DSE DSE8610 MKII Service manual

TYPICAL WIRING DIAGRAM
NOTE: A larger version of the Typical Wiring Diagram is available in the product’s operator manual, refer to
DSE Publication: 057-254 DSE8610 MKII Operator Manual available from www.deepseaplc.com for more
information.
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
Email: [email protected]
Web: www.deepseaplc.com
Deep Sea Electronics Inc.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.deepseausa.com
DEEP SEA ELECTRONICS
DSE8610 MKII Installation Instructions
053-182
ISSUE 3
ACCESSING THE MAIN CONFIGURATION EDITOR
•Ensure the engine is at rest and the module is in STOP mode by pressing the
(Stop/Reset) button.
•Press the (Stop/Reset) and (Tick) buttons simultaneously.
•
If a module security PIN has been set, the PIN number request is then shown:
•The first ‘#’ changes to ‘0’. Press the (Up) or (Down) button to adjust it to the correct value.
•Press the (Right) button when the first digit is correctly entered. The digit previously enterednow shows ‘#’ for security.
•Repeat this process for the other digits of the PIN number. Press the (Left) button to move back to adjust one of the previous
digits.
• When the (Tick) button is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is not correct,
the PIN must be re-entered.
•
If the PIN has been successfully entered (or the module PIN has not been enabled), the editor is
displayed:
EDITING A PARAMETER
•Enter the editor as described above.
•Press the (Right) or (Left) buttons to cycle to the section to view/change.
•Press the (Up) or (Down) buttons to select the parameter to view/change within the currently selected section.
•To edit the parameter, press the (Tick) button to enter edit mode. The parameter begins to flash to indicate editing.
•Press the (Up) or (Down) buttons to change the parameter to the required value.
•Press the (Tick) button to save the value. The parameter ceases flashing to indicate that it has been saved.
•To exit the editor and save the changes, press and hold the (Tick) button.
•To exit the editor and not save the changes, press and hold the (Stop/Reset) button .
NOTE: If the editor is left inactive for the duration of the LCD Page Timer, it is automatically exited to ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or automatically) to ensure security.
NOTE: Comprehensive module configuration is possible using the DSE Configuration Suite PC Software, refer to DSE
publication 057-239 DSE8610 MKI Configuraiton Suite PC Software Manual available from www.deepseaplc.com.

MAIN CONFIGURATION EDITOR PARAMETERS
NOTE: Depending upon module configuration, some values in the may not be
available. For more information refer to DSE publication 057-239 DSE8610 MKII
Configuraiton Suite PC Software Manual available from www.deepseaplc.com
Section
Parameter As Shown On Display
Values
Display
Contrast 0%
Language English, Other.
Current Date and Time hh:mm
Engine
Oil Pressure Low Shutdown 0.00 bar
Oil Pressure Low Pre Alarm 0.00 bar
Coolant Temp high Pre Alarm 0 ºC
Coolant Temp High Shutdown 0 ºC
Start Delay Off Load 0h 0m 0s
Start Delay Telemetry 0h 0m 0s
Engine Pre Heat Timer 0h 0m 0s
Engine Crank Duration 0h 0m 0s
Engine Crank Rest Time 0h 0m 0s
Engine Safety On Delay 0h 0m 0s
Engine Smoke Limiting 0h 0m0s
Engine Smoke Limiting Off 0h 0m 0s
Engine Warm Up Time 0h 0m 0s
Engine Cool Down Time 0h 0m 0s
Engine Speed Overshoot Delay 0h 0m 0s
Engine Speed Overshoot 0h 0m 0s
Engine Failed To Stop Delay 0h 0m 0s
Battery Under Voltage Warning Active / Inactive
Battery Under Voltage Warning Delay
0h 0m 0s
Battery Under Voltage Warning 0 V
Battery Over Voltage Warning Active / Inactive
Battery Over Voltage Warning Delay 0h 0m 0s
Battery Over Voltage Warning 0 V
Charge Alternator Failure Warning Active / Inactive
Charge Alternator Failure Warning 0 V
Charge Alternator Warning Delay 0h 0m 0s
Charge Alternator Failure Shutdown Active / Inactive
Specific Gravity 0.80 to 1.00
CAN Termination Active / Inactive
Generator
Under Voltage Shutdown 0 V
Under Voltage Pre-Alarm 0 V
Loading Voltage 0 V
Nominal Voltage 0 V
Over Voltage Pre-Alarm 0 V
Over Voltage Shutdown 0 V
Under Frequency Shutdown 0 Hz
Under Frequency Pre-Alarm 0 Hz
Loading Frequency 0 Hz
Nominal frequency 0 Hz
Over Frequency Pre-Alarm 0 Hz
Over Frequency Shutdown 0 Hz
Full Load Rating 00 A
kW Overload Trip 0 %
Delayed Over current Active / Inactive
Gen Over Current Trip 0 %
AC System 3 Phase 4 Wire
CT Primary
0 A
Power Cycle After Exit
CT Secondary
0 A
Power Cycle After Exit
Short Circuit Trip 0 %
Earth CT Primary 0 A
Earth Fault Trip Active / Inactive
Earth Fault Trip 0 %
Transient Delay 0h 0m 0s
Gen Reverse Power Delay 0h 0m 0s
Full kW Rating 0 kW
Full kVAr Rating 0 kvar
Load Ramp Rate 0 %
Load Level For More Sets 0 %
Load Level For Less Sets 0 %
MAIN CONFIGURATION EDITOR PARAMETERS (CONTINUED)
Section
Parameter As Shown On Display
Values
Generator
Load Demand Priority 1
(Continued)
Gen Reverse Power 0 kW
Insufficient Capacity Delay 0h 0m 0s
Insufficient Capacity Action None / Indication / Warning /
Shutdown / Electrical Trip
Reactive Load CTL Mode None / VAr Share
Load Parallel Power
0 kW
In Mains Parallel Mode
Load Power Factor
0 %
In Mains Parallel Mode
Enable MSC Compatibility Active / Inactive
Timers
LCD Page Timer 0h 0m 0s
Scroll Delay 0h 0m 0s
Engine Pre Heat Timer 0h 0m 0s
Engine Crank Duration 0h 0m 0s
Engine Crank Rest Time 0h 0m 0s
Engine Safety On Delay 0h 0m 0s
Engine Smoke Limiting 0h 0m0s
Engine Smoke Limiting Off 0h 0m 0s
Engine Warm Up Time 0h 0m 0s
Engine Cool Down Time 0h 0m 0s
Engine Speed Overshoot Delay 0h 0m 0s
Engine Failed To Stop Delay 0h 0m 0s
Battery Under Voltage Warning Delay
0h 0m 0s
Battery Over Voltage Warning Delay 0h 0m 0s
Return Delay 0h 0m 0s
Generator Transient Delay 0h 0m 0s
Scheduler
Scheduler Active / Inactive
Schedule On Load Active / Inactive
Schedule Period Weekly, Monthly
Schedule Time & Date Selection (1-
16)
Press to begin editing then
or when selecting the
different parameters in the
scheduler.
DIMENSIONS AND MOUNTING
DIMENSIONS
245 mm X 184 mm X 51 mm
(9.6” X 7.2” X 2.0”)
PANEL CUTOUT
220 mm X 160 mm
(8.7” X 6.3”)
WEIGHT
0.98 kg
(2.16 lb)
TEMPERATURE
Operating: -40 ºC to +70 ºC
(-40 ºF to +158 ºF)
Storage: -40 ºC to +80 ºC
(-40 ºF to +176 ºF)
ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR
•The ‘running’ editor can be entered while the engine is running. All protections
remain active if the engine is running while the running editor is entered.
•Press and hold the (Tick) button to enter the running editor.
RUNNING CONFIGURATION EDITOR PARAMETERS
Section
Parameter As Shown On Display
Values
Display
Contrast 0 %
Language English, Other
Load Demand Priority 1
Load Power Factor 0 %
Load Parallel Power 0 %
)
Commissioning Screens Active / Inactive
Override Starting Alarms Active / Inactive
Voltage Adjust
(manual mode only engine running breaker open) 0 %
Frequency Adjust
(manual mode only engine running breaker open) 0 %
REQUIREMENTS FOR UL CERTIFICATION
WARNING!: More than one live circuit exists, see diagram overleaf for further
information.
Specification
Description
Screw Terminal
Tightening Torque •4.5 lb-in (0.5 Nm)
Conductors
•
Terminals suitable for connection of conductor size 13 AWG
to 20 AWG (0.5 mm² to 2.5 mm²).
•Conductor protection must be provided in accordance with
NFPA 70, Article 240
•Low voltage circuits (35 V or less) must be supplied from the
engine starting battery or an isolated secondary circuit.
•The communication, sensor, and/or battery derived circuit
conductors shall be separated and secured to maintain at
least ¼” (6 mm) separation from the generator and mains
connected circuit conductors unless all conductors are rated
600 V or greater.
Current Inputs
•
Must be connected through UL Listed or Recognized isolating
current transformers with the secondary rating of 5 A max.
Communication
Circuits
•
Must be connected to communication circuits of UL Listed
equipment
DC Output Pilot Duty
•
0.5 A
Mounting
•
Suitable for flat surface mounting in Type 1 Enclosure Type
rating with surrounding air temperature -22 ºF to +122 ºF (-30
ºC to +50 ºC)
•Suitable for pollution degree 3 environments when voltage
sensing inputs do not exceed 300 V. When used to monitor
voltages over 300 V device to be installed in an unventilated
or filtered ventilation enclosure to maintain a pollution degree
2 environment.
Operating
Temperature •-22 ºF to +122 ºF (-30 ºC to +50 ºC)