DSE 7420 User manual

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR.
•
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset button.
• Press the Stop/Reset and Info buttons simultaneously.
• If a module security PIN has been set, the PIN number re uest is then
shown :
• Press the button the first digit will flash to enable the pin to be entered.
• Press
(up) or (down to adjust it to the correct value)
• Press (right) when the first digit is correctly entered. The digit you have just entered will now
show ‘#’ for security.
• Repeat this process for the other digits of the PIN number. You can press (left) if you need to move
back to adjust one of the previous digits.
•
When is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
EDITING A PARAMETER
• Enter the editor as described above.
• Press the or to cycle to the section you wish to view/change. Then press or
to cycle to the parameter within the section you have chosen.
• To edit the parameter, press to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
• Press the up
or down buttons to change the parameter to the re uired value.
• Press to save the value. The parameter ceases flashing to indicate that it has been saved.
•
To exit the editor at any time, press and hold the
or
button
.
D E E P S E A E L E C T R O N I C S
7 4 2 0 I N S T AL L AT I O N I N S T R U C T I O N S
053-088
ISSUE 2
TYPICAL WIRING DIAGRAM
A lar er dia ram is available in the operators manual.
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
Email: [email protected]
Web: www.deepseaplc.com
Deep Sea Electronics inc.
Phone: [phone]
Fax: [phone]
TOLL FREE (USA only) : Tel: [phone]
Email: [email protected]
Web: www.deepseausa.com
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security.
NOTE: More comprehensive module confi uration is possible usin the 86xx series PC
confi uration software. Please contact us for further details
NOTE: The contents of the tables overleaf may differ dependin on the actual module
confi uration.
DIMENSIONS AND MOUNTING
For flat surface mounting in a Type 1 enclosure.
DIMENSIONS
240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)
PANEL CUTOUT:
220mm x 160mm (8.7” x 6.3”)

ADJUSTABLE PARAMETERS
Front Panel Confi uration Editor
Section Parameter as shown on display Values
Display
Contrast 53%
Language
English, others.
Current Date and Time
hh:mm
Timers
LCD Page Timer
5m
Scroll Delay
2
s
Engine Pre Heat Timer
0s
Engine Crank Duration
10s
Engine Crank Rest Time
10s
Engine Safety On Delay
10s
Engine Smoke Limiting
0s
Engine Smoke Limiting Off
0s
Engine arm Up Time
0
s
Engine Cool Down Time
1m
Engine Speed Overshoot Delay
0s
Engine Failed To Stop
30s
Battery Under Voltage arning Delay
1m
Battery Over Voltage arning Delay
1m
Return Delay
30s
Generator Transient Delay
0s
Mains Transient Delay
2s
Mains transfer time
0.7s
Mains
Mains Under Voltage Alarm
184v
Mains Over Voltage Alarm
277v
Mains Under Frequency Alarm
45Hz
Mains over Frequency Alarm
55Hz
Mains Transient Delay
2s
CT Primary
600A
CT
Secondary
5A
Mains k
Rating
345k
Mains k
Var Rating
258k
Generator
Under Voltage Shutdown
184v
Under Voltage Pre-Alarm 196v
Nominal Voltage 230v
Over Voltage Pre-Alarm 265v
Over Voltage Shutdown 277v
Under Frequency Shutdown 40Hz
Under Frequency Pre-Alarm 42Hz
Nominal frequency 50Hz
Over Frequency Pre-Alarm 54Hz
Over Frequency Shutdown 57Hz
Full Load Rating 500A
k Overload Trip 100%
Delayed Over current Active
Delayed Over Current 100%
AC System 3 Phase 4 ire
CT Primary 600A Power Cycle After Exit
CT Secondary 5A Power Cycle After Exit
Short Circuit Trip 200%
Earth CT Primary 500A
Earth Fault Trip Active
Earth Fault Trip 10%
Transient Delay 0s
Gen Reverse Power Delay 2s
Gen Reverse Power 35k
En ine
Oil Pressure Low shutdown 1.03bar
Oil Pressure Low Pre-Alarm 1.24bar
Coolant Temp High Pre-Alarm 90ºC
Coolant Temp High Electrical Trip 92ºC ( hen Enabled)
Coolant Temp High Shutdown 95ºC
Start Delay Off load 5s
Start Delay on load 5s
Start Delay Telemetry 5s
Pre Heat Timer 0s
Crank Duration 10s
Crank rest Time 10s
Safety On Delay 10s
Smoke Limiting 0s
Smoke limiting off 0s
arm Up Time 0s
Cool Down Time 1m
Speed Overshoot Delay 0s
Speed Overshoot 0%
Fail To Stop Delay 30s
Battery Under Volts arning Active
Battery Under Volts arning Delay 1m
Battery Under Volts arning 10v
Battery Over Volts arning Active
Battery Over Volts arning Delay 1m
Battery Over Volts arning 30v
Charge Alternator Failure arning Active
Continued Overleaf
Front Panel Confi uration Editor (continued)
Section Parameter as shown on display Values
En ine (continued)
Charge Alternator Failure arning
6.0v
Charge Alternator arning Delay
5s
Charge Alternator Failure Shutdown
Ina
ctive
Charge Alternator Failure Shutdown
4.0
v
(When Enabled)
Charge Alternator Shutdown Delay
5s
(When Enabled)
Droop %
Active, Inactive. Electronic engines only when
droop is enabled.
Scheduler
Scheduler
Active,
Inactive
Schedule On Load
Active , Inactive (Only Available When
Scheduler Is Active)
Schedule Period
Weekly, Monthly (Only Available When
Scheduler Is Active)
Schedule Time & Date Selection (1-16)
Press to begin editing then or
when selecting the different
parameters in the scheduler.
ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR
• The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.
• Press and hold the button to enter the running editor.
ADJUSTABLE PARAMETERS (Runnin editor)
• Enter the editor as described above.
• Press the up or down buttons to cycle to the section you wish to view/change.
•
To Edit the parameter press the button to enter edit mode. The parameter begins to flash to
indicate that you are editing the value.
• Press the up or down buttons to change the parameter to the re uired value.
• Press the button to save the value. The parameter ceases flashing to indicate that it has been
saved.
• To exit the editor at any time , press and hold the button.
Runnin Editor
Section Parameter as shown on display Factory Settin s
DISPLAY
Contrast
53%
Language
English