Dunelm Soho 4 Drawer Chest Technical specifications

PRODUCT DESCRIPTION
Soho 4 Drawer Chest, 90x40x95cm, high gloss PU finish White.

straight forward, step-by-step guide to make sure that assembling your furniture is as easy as 1,2,3.
Before you begin, weadvise thatyou check that you have everything you need to get started.
DEAR CUSTOMER
Thank you for purchasing your new piece of furniture from Dunelm.
We put a lot of effort in the design and construction of our products to ensure they set the standard for
quality, durability and ease of assembly.
If for any reason you feel we haven’t lived up to the high standards we set ourselves, please don’t
hesitate in contacting us on 03451 656565 where our team willbe very keen to understand what has
gone wrong and, more importantly, put it right.
The Next Step...
TOP TIP
Lay each panel down on a clean and level area, ideally in the room of intended use, ensuring there is
enough room to manoeuvre around the item. It is recommended that two people assemble this
product together.
TOP TIP
component, to make things easier when you are puttingit all together.
The full list of furniture parts, xtures and ttings, as well as the tools you will needfor assembly can be found
on page2, 3 and 4 of this manual.
Safety and Care Advice
IMPORTANT-
Please take the time to read and understand these instructionsbefore assembling your furniture.
Please keep these instructions for future reference.
Keep children andanimals away from the assembly area.
This furniture contains small parts that could cause choking if swallowed.
Keep all plastic wrappingmaterials away from babies and children to avoid dangerof suffocation.
Ensure that all packaging is disposed of carefully and responsibly.
Two peoplemay be required for the assembly of this product.
Once items are part or fully assembled they are not returnable unless faulty.
This item is not for outdoor use– unless stated otherwise.
to the wall, to prevent a child from accidentally pulling furniture over.
Furniture can be dangerous if incorrectlyinstalled. Assembly should be carried out by a competent
person. No liabilitywill be accepted for damage or injury caused byincorrectlyinstalled or
assembled furniture.
1

Panels - plan view
Panel -
exploded view
Parts & Fittings for Soho 4 Drawer Chest (30213106)
2
1
2
3
4
7
7
7
7
12
14
13
1Top panel(90x40cm) 2Bottom panel(90x40cm)
3Left side panel
(85x39.9cm)
4Right side panel
(85x39.9cm)
6Back rail
(84.7x7.6cm)
5Front rail
(84.7x7.6cm)
6510
11
8
8
8
8
9

3
b
A
3
B C
D E F
G H I
JK
Plastic Bracket x4
L
340mm Plastic Cable Tie x2
15mm Screw x68

Note: Please place panel on soft surface
like a carpet to avoid scratches.
Cross slot screwdiver Hammer Tape measure
Tools required
The use of power tools to assemble the product is not recommended due to the risk of
over tightening ÿxings .
Before you start
Check the pack and make sure you have all the parts listed above. If not, contact the
helpline on 03451 656565 who will be able to help you.
When you are ready and sure that you have the right tools to hand, you will need plenty
of space and a clean dry area for assembly.
Ready?
Follow this step-by-step guide
4
2
1
350mm Runner x8
M
Leg x4
N
28mm Connecting bolt x4
O
13mm Locking cam x4
P
N1
N1
N1
N1
N1
x 4
F
2
F
N
F
F
N2

5
3
5
4
2
M1
M2
F F F
3
M1
M1
F
F
F
F
D
D
D
D
B
B
A
M
M
N1
N1
N1
N1
N2
N2
N2
N2
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Screw connecting
bolts as far as shown
Do not over tighten.
Slot
Outlet
Note: Please place panel on a soft surface
like a carpet to avoid scratches.
Note: Please place panel on a soft surface
like a carpet to avoid scratches.
This end to the front edge
of the panel
x8
A
front edge
Bottom edge

6
6
7
B
B
D
B
D
B
D
D
Fully insert locking
Hit wooden dowel
gently by hammer.
Do not strike
cams on the boards,
the slot always points
to the outlet of holes.
Slot
Outlet
A
F
F
F
F
FFF
D
D
4
M1
M1
M1
M1
D
D
B
B
A
Fully insert locking
cams on the boards,
the slot always points
to the outlet of holes.
Screw connecting
bolts as far as shown
Do not over tighten.
Slot
Outlet
Note: Please place panel on a soft surface
like a carpet to avoid scratches.
This end to the front edge
of the panel
Front edge
Top edge
5
6

7
8
13
14
3
4
4
3
B
B
C
5
6
9
+
-
Note: Please place panel on a soft surface
like a carpet to avoid scratches.
Fit the panels together with help.
Fit the panels together with help.

8
10
11
A
A
A
J
2
E
E
E
E
3
4
Back edge
Screw connecting
bolts as far as shown
Do not over tighten.
Note: Please place panel on a soft surface
like a carpet to avoid scratches.
Fit the panels together with help.
1
A
F
F
KF
F
K

9
12
13
H
H
H
H
H
H
1
4
I
H
I
I
I
I
3
B
B
C
XX=YY
+
-
Note: Maintain the cabinet
alignment when fixing .
H
Fit the panels together with help.
13
14
Two people required
to turn over the unit
carefully.
Ensure cabinet is in square before
fitting back panel