Dux DYNAMIC 19 User manual

DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2013.
Printed 2019.10.01
dux.com
2
DUX DYNAMIC 19
QUEEN/CAL.KING/152/160/180
ASSEMBLY INSTRUCTIONS
DUX, DUXIANA and DUX Pascal-systems are registered
trademark owed by Dux Design AB 2012.
Printed 2021.02.01
dux.com

dux.com DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
1
HARDWARE TOOLS NEEDED
Torx T30
(included)
Spanner 17mm or
adjustable wrench
(not included)
ASSEMBLING
I. PUT THE BEDS UP-SIDE-DOWN
Put the beds up-side-down on the oor
like the illustration.
The castors are mounted.
II. CONNECT THE CABLES
Attach the loose end of the cable to
the motor on the other bed base.
III. CONNECT THE BASES
Connect the bases with the middle
castor brackets.
×8 Felt
protection
×8 Floor
protection
Connecting plate
×2 Retainer bar
Hand control
×1 Middle
castor bracket

DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
dux.com dux.com DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
32
IV. TURN THE BED BASES BACK AROUND
AND CLOSE TOGETHER
Place the bed bases close together.
V. RAISE THE HEAD- AND FOOT-END
Plug the motors into the outlets.
Raise the head- and foot-end
to the maximum height.
VI. MOUNT THE CONNECTIONPLATES
AAt the head-end of the bed, remove
3 of 4 screws leaving the second
from the right below.
Loosen the remaining screw so that the
connection plate can slide between
the bed and the screw.
BAttach the connection plate with
the rst screw on the left. Rotate the
connection plate so the slot goes
over the screw.
CAdd the rest of the screws and tighten.
Repeat at the foot-end.
A B C
VII. MOUNT THE RETAINER BAR
While the head- and foot-ends are
raised, mount the retainer bar.
Remove the screws at the foot-end
and use them to fasten the
retainer bar to the bed.
VIII. ADD THE COVER STRIP
Add the cover strip to conceal the split
between the two panels
at the head- and foot-ends.
IX. LOWER THE BED
AND ADD THE SPRINGTOP
Lower the bed to the original at position
and add the springtop with
the split at the head-end of the bed.

DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
dux.com dux.com DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
54
DUX PASCAL-SYSTEM
CONFIGURE PASCAL-SYSTEM
ASSEMBLING
The Pascal System consists of three or six
interchangeable spring cassettes of
varying densities and tension.
Designed to provide three support zones –
shoulders, hips, legs – each cassette
is selected to match your body size
and weight for individually
customized comfort.
Common conguration is as follows:
SOFT – at the head, allowing your
shoulders to sink into the bed.
MEDIUM – in the middle, allowing hips
to sink down in the bed.
FIRM – at the foot, allowing some
elevation for your legs and feet.
X. OPEN THE BED
Open the bed and fold the top over.
XI. ARRANGE THE CASSETTES
Arrange the cassettes according to your
preference.
FIRM MEDIUM SOFT
XII. FOLD THE TOP BACK OVER
Fold the top back over and zip the
bed closed.
CONSUMER CAUTION
Do not sit on the head- or foot-end while
adjusting the bed.
THE HAND CONTROL
The motor comes with two 9V batteries. The batteries are used to lower the ends to their
original at position in the case of a power failure. (Test batteries often)
NOTE: The bed cannot be raised with only battery power.
head end up head end down
both head and
foot end up
both head and
foot end down
foot end up foot end down

DUX, DUXIANA and DUX Pascal-systems are registered trademark owed by Dux Design AB 2012.
Printed 2021.02.01
dux.com6
TROUBLE SHOOTING
PROBLEM
Lift motors do not work at all.
POSSIBLE CAUSE AND CORRECTION
Power at wall outlet may be out; reset circuit breaker.
Power cord may be unplugged; plug in cord.
Hand control batteries are low; replace batteries.
PROBLEM
Head or foot section will not go all way down.
POSSIBLE CAUSE AND CORRECTION
Head or foot section may have an obstruction.
Move the bed to the up position, then remove the obstruction.
If the problem persists, contact Customer Service.
PROBLEM
Head or foot end will not go up or starts and stops intermittently.
POSSIBLE CAUSE AND CORRECTION
Contact the DUXIANA store or a DUX reseller.
All replacements and service should be performed by a DUX authorized service dealer.