Dunelm Luna Assembly instructions

KIT CONTENT
Please note that this is the minimum kit content. For wider width
blinds, there will be additional brackets, screws and wall plugs.
TOOLS REQUIRED
Take care when using the tools. Wear gloves and eye protection.
CARE ADVICE
Wipe clean only
Roman Blind Fitting Guide
Thank you for purchasing this product. Please read the instructions and warning
carefully before use to ensure safe and satisfactory operation of this product.
Keep these instructions for future reference.
The safety clips or cleats must be positioned high enough to be out of reach of
small children. In all cases the distance from the floor to the bottom of the chord
and cleats must be at least 1.5 m. The head rail shall not be installed less than 1.5m from the floor.
All safety clips for blinds need to be fixed to a solid surface using a screw
and fixing suitable for the wall or surface material. These items should not be glued.
Small Parts can present a choking hazard if accidently swallowed.
Keep small parts away from young children.
We do not recommend that roman blinds are cut to size.
Ensure that all wall plugs and screws provided are suitable for your type of wall/window.
If in doubt, consult a professional.
Blind with fitted head rail x1
Pencil
Screws x 6
Ruler/tape measure Drill
Wall plugs x 6 Fixing Brackets x 2
LOCK
UNLOCK
Safety Device
(Cleat)
Young children can be strangled by loops in pull cords,
chains, tapes and inner cords that operate the product.
To avoid strangulation and entanglement, keep cords out of
the reach of young children.
Cords may become wrapped around a child’s neck. Move
beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and
create a loop.
WARNING
OPERATING THE BLIND
Raise: Pull down on the cord to raise
the blind to your desired height.
Unlock: Unwind the cord
from the cleat and pull
the cord to the left.
Lower: Once unlocked, the blind
should lower freely.
Lock: Pull the cord to
the right and secure
the cord onto the
cleat.

FITTING THE CHILD SAFETY DEVICE
(CLEAT)
The safety device (cleat) must be installed
as close to the head rail as possible and no
less than 1.5m from the floor.
Children can strangle if this safety device
is not installed. Always use this device
to keep cords or chains out of reach of
children.
Ensure all cords are fully wrapped around
the safety device provided (cleat).
Whenever the blind is not being operated.
There must not be any length of cord
available for a small child to wrap around
their neck.
CORD COLLECTOR CARE
If the cords become detatched, simply
press back into position.
Do not put the cords back in a twisted
position and never allow the cords to
become twisted when in use.
The chord collectors are designed to snap.
Do not remove the cord collector to
prevent child strangulation.
PRESS TO
CLOSE
CHILD SAFETY BREAK AWAY
At the back of your roman blind, the cords
attach to the fabric using clips. We take
the safety and well-being of children very
seriously so these clips also double up as a
child-safety feature. They will detach when
they are put under too much strain to prevent
the risk of strangulation. If they become
detached accidently during use of your blind,
these can be easily clipped back into place to
allow operation of the cords.
FITTING THE BRACKETS
FITTING THE BLIND
TOP MOUNT SIDE MOUNT
1. Making sure the swing arm on the bracket is
in the unlock position, then place the head rail
onto brackets so the outer lip of the head rail is
resting on the two projections.
2. Turn the swing arm on the bracket to the locked
position to secure the head rail to the bracket.
3. Gently pull back the fabric from
underneath the swing arm to
conceal from view.
SIDE
MOUNT
TOP
MOUNT
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
The brackets can be fixed top or side mounted
as shown. Place the blind bracket at least 8cm
inside from the end of the head rail. Mark screw
holes then screw in place the brackets. For
large blinds that require three brackets, the
third bracket should be placed in between the
two other brackets.
The brackets can be fixed inside or outside
your window recess. A top mount is used to fix
inside to the ‘ceiling’ of the window recess and
the side mount outside onto the window frame
or wall as shown.