DTY Broadmoor OF-1001 User manual

Broadmoor Wood Bench OF-1001 www.DTYStore.com Page 1of 5
Broadmoor Wood Bench
Item No. OF-1001
Made in Vietnam
For assistance with assembly, please contact DTYStore.com Customer Satisfaction Center
866-217-8155 . [e-mail]

Broadmoor Wood Bench OF-1001 www.DTYStore.com Page 2of 5
Pre-Assembly Instructions
•Read all instructions carefully before assembly.
•Find a smooth clean area in which to work to avoid damaging your item.
•Check that all parts and hardware from the lists are present.
•Lay out parts in alphabetical order and hardware in numerical order to make them easier to
find when you are ready to assemble
•Wait to dispose of packing material until assembly is complete to avoid accidentally
disposing of small parts or hardware
•Tools required: Hex wrench (included) Phillips screwdriver and flathead screwdriver (not
included)
•Please use caution and care when lifting the product to avoid injury
•For ease of assembly two people are recommended
Parts List:
C. Back Qty: 1
D. Seat Cross-Bar Qty: 1
E. Leg Cross- Bar Qty: 1
A. Leg Qty: 2
B. Seat Qty: 1

Broadmoor Wood Bench OF-1001 www.DTYStore.com Page 3of 5
Hardware List:
1. Bolt/Barrel Nut Qty: 4
2. Long Screw (90mm long)
Qty: 4
3. Medium Screw (60mm long)
Qty: 2
4. Short Screw (35mm long) Qty: 4
5. Hex Wrench Qty: 2
Assembly Instructions:
Step 1
Wait to fully tighten all hardware until the end of Step 3.
Use two Bolts/Barrel Nuts (1) and one Long Screw (2) to loosely attach one Leg (A) to the Back
(C).
Use one Long Screw (2) to loosely attach the Seat Cross-Bar (D) to the front of the Leg (A). Be
sure the block is at the bottom and facing the back of the bench.
Use one Medium Screw (3) with to loosely attach the Leg Cross bar (E) to the middle of the
Leg (A)

Broadmoor Wood Bench OF-1001 www.DTYStore.com Page 4of 5
Step 2
Use two Bolts/Barrel Nuts (1), two Long Screws (2), and one Medium Screw (3) and Hex Wrench
(5) to loosely attach the Leg (A) to the Back (C), Seat Cross-Bar (D) and Leg Cross-Bar (E). Insert
Seat (B)

Broadmoor Wood Bench OF-1001 www.DTYStore.com Page 5of 5
Post-Assembly Instructions:
•Periodically check hardware to be sure it does not loosen overtime.
•Do not stand on this item.
Outdoor Furniture Care Instruction:
With the proper care your premium eucalyptus furniture will last up to 25 years or more. For
unfinished furniture, we suggest lightly sanding the surface of the furniture with 150 or 180 grit
sandpaper once a year to remove any fuzziness and any larger splinter causing
fibers that occur due to exposure to the elements. Be sure to sand lightly to retain the natural
patina. Furniture with an oil finish should also be treated yearly with a light coat of wood oil
designed for eucalyptus or teak by applying it with a soft cloth. For finished furniture, we
recommend brushing off any loose dirt or debris with a soft brush and wiping down with a mild
detergent and water. We recommend you protect your furniture in the off season by using
a using a good quality furniture cover. It helps keep your furniture clean and protects it from the
elements thus minimizing annual maintenance.
Step 3
From the underside of the Seat, use four Short Screws (4) with the Hex Wrench to loosely
attach the Seat to the Legs.
Use the Hex Wrench to fully tighten all bench hardware.