Dulytek DW4000 User manual

HEAT PRESS
MODEL No: DW4000
CONTACT
INSTRUCTION MANUAL
Dulytek Equipment
Seatle, WA 98105
[email protected]
www.dulytek.com
© 2018 Dulytek
All rights reserved

Dulytek Equipment
www.dulytek.com Email: [email protected]
INSTRUCTION MANUAL: DW4000
TABLE OF
CONTENTS
PAGE 2 INTRODUCTION
Read Before Operating Machinery
Copyright Notice
Disclaimer
PAGE 3 SAFETY PRECAUTIONS
PAGE 4 HANDLING PRECAUTIONS
PAGE 5 UNPACKING
Unpacking Precautions
Unpacking Instructions
Item Checklist
Recommended Parts
PAGE 6 GETTING FAMILIAR
DW4000 Press Parts, Features, and Controls
PAGE 7 ASSEMBLY INSTRUCTIONS
Assembly
PAGE 8 OPERATING INSTRUCTIONS
Preparing and Starting the Press
Setting Control Panels
Pressing
    TurningO󰀨thePress
Calibrating Temperature Controls
PAGE 12 TECHNICAL SPECIFICATIONS
PAGE 1
© 2018 Dulytek
All rights reserved

INTRODUCTION
DULYTEK DW4000 manual heat press is a machine engineered and manufactured for solvent-less
plant rosin oil extraction for individual use or small operation businesses in research laboratories,
pharmaceutical, cosmetic, food processing, and brewing industries.
INSTRUCTION MANUAL: DW4000 PAGE 2
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
Toavoidaccidents,rstreadSAFETYPRECAUTIONS(PAGE3)andHAN-
DLINGPRECAUTIONS(PAGE4).
Read this manual carefully to ensure you use the press correctly. After read-
ing and familiarizing yourself with the equipment, store the manual in a safe
place for future references.
READ BEFORE
OPERATING
MACHINERY
Copyright © 2018 by DULYTEK. All rights reserved. No part of this document
may be reproduced, distributed, or transmitted in any form or by any means,
including photocopying, recording, or other electronic or mechanical meth-
ods, without the prior written consent of the company. Product design, logos,
brand names for various media, and product photos are the sole and exclu-
sive property of DULYTEK.
COPYRIGHT
NOTICE
This unit is intended for LEGAL use only, in accordance with your federal,
state, and local laws, ordinances, and regulations.
Please keep this manual in a safe place for future references.
DISCLAIMER

SAFETY PRECAUTIONS
The following precautions are provided to prevent harm or injury to yourself and others.
Please make sure to thoroughly read, understand, and follow these precautions before using the
product.
If product is damaged, appears to be damaged, or malfunctions, contact DULYTEK customer service
at [email protected].
INSTRUCTION MANUAL: DW4000 PAGE 3
• Use this product only as described in this manual.
• Keep the equipment out of the reach of children at all times.
• Unplug the heat press from the electrical outlet and let it cool down com-
pletely before cleaning, performing maintenance, or repair.
• DO NOT immerse the press, its power cord, and plugs in water or any
other liquid.
• DO NOT place the product on or near a hot gas or electric burner, heated
oven, or any other heat source.
• DO NOT operate the product with a damaged cord or plug.
• DO NOT leave any cords near a heat source. It can deform the cord or
meltitsinsulationcausingelectricalshockorre.
• Always insert the power plug all the way in.
• DO NOT handle a power plug with wet hands.
• When unplugging a power cord, grasp and pull with the plub instead of
the cord.
• DO NOT scratch, cut, twist, excessively bend, or tie the cord or put a
heavy object on it.
• DO NOT let the power cord drape over the countertop or tabletop, where
it can be accidentally tripped over or pulled on.
• DO NOT connect too many power plugs to the same power outlet.
• DO NOT operate the product after the appliance malfunctions or is
dropped or damaged in any way.
• DO NOT cover the press with a cloth. Doing so may trap heat within and
causere.
WARNING: Follow the warnings below. Otherwise, death or serious
injuries may occur.
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved

SAFETY PRECAUTIONS (continued)
INSTRUCTION MANUAL: DW4000 PAGE 4
• Remove dust around the plug and power cord with a dry cloth. If the sur-
ruoundingisdusty,humid,oroily,short-circuitmayoccur,causingare.
• DO NOT remove the machine cover.
• DONOTdisassemblethepressormakeanymodicationstotheequip-
ment.
HANDLING PRECAUTIONS
• The press must be operated on a hard, level surface, away from its
edges to prevent accidental tipping over.
• Work area must be kept clean, tidy, and free of obstructions to the press
moving parts.
• Alwaysattachthepowercordtothepressrst,thenplugitintothewall
outlet.
• To unplug the press, turn OFF all controls and switches, only then re-
move the plug from the outlet.
• DO NOT touch the press’s hot surfaces. Use heat-resistant gloves or
tools. Care must be exercised as burns can occur from touching platens.
• Keep your hands and other body parts away from the press moving parts
to prevent injury.
• Thispresscomeswithapowercordthattsintoastandardhousehold
3-prongoutlet(110V).DONOTattempttousetheequipmentwithatwo-
prong electrical cord or any other way without proper grounding.
• Contact DULYTEK if the equipment does not start or if smoke or unusual
odors are detected.
• Always turn the machine OFF and unplug it when done using.
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved

UNPACKING
INSTRUCTION MANUAL: DW4000 PAGE 5
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
WARNING: Keep the packaging materials (cardboard, foam, plastic
bags, etc.) out of the reach of children to prevent accidental choking,
su󰀨ocation, strangulation, and other injury.
Preserve the shipping carton. DO NOT discard or disassemble the shipping
box. It is designed to hold the weight of the product and should be used in
case you need to return the equipment for repair or warranty maintenance in
thefuture.DONOTattempttoshipthepressinadi󰀨erentcontainer.
UNPACKING
PRECAUTIONS
Before starting, please make sure that the following items are included with
your press machine. If anything is missing, contact DULYTEK.
1. DULYTEK DW4000 Heat Press;
2. Wheel;
3. Wheel Handle;
4. Screw;
5. Rubber mallet;
6. AC Power Cord;
7. Instruction Manual.
ITEM
CHECKLIST
The following items are recommended for pressing rosin oil:
1. Teabaglters;
2. Parchment paper sheets.
RECOMMENDED
PARTS
1. Placetheboxonalarge,sturdy,atsurface.
2. Open the box and remove the instruction manual and all parts that came
with the press.
3. Remove the packaging material and carefully lift the press out of the box.
4. Remove any protective or promotional labels from the press and other
parts if applicable.
5. Examine the heat press after unpacking for any damage. If found one,
take a picture and contact DULYTEK at [email protected] immediately.
UNPACKING
INSTRUCTIONS

GETTING FAMILIAR
INSTRUCTION MANUAL: DW4000 PAGE 6
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
DW4000 PRESS
PARTS,
FEATURES, AND
CONTROLS
Timer Button
Press Handle
Bottom Platen
Temperature
Control Panel
.
.
.
.
.
E
.
A
C
K
Top Platen
Temperature
and Timer
Control Panel
F
Bottom Platen
Axle
B
.
D
Top Platen
Wheel
.
G
Wheel Handle
H
Screw
.
I
.
Rubber Mallet
J
.

GETTING FAMILIAR
INSTRUCTION MANUAL: DW4000 PAGE 7
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
DW4000 PRESS
PARTS,
FEATURES, AND
CONTROLS
(continued)
ON/OFF Switch
AC Power Cord
Socket
..
L
M
1. Makesurethepressstandsonaatsturdycountertop.
2. Insert the wheel onto the axle making sure its groove aligns with
the axle ridge.
3. Use the enclosed rubber mallet to gently hammer the wheel in place.
4. Thread the long screw through the the wheel handle into the
wheel(asshownonthepage6).
5. Tighten the screw by hand.
ASSEMBLY INSTRUCTIONS
ASSEMBLY
G F
H
G
I
I
J

OPERATING INSTRUCTIONS
INSTRUCTION MANUAL: DW4000 PAGE 8
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
PREPARING
AND STARTING
THE PRESS
1. Prepare materials you wish to press.
2. Insert the AC cord that came with the product into the press AC power
cordsocketandthenplugitsotherendintoanelectricaloutlet(110V).
3. Flip the ON/OFF switch to turn the press on. The control panels
and light up.
M
SETTING
CONTROL
PANELS
The press comes with two control panels, and .
The top platen temperature is set using the control panel , and the bot-
tom platen temperature - the control panel . Both control panels allow you
to set temperature either in Fahrenheit or Celsius degree. The press timer is
set using the control panel . Please follow the steps below to record the
desired press settings:
1. PressSETbuttonontherstcontrolpanel(Figure1)togetintothetem-
peraturesettingmode.Youshouldnowsee“P-1”onthedisplay(Figure
2).
2. Press UP or DOWN buttons to select the desired temperature (Figure
3). The selected temperature is shown in green on the second line of the
display.
Tip: Enter the temperature either in °F or °C; you will be able to select the
temperature scale later.
EK
E
K
E
Figure 1 Figure 2 Figure 3
PressSETbuttonagain(Figure4)togointothepresstimersettings
mode.Now,youshouldsee“P-2”onthedisplay(Figure5).
3.
E
K
L

OPERATING INSTRUCTIONS (continued)
INSTRUCTION MANUAL: DW4000 PAGE 9
PressUPorDOWNbuttonstoselectthedesiredtimeinseconds(Figure
6)ORskip this step altogether and proceed to the step 5 if you are set-
ting the control panel .
PressSETbuttonagain(Figure7)togointothetemperaturescaleselec-
tionmode.Now,youshouldsee“P-3”onthedisplay(Figure8).
Tip: Depending on your machine’s default settings, you may either see
“F” or “C” on the second line of the display, indicating the currently se-
lectedtemperaturescale(°F or °C).ThecorrespondingLEDindicator,°F
or °C, will also be lit.
Press UP or DOWN buttons to select either °F or °C(Figure9)ORskip
thisstepifyouaresatisedwiththecurrentselection.
SETTING
CONTROL
PANELS
(continued)
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
4.
5.
6.
K
Figure 4 Figure 5 Figure 6
Figure 7 Figure 8 Figure 9

OPERATING INSTRUCTIONS (continued)
INSTRUCTION MANUAL: DW4000 PAGE 10
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
SETTING
CONTROL
PANELS
(continued)
PressSETbuttonagain(Figure10)torecordallcontrolpanel’ssettings.
Repeat the steps 1 to 7 on the remaining control panel.
7.
8.
Figure 10 Figure 11 Figure 12
PRESSING 1. Waituntilbothplatensheatuptothedesiredtemperature(s).Tip:Digits
on the upper line of the control panel displays show the current tempera-
ture of the corresponding platen, and numbers on the bottom line - the
set temperature. The HEAT LED indicators will be lit while the press is
heatingtheplatens(Figure11).Onceheatingisnished,theindicators
areturnedo󰀨,andthetemperaturesshownonbothlinesshouldbethe
same.
2. Place the material you wish to press in the center of the bottom platen .
3. Turn the wheel clockwise using the wheel handle to raise the bottom
platen and continue rotating it until the maximum pressure is reached.
4. Leto󰀨thewheelhandle.Themaximumreachedpressurewillbe
maintained.
5. Press the timer button to start the timer. The control panel starts
displaying the countdown.
6. Wait until the countdown ends and the press beeps. The TIMER indicator
lightsup(Figure12).
7. Pressthetimerbuttonagaintoturno󰀨thetimer.TheTIMERindicator
turnso󰀨,andthebeepingstops.
8. Rotate the wheel counterclockwise using the wheel handle to release
the press.
9. Remove the pressed material using heat resistant gloves or tools and
exercising extreme caution.
H
C
E
H
C
D
H
D

OPERATING INSTRUCTIONS (continued)
INSTRUCTION MANUAL: DW4000 PAGE 11
1. Turno󰀨thepressmachinebyippingON/OFFswitchwhendone
pressing.
2. Unplug and then disconnect the AC power cord from the press.
3. Wait until the press cools down completely to store it.
TURNING OFF
THE PRESS
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
CALIBRATING
TEMPERATURE
CONTROLS
(optional)
Calibrating a control panel should be done if the actual temperature shown
on its screen deviates from the set temperature after heating is done. Please
followthestepsbelowtocalibrateandproof-readthea󰀨ectedtemperature
control:
1. Press DOWN button for 5 seconds to enter into Temperature Collation
mode(Figure13).TheONLEDindicatorwilllightup(Figure14).
2. Wait for approximately 4 to 5 minutes. The temperature control will re-
calibrateitselfandadjusttothesetvalues(Figure15).
Figure 13 Figure 14 Figure 15
M

TECHNICAL SPECIFICATIONS
INSTRUCTION MANUAL: DW4000 PAGE 12
Dulytek Equipment
www.dulytek.com Email: [email protected]
© 2018 Dulytek
All rights reserved
PARAMETER SPECIFICATIONS
Model DW4000
Press Force 4000 lb / 2 Ton
Power 500 W
Current 4.5 A
Voltage 110V
Frequency 50 Hz
Dual Heating Plates Yes
Platen Size 4 x 2 inch / 100 x 50 mm
Temperature Range up to 750 °F / 399 °C
Temperature Scale Fahrenheit / Celcius
Timer up to 999 seconds
Dimensions 17.9 x 10 x 10 inch / 45.5 x 25.5 x 25.5 cm
Weight 42 lbs / 19 kg
Package Dimensions 20.7 x 12.8 x 12.8 inch / 52.5 x 32.5 x 32.5 cm
Package Weight 46.3 lbs / 21 kg
Certications CE / RoHS