Dustbane Hurricane 450 XTT User manual

Les Produits Dustbane Ltée, 25 pl. Pickering, Ottawa, ON K1G 5P4 •Tél : [phone] Fax : [phone] www.dustbane.ca
Hurricane 450 XTT
Guide rapide
Ce guide est destiné pour une consultation rapide seulement et ne constitue pas un remplacement au
guide d’utilisation et de remplacement. Avant d’utiliser cette machine, veuillez lire le guide d’utilisation et
d’entretien contenu dans l’emballage de la machine et suivez toutes les instructions.
PRÉPARATION ET OPÉRATION
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
1
4
6
2
5
7
3
Ajouter de l’eau et un produit chimique dans le
réservoir.
Tirez sur le levier de la raclette
pour l’abaisser.
Tournez la valve manuellement pour ajuster
le niveau de l’eau.
Mettre en marche.
Appuyez une fois pour allumer ou
éteindre l’eau.
Tirez sur le levier pour régler l’angle
de la poignée.
Tirez sur le levier pour activer le lavage.
8
This guide is intended for quick consultation only and does not replace the user and maintenance manual.
Before using the machine, read the user and maintenance manual contained in the machine’s packaging thoroughly and strictly follow all the
instructions.
PREPARATION & OPERATION
CT45 B Quick guide
1
6
2 3
9
5
7 8
PLDC02099
ON
AUTO
ECO
ECO
CHEM
H
2
O
+
> 3”
Appuyez une fois pour
mettre en marche ou
arrêter le moteur de la
brosse ou de l’aspirateur.
Appuyez et maintenez le
bouton de la brosse ou
de l’aspirateur pendant 3
secondes pour activer ou
désactiver le mode ECO.
Lorsque le mode ECO est activé, la lumière
de la brosse et de l’aspirateur clignote en
continu. Le mode ECO réduit la puissance
du moteur de 20 % pour diminuer la
consommation de la batterie.

REMPLACEMENT DES LAMES DE LA RACLETTE ATTACHEZ/RELÂCHEZ L’ENTRAÎNEMENT
Ouvrez le clip (Réf. 1).
Retirez les deux dispositifs de retenues de la lame (Réf. 2)
en les poussant vers l’extérieur et extraire la lame. Retirez la lame.
Réutilisez la même lame en inversant le bord en contact avec
le plancher jusqu’à ce que les quatre bords soient usés
ou remplacez-la par une nouvelle lame en la xant sur les vis
sur le corps de la raclette.
Repositionnez les deux dispositifs de pression de la lame
en centrant la partie la plus large du corps de la raclette
sur les fentes des pièces de xation, puis poussez les dispositifs
de pression de la lame vers l’intérieur.
Fermez le crochet à nouveau.
Replacez la raclette sur son support, en suivant les instructions décrites
précédemment.
Placez la brosse sous la tête, au centre (auto-récureuse à brosse
unique), placez les brosses sous la tête des deux côtés (auto-récuresue
à double brosse), mettez la machine en marche.
Appuyez sur l’interrupteur ON-OFF, une fois après le démarrage, la
machine libère la xation de la brosse. Le bouton n’est activé que
lorsque toutes les fonctions sont désactivées (moteur d’aspiration et
brosses).
Ref. 1 Ref. 2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
ENTRETIEN QUOTIDIEN
Nettoyez le réservoir d’eau sale. Assurez-vous que le sceau extérieur
des couvercles est propre et non
endommagé. Remplacez-le si
nécessaire.
Assurez-vous que le ltre de sortie
du détergent est propre et exempt
de débris.
Assurez-vous que les brosses/
tampon d’entraînement sont
propres et non usés. Remplacez-les
si nécessaire.
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
Assurez-vous que la raclette est
propre et que les lames ne sont pas
usées.
POUR CHARGER LES
BATTERIES
Branchez le chargeur autonome
dans le port de charge rouge
pour charger les batteries s’il
n’est pas équipé d’un chargeur
de bord.
REMARQUE : n’arrêtez jamais la
charge avant la n du cycle (feu
vert).
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•rest the brush on the oor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank oat
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet lter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the oor until all four edges are worn out, or replace with a new blade, tting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
Les Produits Dustbane Ltée, 25 pl. Pickering, Ottawa, ON K1G 5P4 •Tél : [phone] Fax : [phone] www.dustbane.ca