
DVI-TPS-TX90_RX90-QSG-01 / August.20124 1
Maximum Cable Lengths
Resolution Clock Freq. CAT-5e CAT-5e (1) CAT-6A (2) CAT-6A (1)(2)
1024x768 @60Hz 65.00 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m)
1280x720p @60Hz 73.84 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m)
1920x1080i @60Hz 74.25 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m)
1280x1024 @60Hz 108.00 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m)
1920x1080p @60Hz 148.50 MHz 328.1 ft. (100 m) 492.1 ft. (150 m) 393.7 ft. (120 m) 557.7 ft. (170 m)
1920x1200 @60Hz 152.90 MHz 328.1 ft. (100 m) N/A 393.7 ft. (120 m) N/A
1600x1200 @60Hz 162.00 MHz 328.1 ft. (100 m) N/A 393.7 ft. (120 m) N/A
Note 1: With Long Reach rmware installed. This rmware supports pixel clock frequencies up to 148.5 MHz.
Please contact DVIGear technical support or your dealer to change or upgrade device rmware.
Note 2: CAT6A S/FTP (550 MHz) cable must be used to achieve these distances.
Installation
WARNING: Ethernet ports are designed to connect to 10/100 Ethernet products. Do not connect
Ethernet appliances to TPS IN or TPS OUT ports as it may result in damage to the equipment.
1. Set the switch on the front panel to the Normal position.
2. Connect a CAT-X twisted pair cable to the TPS OUT on the transmitter unit.
3. Connect the other end of the CAT-X twisted pair cable to the TPS IN on the receiver unit.
4. Connect an HDMI signal source to the HDMI IN port on the transmitter unit.
5. Connect an HDMI display device (e.g. projector) to the HDMI OUT on the receiver unit.
6. To use the bi-directional pass-through data lines, connect desired devices to the transmitter
and receiver units. See examples in table(3) below.
7. Connect the supplied External AC Power Adapter to either unit. The other unit will
automatically receive power over the twisted pair cable connected between the TPS ports.
Ethernet Use LAN cables to connect an Ethernet device (e.g. switch) to the Ethernet port on the Transmitter unit
and a network device (e.g. projector) to the Ethernet port on the Receiver unit.
RS-232 Use serial cables to connect a controller unit (e.g. touch panel) to the RS-232 port on the Transmitter unit,
and serial controlled device (e.g. projector) to the RS-232 port on the Receiver unit.
Infra-Red Connect the supplied IR Transmitter to the IR OUT port of the transmitter unit.
Connect the supplied IR Receiver to the IR IN port on the Receiver unit.
Note 3: Examples of optional devices that are supported over the MultiPort TPS twisted pair link.
Introduction
DVIGear’s MultiPort TPS Extender supports long-range extension of HDMI (v1.4) signals over a single CAT-X
twisted pair (TP) cable at distances of up to 180 meters (590 ft.). These units also support bi-directional
RS-232, Infra-Red, 10/100 BaseT Ethernet, and PoE over the same twisted pair link.
Serial cable
LAN
TPS connection
CAT-X up to 180m
HDMI
cable
HD Projector
Projection screen
DVI-TPS-RX90
Remote powered
IR cable
IR Receiver
12V DC
Power Adaptor
LAN
HDMI cable
Ethernet switch
DVI-TPS-TX90
IR cable
Serial
cable Touch panel
Blu-Ray or DVD Player
Internet
LAN
IR Transmitter
Typical Application
DVI-TPS-TX90
DVI-TPS-RX90
MultiPort TPS ExtenderQuick Start Guide
MultiPort TPS Extender: DVI-TPS-TX90 and DVI-TPS-RX90