Pyronix ENFORCER V11 Operating instructions

ENFORCER V11
PROGRAMMING GUIDE
Document SAP: 102028847-02

ii ENFORCER V11 PROGRAMMING GUIDE
DOCUMENT CONVENTIONS
TERMINOLOGY
INTERCHANGEABLE WORDS DESCRIPTION
Armed, set When an area or level is armed, if a zone is triggered, the system will follow
the appropriate (programmable) actions.
Disarmed, unset When an area or level is disarmed, the panel will not react unless specically
programmed to do so.
Siren, sounder, bell A warning device (usually external) that is generally congured to give
audible and visual notication that the system has been activated.
Area, partition
A group of zones assigned to be active when that particular area is armed.
This is usually named ‘Area A’ or renamed to a personal choice such as ‘Full Set’
or ‘Shop’.
Zone, input This refers to a detector or sensor connected to the system, whether this be
wired or wireless.
Output, PGM, PG
An output is a signal from the panel to instruct another device to operate.
This is usually a voltage that triggers a wired siren, a garage door, a wireless
siren etc.
Bypass, omit
The act of stopping a zone from becoming armed. A wired zone will still
detect an intruder or object but the system will not react to it - a wireless
zone will become dormant.
ICONS
Important information
This information should be read and taken into consideration when installing. Failure to do so
may result in faults and unexpected errors with the system and or peripherals.
Notes
Highlights parts of the process where extra care is needed or where sections of the programming
may be impacted by other options in the menus.
Hints
Helpful information for a smoother installation of the system.

3
ENFORCER V11 PROGRAMMING GUIDE
CONTENTS
Document Conventions ii
Terminology ii
Icons ii
Default Codes 5
Access Codes 5
Clean Start Codes 5
Other Codes 5
Engineer Menu Navigation 5
Accessing The Engineer Menu 5
Navigation 6
Main Menus and Sub-menus 6
Exiting The Engineer Menu 6
Engineer Menu Options 7
General Information 8
Initial Power Up 8
Testing the keypad 8
Wired Keypads and Readers 9
Keypads 9
Entering and exiting the keypad menu 9
Keypad menu options 9
Text programming 10
Misc button typing 10
The internal tag reader 10
The external proximity reader 10
Engineer arm system 11
Engineer forced arm on inputs 11
The Engineer Menu 12
Set Date & Time 12
Wireless Device Control 12
Control Inputs? 13
Learn devices? 13
Delete devices? 13
Control bells? 13
Delete devices 14
Control Keypad/Speaker? 14
Delete Devices 14
Program key fob buttons? 15
Change Inputs 16
Input Types 16
Input Areas 16
Input Attributes 17
Change Inputs Programming 18
Choose Mode 19
Install ZEMs 19
Change Outputs 20
Assign Keypads/Readers 21
Programming Keypads 22
Programming Readers 22
Set Point or Unset Only 22
Entry Control or Access Control 23
Keypad / Speaker Options 23
Change Timers 24
Commonly used timers 24
Occupancy Timer and Suspend 24
Codes And Users 25
Change Duress Codes 25

4ENFORCER V11 PROGRAMMING GUIDE
Change Master Manager Code 25
Change Engineer Code 26
Change Codes Programming 26
Volume Control 26
Volume Control Programming 27
System Options 27
Site Options 27
Occupancy Zones 29
System Displays 30
Exit Modes 30
Review Logs 30
Panel Log 30
Access Log 30
Engineer Tests 31
Walk Test Programming 32
Soak Control Programming 33
Test Siren, Battery Load Test and Outputs 33
Test Communications 33
Diagnostics 34
Wireless Devices 34
View Inputs 34
Signal Strength 34
Battery Status 34
Wireless Dual Frequency Menu 35
Wired Devices 35
View Inputs 35
View PSUs 35
Communications 35
Tablet Keypads 36
Wireless Device Diagnostics 36
Wired Device Diagnostics 36
Communications Diagnostics 37
Engineer Restore Options 37
Communications 38
Alarm Response 38
How Alarm Responses Work 38
Alarm Response Options 40
Set Up Downloading 41
Set Up Downloading via Cloud 41
Connecting to the InSite software 41
Set Up Downloading via RS232 42
Connecting to the InSite software: 42
Dial Out Menu 42
Software Revision 43
Clean Start 43
Exit Engineer Menu 43
Appendix A - Defaults 44
Appendix B - Input Types 51
Appendix C - Timers 52
Appendix D - Output Types 54
Appendix E - Fault Finding 57
Wireless Fault Displays 57
RS-485 Bus Problems 58
Power Supply Problems 58
Detection Faults 59
Communication Faults 59
Technical Support 59

5
ENFORCER V11 PROGRAMMING GUIDE
DEFAULT CODES
ACCESS CODES
User Code
‘Blank’
Master Manager Code
2222
Engineer
1111
CLEAN START CODES
Clean start with the code ‘2000’ (UNGRADED)
Clean start with the code ‘2020’ (Grade 2)
Hint: For information on the system clean start defaults, see“Appendix A - Defaults” on page 44
OTHER CODES
Keypad Security Code
2000
Delete All Wireless Data
2000
ENGINEER MENU NAVIGATION
The Engineer Menu must be accessed in order to program all system congurations.
Please note
1. All tamper alarms (including case tamper), will be disabled once in the Engineer Menu.
2. All personal attack and re alarms will not cause an alarm in the Engineer Menu.
ACCESSING THE ENGINEER MENU
Access to the Engineer Menu will be allowed if the system is disarmed. If armed, the system must be disarmed rst
via a valid user code, tag or keyfob in order to gain access. If the ‘Allow Engineer Menu’ function in the Master
Manager Menu is set as ‘No’, the message‘Authorisation Required’ will be shown and access will be denied until
this option is set as ‘Yes’.
1. Enter the Engineer code (default 1111).
2. If any faults that are active, they will be displayed now on the screen. Press hand enter the Engineer code
again.
3. ‘SET DATE & TIME?’ is displayed.
4. Engineer Menu has been accessed.
When the Engineer Menu is accessed, a high pitch tone is generated intermittently.
IMPORTANT NOTE: It is essential that a factory default (clean start) is performed after initial power up to
ensure that the correct defaults have been chosen.

6ENFORCER V11 PROGRAMMING GUIDE
NAVIGATION
h= ‘NO’ - Press to move forward when in Engineer or Master Manager mode.
b= ‘BACK’ - Press to move backward when in Engineer or Master Manger mode.
= ‘YES’ - Press to enter into a sub-menu or option when in Engineer or Master Manger mode.
= Press to move from one option into another option while in a sub-menu.
a= Press to quick exit the Engineer Menu from any main menu (written in capital letters).
c= ‘CANCEL’ - Press to move back from one programmable option to the previous option
MAIN MENUS AND SUBMENUS
SET DATE & TIME? Year (00-99)
[21]
A Main Menu item is identied by:
• The menu item will be in capital letters
A Sub-menu is identied by:
• The menu item will be in lower case letters
In order to navigate in the menu system, answer the questions in the main and sub menus. For example, if the
question ‘WIRELESS DEVICE CONTROL?’is displayed, then press or hdepending on the answer.
Pressing will enter a sub-menu called ‘Control Inputs?’in this example. Pressing will enter the
programmable options of this sub-menu. Pressing h will exit the individual option, move up from one sub-
menu to the next sub-menu or back to the main menu.
EXITING THE ENGINEER MENU
When a Main Menu Item (a menu that is in capital letters) is displayed, press or scroll to ‘EXIT ENGINEER
MENU?’ and press .

7
ENFORCER V11 PROGRAMMING GUIDE
ENGINEER MENU OPTIONS
ENGINEER MENU
SET DATE & TIME?
WIRELESS DEVICE CONTROL?
CHANGE INPUTS?
CHOOSE MODE?
INSTALL ZEMS?
CHANGE OUTPUTS?
ASSIGN KEYPADS/READERS?
CHANGE TIMERS?
CODES AND USERS?
VOLUME CONTROL?
SYSTEM OPTIONS?
REVIEW LOGS?
ENGINEER TESTS?
DIAGNOSTICS?
ENGINEER RESTORE OPTIONS?
COMMUNICATIONS?
ALARM RESPONSE?
SET UP DOWNLOADING?
DIAL OUT MENU
SOFTWARE REVISION?
CLEAN START?
EXIT ENGINEER MENU
Set date and time
Programs the date and time
“Set Date & Time”on page 12
Wireless device control
Learns and deletes all wireless zones, bells and arming
stations.
Hint: Wireless keyfobs are learnt to the system in the Master Manager Menu.
“Wireless Device Control” on page 12
Change inputs
Programs all zone types, attributes, areas and names.
“Change Inputs”on page 16
Choose mode
Congures the resistance range, EOL mode and response time
of the wired zones.
“Choose Mode”on page 19
Install ZEMs
Programs zone expansion modules (ZEMs) to the system.
“Install ZEMs”on page 19
Change outputs
Programs any outputs and assigns output modules on the
system.
“Change Outputs”on page 20
Assign keypads and readers
Assigns wired/wireless keypads and readers, and enables
readers for entry control.
“Assign Keypads/Readers” on page 21
Change timers
This function controls all timers on the system.
“Change Timers”on page 24
Codes and users
Changes the ‘Engineer code’,‘Master Manager code’ and
‘Duress codes’.
Hint: User codes are edited in the Master Manager menu.
“Codes And Users”on page 25
Volume control
Alters volume levels of the loudspeaker only. Volume levels of
keypads are programmed individually in the keypad menu.
“Volume Control” on page 26
System options
Contains sub-menus for conguring options such as how the system will operate day-to-day and system displays.
“System Options”on page 27
Review logs
View system events which are time and date stamped.
“Review Logs”on page 30
Engineer tests
Allows the engineer to test zones, outputs, batteries and the siren etc.
“Engineer Tests” on page 31

8ENFORCER V11 PROGRAMMING GUIDE
Diagnostics
Displays power, zone status, wireless arming stations, wireless signal strength and wireless battery levels.
“Diagnostics”on page 34
Engineer restore options
Congures which events can be reset by the user and which require an engineer.
“Engineer Restore Options”on page 37
Communications
Congures the signalling and smart device control of the system.
“Communications”on page 38
Alarm response
Controls how the system responds in certain situations such as conrmed activations.
“Alarm Response” on page 38
Set up downloading
Allows the system to be accessed remotely via upload/download software.
“Set Up Downloading”on page 41
Dial out menu
Used to dial out to pre-programmed upload/download software PCs.
“Dial Out Menu”on page 42
Software revision
This option identies all software revisions.
“Software Revision”on page 43
Clean start
Wipes all the data from the panel and reverts back to pre-dened factory conguration.
“Clean Start” on page 43
Exit engineer menu
Exits the menu and returns to day mode.
“Exit Engineer Menu”on page 43
GENERAL INFORMATION
Default Codes
Engineers
1111
Master Manager
2222
User
‘Blank’
INITIAL POWER UP
Power up the system and an alarm will be generated. Proceed to the on-board keypad, which will display:
1. Once power has been applied to the system,‘Please Wait’ will be displayed, followed by ‘485 Comms Lost’. After
approximately 1 minute, the system will display the time (00:00), indicating the system is ready to use.
2. The on-board keypad is defaulted to keypad address ‘0’.
Testing the keypad
With the system disarmed, press the key for 5 seconds at any keypad. This will cause all the LEDs on that
keypad to illuminate, and the LCD screen to display each pixel. The keypad will revert to normal display after the
test which will last about 10 seconds.

9
ENFORCER V11 PROGRAMMING GUIDE
WIRED KEYPADS AND READERS
Keypads
Three additional wired keypads may also be connected to the system for arming/disarming, programming and
entering text.
For help navigating menus, please see“Navigation”on page 6.
Hint: If any additional keypads are installed on the system, it is possible to access the Engineer Menu on any keypad. For example, if the Engineer menu
is accessed on keypad address 0, the other keypads will display ‘System Busy’. To access the Engineer menu on any other keypad, press the key on
the relevant keypad and the Engineer menu will be displayed.
Please note: Four wireless keypads can be connected to the system.
Entering and exiting the keypad menu
To enter the Keypad Menu, press and hold the dbutton until ‘SECURITY CODE:’is displayed, enter ‘2000’. To exit,
press the akey.
Keypad menu options
Address
Used to assign an address to a keypad.
Language
Allows you to assign a language to the keypad menu only.
Zone status
Displays the resistance of the two hard wired zones to the keypad terminals.
Key-click volumes
Alters the volume of the tone heard when a keypad button is pressed.
Tag volume
Sets the volume when tag is presented.
Keypad volume
Sets the general volume of the keypad.
ID tag
Used to read the unique ID number of the tag.
Reset keypad
Resets the keypad to factory settings.
Backlight force
Change to ‘1’ to force the LCD back-light on all the time. If left on ‘0’, the LCD will dim after 30 seconds.
PA/Fire timer
Congures how long the HU and Fire buttons have to be pressed for before an alarm is generated.

10 ENFORCER V11 PROGRAMMING GUIDE
Text programming
On the system it is possible to label items such as the following:
• Zones – Two labels; zone name and location
• Area names
• Site name
• Keypad/reader – Two labels; keypad description and location
• Zone and output expander location descriptions
• User names
The control panel incorporates a predictive text feature, and works like so:
Enter ‘B’ and ‘Bedroom’will be displayed. If the word that is required does not appear, then type the word letter by
letter.
Hint: To type a word, press the relevant button the appropriate number of times – e.g. for the letter ‘k’ press 5two times, or for the letter‘s’ press 7
four times. For punctuation marks, press the 1button multiple times until the desired character is shown.
Misc button typing
BUTTON TEXT FUNCTION
aToggles between upper and lower case characters
bMoves cursor left
cClears letters / adds a space
dMoves cursor right
[]Moves the cursor left and right
The internal tag reader
The Internal tag reader can be used for arming/disarming, entry control or access control. Refer to the installation
manual for all connections.
Tag area (where a proximity tag/card must be presented to arm/disarm)
Blue LED
Alert
Amber LED
Alarm
Red LED
Tamper
Red LED
Fault
Amber LED
Disarmed
Green LED
The external proximity reader
The external proximity reader can be used for arming/disarming, entry control or access control. Refer to the
installation manual for all connections.
To arm/disarm the system using the external proximity reader, present a pre-
programmed tag to the centre of the unit.
The unit will display the system status:
• Green indicates the system is disarmed.
• Red indicates the system is armed.
Present the tag again within 10 seconds to arm or disarm the system.
Please note: The system will arm depending on the type of exit mode programmed (nal door, timed or
push to set)