DTY OF-1015 User manual

Aspen Plantation Chair OF-1015
www.DTYStore.com
Page 1 of 4
Aspen Plantation Chair
Item No. OF-1015
Made in Vietnam
For assistance with assembly, please contact DTYStore.com Customer Satisfaction Center
866-217-8155 . [email protected]

Aspen Plantation Chair OF-1015
www.DTYStore.com
Page 2 of 4
Pre-Assembly Instructions
Read all instructions carefully before assembly.
Find a smooth clean area in which to work to avoid damaging your item.
Check that all parts and hardware from the lists are present.
Lay out parts in alphabetical order and hardware in numerical order to make them easier to find when you
are ready to assemble
Wait to dispose of packing material until assembly is complete to avoid accidentally disposing of small parts
or hardware
Tools required: Hex wrench (included)
Please use caution and care when lifting the product to avoid injury
For ease of assembly two people are recommended
Parts List:
1. Sides
left right
2. Back
Qty: 1
3. Small Seat
Qty: 1
4. Large Seat
Qty: 1
5. End
Qty: 2
6. Leg
Qty: 2
7. Cross-Bar
Qty: 2
Hardware List:
A. Medium Screw (70mm long)
Qty: 8
B. Short Screw (45mm long)
Qty: 12
C. Long Screw (120mm long)
Qty: 4
D. Hex Wrench
Qty: 1

Aspen Plantation Chair OF-1015
www.DTYStore.com
Page 3 of 4
Assembly Instructions:
Step 1
a. Use two Medium Screws (A)
to secure the Ends (5) to one
of the Sides. Note the
orientation of the Ends.
b. Note the steel pins in the
sides of the Large Seat (4),
the Small Seat (3), and the
Back (2). Insert these pins in
the holes of the Side.
c. Partially insert six Short
Screws (B) to loosely attach
the Large Seat (4), the Small
Seat (3), and the Back (2) to
the Side.
d. Follow a, b, and c to loosely
attach these parts to the
other Side.
e. Use the Hex Wrench (D) to
fully tighten all 16 Screws.
BA
A
B
steel pins
A
A

Aspen Plantation Chair OF-1015
www.DTYStore.com
Page 4 of 4
Step 2
Use two Medium Screws (A) to
loosely attach the two Cross-Bars (7)
to one of the Legs (6).
Use two Medium Screws (A) to
loosely attach the two Cross-Bars (7)
to the other Leg (6).
A
A
A
A
Step 3
Use four Long Screws (C) to loosely
attach the Legs (6) to the Sides as
shown.
Use the Hex Wrench (D) to tighten all
eight Screws from Steps 2 and 3.
Post-Assembly Instructions:
Periodically check fasteners to be sure they do not loosen over time.
Do not stand on this item.
Outdoor Furniture Care Instruction:
With the proper care your premium eucalyptus furniture will last up to 25 years or more. For unfinished
furniture, we suggest lightly sanding the surface of the furniture with 150 or 180 grit sandpaper once a year to
remove any fuzziness and any larger splinter causing fibers that occur due to exposure to the elements. Be sure
to sand lightly to retain the natural patina. Furniture with an oil finish should also be treated yearly with a light
coat of wood oil designed for eucalyptus or teak by applying it with a soft cloth. For finished furniture, we
recommend brushing off any loose dirt or debris with a soft brush and wiping down with a mild detergent and
water. We recommend you protect your furniture in the off season by using a using a good quality furniture
cover. It helps keep your furniture clean and protects it from the elements thus minimizing annual
maintenance.