Dukane WMIC2B User manual

WMIC2BQUICK START GUIDE Wireless Mic System
14-00055-01
Speaker top view connections
AUX OUT TO
OTHER
SPEAKER HALF
DC POWER IN
AUX AUDIO INPUT
(OPTIONAL) FROM
PROJECTOR
For initial setup the speaker system can be assembled and tested on a table top. Then install on the pole.
5. Connect the DC Power cable to the speaker top. Then
plug in the power adapter to the 115VAC. A blue LED will
be visible behind the black speaker grill.
4. Audio Cable connections
Page 1 of 2
4.Connect main speaker section
to other section with audio cable
Optional Audio cable from projec-
tor output to speaker AUX AUDIO
INPUT Projector
4. Connect the Audio cable be-
tween the 2 speaker sections.
Installing on a pole
Place the foam pads on the inside of the speaker.
Connect the 2 halves of the speaker around the
pole using the metal hooks. Insert a wedge to
hold the speaker in place if necessary.
Enlarged
view of foam
pads
Clip-on MIC
Charging the MIC TRANSMITTER Battery
The miniature MIC TRANSMITTER is charged using
the cable with the USB connector and the small DC
power connector pin which inserts into the top of the
TRANSMITTER. The USB end is plugged into a
powered USB port such as on a computer. A constant
on red LED indicates the battery is charging.
Please be sure the USB port remains active. If the
computer goes to sleep the port will go OFF and the
port will discharge or drain the TRANSMITTER
battery
Other Details
This wireless system operates in the 2.4Ghz
region and uses 1 of 20 available channels that
are automatically selected. There are 4 models of
operation. The AUX AUDIO input or the MIC
input can be set to have priority over the other.
The wireless mic operating range is beyond 80
feet. The transmitter contains a Li battery.
Multiple systems should be at least 18 feet from
each other.

Page 2 of 2
Multi-function switch
- Top and right side are
Volume increase.
- Center is switch between
MIC and Audio Inputs.
- Bottom and left side are
Volume decrease.
MINIATURE MIC TRANSMITTER
Top View ( For charging)
Red and Blue LED
Optional audio input
External Clip-
on MIC
Mic Transmitter top view
Power adapter or PC
USB port (5 VDC)
Charging cable
WMIC2 QUICK START GUIDE
Microphone and Transmitter (See images below)
1. Plug the Clip-on Mic cord into the center MIC phone jack on the Transmitter.
2. Bring the Mic/ Transmitter within 8 feet of the Speaker.
3. Turn ON the mini Transmitter ( Power ON). Red LED Signal light will appear.
4. The transmitter will seek the receiver which is inside the speaker. When matching (pairing) is completed, takes about 3 sec-
onds, a beep-beep sound will be heard, While pairing the transmitter red/blue LEDs will flash. Note: Do not cover the bot-
tom of the transmitter during pairing since an IR LED signal is emitted from the transmitter.
5. The Mic should now be active. Adjust Volume. If no sound is present press the center button on the Multi-functional switch to
change the inputs. Also check to see that the speaker is powered ON.
6. The MIC talk time exceeds 8 hours. The red LED on the transmitter starts flashing when there is 1 hour of operating time
remaining. Recharge the battery continuously for 4 hours. Use the cable with the USB connector to the USB Power Adapter
or to the USB port on a PC.
If the matching (pairing) of the system does not occur the MIC TRASMITTER may need to be reset. Turn the MIC
TRANSMITTER OFF. Then press and hold a button on the multifunction switch and turn ON the MIC TRANSMITTER.
Release the button after the red LED comes ON.
Speaker Top View connections
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487
Fax [phone]
[email protected]
http://www.dukane.com/av/service/
B
Mode Setup – Settings for the AUX AUDIO INPUT on the Speaker
There are 4 modes of operation for the AUX AUDIO input on the top of the speaker unit. This Input is located next to the DC INPUT. The
audio entering this port can be set to operate in one of 4 ways.
Mode 1. MIC Only: Only sound from the Miniature MIC TRANSMITTER is amplified. No AUDIO AUX (it is turned Off)
Mode 2. Mixed audio; The MIC TRANSMITTER and AUX AUDIO INPUT are mixed.
Mode 3. MIC priority operation; The MIC audio, when present, will have the priority and turn off the AUX AUDIO.
Mode4. AUX AUDIO INPUT priority; The Aux IN on the speaker unit will have priority over the Mic input .
Setting the mode. The MIC TRANSMITTER is used to set the mode. Start with it OFF.
Mode 1. Hold down the MIC TRANSMITTER key 1 (Volume up) button and turn ON the power.
Mode 2. Hold down the MIC TRANSMITTER key 2 (Right key) button and turn ON the power
Mode 3. Hold down the MIC TRANSMITTER key 3 (Volume down) button and turn ON the power.
Mode 4 Hold down the MIC TRANSMITTER key 4 ( Left key) button and turn ON the power.
See the figure.