Dunelm 30149781 User manual

DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set
the standard for quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves,
please don’t hesitate in contacting us on 08451 656565 where our team will be very
keen to understand what has gone wrong and, more importantly, put it right.
DEAR CUSTOMER
The next step…
There is no need to feel daunted by the number of parts and ttings in front of you, we have
compiled this straight forward, step-by-step guide to make sure that assembling your furniture
is as easy as 1, 2, 3.
Before you begin, we advise that you check that you have everything you need to get started.
TOP TIP
Find a space to spread these out across the oor before you begin
assembling them. Lay each panel down in position, ready to build.
It is recommended that two people assemble this product together.
The full list of furniture parts, xtures and ttings, as well as the tools you will need for assembly,
can be found on pages 2, 3 and 4 of this manual.
TOP TIP
Identify all of the ttings, make sure that you have them all prepared
and familiarise yourself with each component, to make things easier
when you are putting it all together.
Safety and Care Advice
IMPORTANT - The rst step you need to take is to ensure your safety!
Please take the time to read and understand these instructions before assembling your
furniture.
Keep children and animals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrapping materials away from children to avoid danger of suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Make sure that you allow enough space to move around when assembling your furniture.

Panels - plan view
Panel -
exploded view
Parts & Fittings for Soho TV Bench (30149781 / 30149736)
2
1
2
3
4
5
6
6
7
8
9
10
10
11
11
12
12
13
1Top panel(103x40cm) 2Bottom panel(103x40cm)
3Left side panel
(36x39.9cm)
4Right side panel
(36x39.9cm)
5Divider panel
(36x36cm)
9

3
A
6Shelfx2 (48.1x36cm)
9Left drawer side x2
(35x14cm)
10 Right drawer side x2
(35x14cm)
11 Drawer back panelx2
(43x14cm)
12 Drawer bottom x2
(44x34.8cm)
13 Back panel (98.7x37cm)
7Left drawer front
(48.5x17.7cm)
8Right drawer front
(48.5x17.7cm)
Fittings
30mm Connecting bolt x14
B
67mm Connecting bolt x2
C
15mm Locking cam x18
D
Cap x6
E
8mm Wooden dowel x20
F
6mm Wooden dowel x4
G
28mm Connecting bolt x8
H
13mm Locking cam x8
I
12mm Screw x12
J
15mm Screw x28
K
30mm Screw x8
L
50mm Screw x2

Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 08451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
Note: Recommend putting panel
on carpet to avoid scratch.
Cross slot screwdiver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
over tightening xings .
4
2
1
18mm Screw x6
M
Rear panel connector x6
N
Allen key x1
O
Leg x4
P
P1
P1
P1
P1
P1
x 4
J
2
J
P
J
J
P2
350mm Runner x4
Q

5
3
5
4
2
E
E
E
E
C
C
C
A
A
A
A
C
C
C
E
E
E
E
P1
P1
P1
P1
P2
P2
P2
P2
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Screw connecting
bolts as far as shown
Do not over tighten.
Slot
Outlet
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Screw connecting
bolts as far as shown
Do not over tighten.
Slot
Outlet
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
C
C3
4

6
6
8
7
Q1
Q2
QQ
Q
C
C
C
C
C
C
E
E
E
E
E
E
E
E
x 2
x 4
5
6
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
Slot
Outlet
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Slot
Outlet

7
9
11
10
4
5
5
Q1
Q1
Q1
Q1
3
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
JJ
JJJ
JJ
J
JJJ
Q1
Q1
JJJ

8
12
13
6
3
4
C
56
B
Note: Recommend putting panel
on carpet to avoid scratch.
Note: Recommend putting panel
on carpet to avoid scratch.
Front edge
Front edge

9
14
15
2
C
L
L
O
A
A
A
A
2
Screw connecting
bolts as far as shown
Do not over tighten.

10
16
18
17
Screw connecting
bolts as far as shown
Do not over tighten.
Note: Recommend putting panel
on carpet to avoid scratch.
13
1
A
A
A
A
A
A
1