by the

typeofreceiverbeing called. Entertheformatnumber forthe

1st telephone number first. It is necessary to program both

telephone format numbers even if the first phone number is

the only one being used.

[0] SILENT KNIGHT / ADEMCO SLOW 10 BPS

(1400 Hz handshake)

3/1, 4/1 and 4/2 non-extended formats

[1] SESCOA, FRANKLIN, DCI, VERTEX 20 BPS

(2300 Hz handshake)

3/1, 4/1 and 4/2 non-extended formats

[2] SILENT KNIGHT FAST 20 BPS

(1400 Hz handshake)

3/1, 4/1 and 4/2 non extended formats

[3] RADIONICS

(2300/1400 Hz handshake*)

3/1, 4/2 non extended formats

[4] RADIONICS

(2300/1400 Hz handshake)

3/1, 4/2 non-extended with parity format

[5] DO NOT USE

[6] DO NOT USE

[7] DO NOT USE

[8] SILENT KNIGHT, ADEMCO SLOW 10 BPS

(1400 Hz handshake)

3/1 extended format

[9] SESCOA, FRANKLIN, DCI, VERTEX 20 BPS

(2300 Hz handshake)

3/1 extended format

[A] SILENT KNIGHT FAST 20 BPS

(1400 Hz handshake)

3/1 extended format

[B] RADIONICS

(2300 / 1400 Hz handshake*)

3/1 extended format

[C]RADIONICS

(2300 / 1400 Hz handshake*)

3/1 extended with parity format

[D]DO NOT USE

[E] DO NOT USE

[F] DO NOT USE

* See Section [13] for Radionics handshake option.

10 BPS and 20 BPS Formats

10 BPS is the standard slow format used on Silent Knight /

Ademco receivers. DATA = 1900 Hz; KISSOFF = 1400 Hz;

SPEED = 10 baud

20 BPS is the standard fast format used on the DCI / Franklin

/ Sescoa and Vertex receivers. DATA = 1800 Hz; KISSOFF

= 2300 Hz; SPEED = 20 baud

Radionics Format

For conventional Radionics 3/1 format, the communications

mode should be set on either Radionics rounds [B] or

Radionics parity [C]. The extended version of the Radionics

formatisnormallyused. Thefollowingguidelinesareprovided

to help in configuring the PC1500 for Radionics format.

1. The customer account code must be only 3 digits with a

zero making up the 4th digit (i.e. Enter 1230 to program

an account code of 123).

2. The zone alarm reporting codes must all be single digit

numerical codes with no extended 2nd round being sent

(i.e. Zone 1 = 10, Zone 2 = 20... Zone 6 = 60). The zero

in the 2nd digit position tells the PC1500 not to send an

extended round.

3. All other non-alarm reporting codes must be set up to

send an extended 2nd round. The 1st digit of the

reporting code is used to identify the event while the 2nd

or extended digit is used to associate the event with a

particular item (i.e. A reporting code of E3 means restore

zone 3. E = restore, 3 = zone 3).

4. The following is a list of 1st digit identifiers that should be

used with the Radionics format.

•Restorals “E”

i.e. E3 = restore zone 3

•Openings “B”

i.e. B2 = opening by user 2

•Closings “C”

i.e. C4 = closing by user 4

•Troubles “F”

i.e. F5 = trouble from source 5

•Miscellaneous “D”

i.e. D1 = partial closing

[24] Programmable Output Options

(PGM Terminal)

The PGM output can be programmed in this section to

operate in response to various panel operations. The output

pulse connects the PGM terminal to the negative power rail.

[01] Ground Start Pulse

This option provides a 2-second output pulse before

dialling begins to obtain the dial tone on Ground Start

telephone equipment.

[02] Utility Output, no Access Code

When activated by entering the [∗][7] command, the

PGM output will go low for 5 seconds and the keypad

buzzer will sound.

[03] Utility Output, any Access Code

The same as [02], except the command is [∗][7] [any

valid access code].

[04] 5-Second Reset Pulse

When this option is selected, the PGM output is normally

low. That is, it is just the reverse of all other options which

arenormally high and go low whenactivated. Thisoption

isnormallyusedas thenegativereturnforpowerto4-wire

smokedetectors(positivecomesfromtheAUX+terminal).

To activate this output (to reset smoke detectors), enter

the [∗][7] command. The PGM terminal will go high

(open circuit), and thus remove power from the devices

connected. The keypad buzzer will sound for the 5-

second period.

[05] Courtesy Pulse

ThisoptionprovidesanoutputwhichfollowstheEntryand

ExitDelays. Itcan beusedto turnon acourtesylight near

the exit door for the duration of the Entry/Exit Delays.

[06] Keypad Buzzer Follow Mode

The PGM output will go low as long as the keypad buzzer

is ON for “24 Hour Buzzer Zone”, “Door Chime”, “Entry

Delay”and “Auto-Arm Alert”.

[07] System Status (Armed / Disarmed)

ThePGMoutputswitchestoandremainsatgroundaslong

asthe panel is armed. The output goes high (open) while

the panel is disarmed.

[08] Strobe Output (Latched Alarm Output)

ThePGMswitchestogroundonanalarmandremainslow

untilthe panelis disarmed. It canbe usedtoindicate that

an alarm has occurred before entering the premises.

[09] Failure to Communicate

The PGM output switches to ground if the systems fails to

communicate after 8 attempts to each phone number

that will be tried according to the communicator call

directionoptions. Theoutputremainslowuntilasuccessful

communication takes place or until trouble #4 is cleared

from the keypad. This option can be used to tie two

systems together so that if one fails to communicate, the

other system will report the failure.

[0A] PGM ON during Entry Delay

ThePGM outputwill beswitched onfor thedurationof the

Entry Delay. This option may be used to provide lighting

in the entrance area, or to activate a device when the

Entry Delay begins.

[0B] PGM ON during Exit Delay

ThePGM outputwill beswitched onfor thedurationof the

Exit Delay. This option may be used to provide lighting in

the exit area, or to activate a device when the Exit Delay

begins.

[0C] LINKS1000 Interface

This option configures the system for use with the

LINKS1000 Cellular Alarm Communicator. Refer to the

LINKS Installation Manual for further programming

instructions.

[25] Communicator Call Direction

This section requires four single digit entries using digits 0 to

3 only. This section defines how the communicator will call

the telephone numbers programmed in sections [01] and

[03] to report the following events:

•Zone Alarms and Restorals

•Access Codes Openings and Closings

•Priority Alarms and Restorals

•Maintenance Alarms and Restorals

Enter one digit from the list below for each of the above

categories. Factory default = 1 for all 4 code groups.

[0] Disables the function (no transmission for the group)

[1] Call 1stphonenumber and back-up to the 2nd phone

numberwhenSection[13]light1issettoOFFandthe

panelhas made8 unsuccessfultries onthe 1stphone

number.

[2] Call the 2nd phone number only

[3] Always call both phone numbers

Ifthe[#]keyispressedduringdataentry,youwillbereturned

to the installer’s programming mode and data for this section

will not be saved.

This manual suits for next models

Table of contents

Popular Security System manuals by other brands

Avtech

Avtech Sequoia 4H user manual

Gocontrol

Gocontrol 2GIG-CNTRL2 Operation & User’s Guide

Paradox

Paradox MG-6130 Reference and installation manual

LifeWatch

LifeWatch CL5 quick start guide

Metasys

Metasys IFC-1010 Technical Manual Programming Section

Verkada

Verkada BP41 install guide

Visonic

Visonic POWERMAX PRO Installer's guide

ArcVision

ArcVision ARC19020 user manual

Radio Shack

Radio Shack 49-1011 user manual

SkyLink

SkyLink DIAL-ALERT AD-433S Guide

Risco

Risco SecuSafe EL4855PI quick start guide

Compu-TTY

Compu-TTY KA300TX instruction manual

Federal Signal Corporation

Federal Signal Corporation 2001SRNB Installation and operating instructions

Detection Systems

Detection Systems SEFD1 user guide

Protect

Protect ZOLO quick guide

STI

STI 6400 quick start guide

FireAvert

FireAvert FA-E01-14-50 Installation and user guide

JRC

JRC JCX-161 installation manual

DSC PC-LINK9 User manual

Popular Security System manuals by other brands