DVIGear WILDCAT DVI-7570 User manual

Your Digital Connectivity Experts
User Guide
4K HDMI CAT6 Extender Set
DVI-7570

TABLE OF CONTENTS
SECTION PAGE
PRODUCT SAFETY ....................................1
PRODUCT LIABILITY...................................1
1.0 INTRODUCTION ...................................2
2.0 SPECIFICATIONS ..................................3
3.0 PACKAGE CONTENTS ..............................5
4.0 CONNECTING THE HARDWARE......................5
5.0 OPERATING THE UNIT..............................9
6.0 TROUBLESHOOTING ..............................10
7.0 LIMITED WARRANTY ..............................11
8.0 REGULATORY COMPLIANCE .......................11

-1-
WARNING – Product Safety
1. Do not dismantle the product housing or modify the printed circuit board
module as this may result in electrical shock or burn.
2. Do not attempt to service this product yourself as opening or removing the
product housing may expose you to dangerous voltages or other hazards.
Refer all servicing to qualied service personnel.
3. Keep this product away from liquids. Spills into the product housing may
result in re, electrical shock, or equipment damage. If liquid spills into the
housing, unplug the product immediately. Have the product checked by a
qualied service engineer before using it again.
4. Place the product in an even and stable location. If the product falls or is
dropped, it may cause an injury and/or malfunction.
5. Avoid exposing the product to extreme temperatures or to high humidity
levels as this may result in damage to the product.
6. Only use the supplied External AC Power Adapter. The use of other power
adapters may cause this product to fail or may cause a re.
7. Do not twist or exert excessive force on the ends of the connected cables
as this can cause them to malfunction. Take precaution to ensure that all
connected cables are not forced to bend beyond their minimum bend radius.
Product Liability
Every effort has been made to ensure that this product is free of defects.
DVIGear cannot be held liable for the use of this product or for any direct or
indirect consequential damages arising from its use. It is the responsibility of
the users of this product to check that it is suitable for their requirements and
that it is installed correctly.
DVIGear, Inc. is the owner of numerous trademarks, both registered and
unregistered, including without limitation, the following marks: DVIGEAR®,
DISPLAYNET®, DISPLAYNET SERVER®, DISPLAYNET MANAGER®, N/AV
Design®, and HYPERLIGHT®.
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing Administrator,
Inc. All other third-party trademarks used herein are the properties of their
respective owners.
© 2021 DVIGear, Inc. All rights are reserved. No part of this manual may be
reproduced or transmitted by any form or means, electronic or mechanical,
including photocopying, recording or by any information storage or retrieval
system, without the prior written consent of DVIGear.

-2-
1.0 INTRODUCTION
DVIGear’s Wildcat™ DVI-7570 is the rst in a new generation of value-focused
HDMI extenders. They employ visually lossless compression that allows
resolutions of 3840 x 2160 /60p (4:4:4) to be extended as far as 30 meters (98 ft.)
over a single CAT6A cable. Resolutions up to 3840 x 2160 /30p (4:4:4) can be
extended to 70 meters (230 ft.).
This extender includes a buffered HDMI Loop Output for a local HDMI display on
the transmitter unit. The receiver unit includes de-embedded Analog and Digital
(TOSLINK) audio outputs to facilitate connections to an external audio system.
The DVI-7570 supports HDMI 4K /60p, is HDCP 2.2 compliant and supports
bi-directional Power-over-Cable, giving integrators and system designers
the exibility to power the extender set at either end of the signal chain. The
extenders occupy a minimal amount of space and can easily be concealed
thanks to an ultra-compact metal case, which includes all required mounting
hardware for a seamless, low-prole installation.
These features, together with the Wildcat Extender’s exceptional performance,
make it the ideal solution for cost-sensitive applications that demand high quality
HDMI signal distribution.
1.1 Features
The DVI-7570 offers several exceptional features:
• Supports HDMI 4K /60p, HDCP 1.4 and 2.2 compliant
• Supports resolutions up to 3840x2160 /60p (4:4:4) with visually
lossless compression
• Extends HDMI and IR over a single CAT6A cable
• Maximum extension distances:
3840 x 2160 /60p: 98 ft. (30 m)
3840 x 2160 /30p: 230 ft. (70 m)
• Bi-directional Power-over-Cable (POC)
• Buffered HDMI Loop Output on DVI-7570-TX
• Analog and Digital (TOSLINK) De-embedded Audio Output on DVI-7570-RX
• Ultra-compact, low-prole case for easy concealment
• Locking DC power connectors for added security and reliability
• Mounting hardware included

-3-
2.0 SPECIFICATIONS
Supported AV Signals
Video HDMI 4K /60p, DVI 1.0
HDCP HDCP 1.4 and HDCP 2.2
EDID Automatic EDID pass-through from connected display to source
Embedded Audio Supports pass-through of embedded HDMI audio, including LPCM
2.0/2.1/5.1/6.1/7.1, and HBR Bitstream formats
De-Embedded Audio
Analog Audio Output: Supports Stereo Linear PCM Audio up to
24-bit / 192 kHz
Optical S/PDIF Output: Supports Stereo Linear PCM Audio up to
24-bit / 192 kHz and Bitstream formats
IR Control Supports IR pass-through from RX to TX unit
Connections / Indicators
CAT Port 1 ea. shielded RJ45 female connector with LED Power and Signal
indicators
HDMI Input / HDMI Output DVI-7570-TX 2 ea. 19-pin female HDMI connectors for HDMI In and HDMI Out
DVI-7570-RX 1 ea. 19-pin female HDMI connector for HDMI Out
IR Control DVI-7570-TX 1 ea. IR OUT: 3.5mm Mini-Jack
DVI-7570-RX 1 ea. IR IN: 3.5mm Mini-Jack
Analog Stereo Audio DVI-7570-RX 1 ea. Analog Stereo Audio Out: 3.5mm Mini-Jack
Digital Audio DVI-7570-RX 1 ea. S/PDIF Audio Out: TOSLINK Optical Connector
Service Port Micro USB Female
DC Power 1 ea. 5.5 mm / 2.0 mm female screw-locking connector
Performance
Supported Video
Resolutions(1)
Up to 4K /60p with 8-bit color (4:4:4)
Up to 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0)
Supported Video Formats RGB / YCbCr 4:4:4, YCbCr 4:2:2/4:2:0, YUV 4:4:4
Supported PC Resolutions(1) Up to 3840x2160 / 60 Hz
Maximum Pixel Clock Freq.(1) Supports pixel clock rates up to 600 MHz
Maximum Video Bit Rate(1) Supports digital signal bit rates up to 6.0 Gbps./color, 18.0 Gbps. total
Video Signal Latency 6x Lines Total (3x Lines on TX and 3x Lines on RX)
Built-in ESD Protection Human body model: ±8KV (air-gap discharge) and ±4KV (contact discharge)
Recommended CAT Cable CAT6A S/FTP (500 MHz) AWG 23, or CAT7 (Europe); Compliant with TIA/EIA-
568B termination standard
Maximum Cable Distance
4K /60p: up to 98 ft. (30 meters) using CAT6A S/FTP (500 MHz)
AWG 23 cable
4K /30p: up to 230 ft. (70 meters) using CAT6A S/FTP (500 MHz)
AWG 23 cable
HDMI Input Cable
Equalization
Supports DVIGear’s HR™ Series HDMI with cable lengths up to 5 meters at
4K /60p resolution

-4-
2.1 Specications (Continued)
Power
Typical Power Consumption 3.84 watts total
Power Extension Bi-directional power over CAT6A cable
External AC Power Adapter Input: 100-240VAC, 50-60Hz
Output: +12VDC @ 1.0A
Mechanical
Construction Heavy-duty steel enclosure with jet black nish
Dimensions (H x W x D) Each Unit: 0.72" x 2.42" x 3.47" (18.3 x 61.4 x 88.2 mm)
Weight DVI-7570-TX: 5.64 oz (160 grams)
DVI-7570-RX: 5.47 oz (155 grams)
Environmental
Operating Temp. (Environment) +32° to +104°F (0° to +40°C)
Typical Case Temperature Tx Unit: 103.1°F (39.5°C); Rx Unit: 92.5°F (33.6°C)
Storage Temp. (Environment) -4° to +158°F (-20° to +70°C)
Operating / Storage Humidity 10% to 90% (non-condensing)
Regulatory Approvals
TX / RX Units FCC, CE, RoHS
External AC Power Adapter CE, UL, C-UL, CEC, DOFT, GS, PSE, CCC, KCC, CB, TUV, RoHS, WEEE, S,
RCM, Class II
Warranty
Limited Warranty 3 Years Parts and Labor
Model Numbers
DVI-7570 4K HDMI CAT6 Extender Set
DVI-7570-TX 4K HDMI CAT6 Transmitter
DVI-7570-RX 4K HDMI CAT6 Receiver
Accessories Included
1x External AC Power Adapter (per set)
1x IR Transmitter
1x IR Receiver
4x Mounting Brackets
1x Quick Start Guide
Note 1: In most cases HDMI audio is not supported for resolutions between 1920x1080 and
3840x2160. For more information, please contact DVIGear Support.
Note 2: All specications are subject to change without notice.

-5-
2.2 Supported Resolutions
This product supports all standard resolutions up to and including 1920x1080,
as well as 3840x2160 /60p using visually lossless compression. Resolutions
that have a pixel clock rate of above 600 MHz are supported. Due to the
compression technology used, Audio is not supported for resolutions more than
1920x1080 and less than 3840x2160 – unless the pixel clock is less than 150 MHz.
3.0 PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make certain
the following items are contained in the shipping carton:
• 1x DVI-7570-TX 4K HDMI CAT6 Transmitter
• 1x DVI-7570-RX 4K HDMI CAT6 Receiver
• 1x User Guide
• 1x External AC Power Adapter (+12 VDC)
• 1x IR Transmitter
• 1x IR Receiver
• 4x Mounting Brackets with Screws
Note: Please retain the original packing material in case you need to return the unit. If you
nd any items are missing, contact your reseller or DVIGear immediately. Please have the
Model Number, Serial Number, and Invoice Number available for reference when you call.
4.0 CONNECTING THE HARDWARE
Please study the images below and become familiar with the signal inputs,
outputs, and the location of the power connector.
Transmitter Unit – Input View
1HDMI Output: female connector; connect to an HDMI or DVI display.
This is a buffered HDMI Loop Output for a local HDMI display.
2HDMI Input: female connector; connect to an HDMI or DVI source.
1
21

-6-
Transmitter Unit – Output View
1CAT Output: RJ-45 female connector. See warning below.
2Service Port: reserved for qualied technical personnel.
3IR OUT: connect IR transmitter to accept IR signal from Rx Unit and
output to a source device.
412 VDC Power Input: screw locking female connector for AC Power Adapter.
Receiver Unit – Input View
1CAT Input: RJ-45 female connector. See warning below.
2Service Port: reserved for qualied technical personnel.
3IR IN: connect IR receiver to send IR signal over CAT-X cable to Tx Unit.
412 VDC Power Input: screw locking female connector for AC Power Adapter.
Receiver Unit – Output View
1HDMI Output: female connector; connect to an HDMI or DVI display.
21
1
32
3
21
1
32
3
1
21
32

-7-
2SPDIF Output: female TOSLINK connector; connect to an audio receiver.
3Analog Stereo Line Out: female 3.5mm connector; connect to an
audio receiver.
WARNING 1: The CAT cable ports are designed to connect to compatible DVIGear Wildcat™
series products only. Do not connect any device to the CAT cable connector unless you are
sure it is compatible. Connecting incompatible devices with similar connectors may cause
harm to the devices.
WARNING 2: It is typical for the CAT cable receiver unit to operate at higher temperatures
than the transmitter unit. In order to ensure proper operation and long term reliability, care
must be taken to ensure airow is not restricted in any way.
4.1 System Set-up
This HDMI extension system consists of a Transmitter unit (DVI-7570-TX) and a
Receiver unit (DVI-7570-RX). To connect this system, rst remove power from
all devices (installing devices while powered may cause damage). Connect a
CAT6A twisted pair cable to the CAT OUT on the transmitter unit. Connect the
other end of the CAT6A twisted pair cable to the CAT IN on the receiver unit.
Connect an HDMI or DVI signal source to the HDMI IN port on the transmitter
IR Rx
IR Tx
POC Remote Power
3840 x 2160/60p: 30 meters (98 ft.)
3840 x 2160/30p: 70 meters (230 ft.)
CAT6A Cable Distance
4K Television
(or Projector)
Sound Bar
Blu-Ray Player
12 VDC Power
Adapter*
HDMI Input
HDMI Monitor Loop Output
HDMI Output
Audio Output
* AC Power Adapter can be installed on either the Tx or Rx unit and automatically powers both devices.
CAT6A Cable
IR Control
DVIGear HR™ HDMI Cable
Audio Output
Power Cable
DVI-7570-RX
(remotely powered by transmitter)
DVI-7570-TX

-8-
unit. Connect an HDMI or DVI display device (e.g. projector) to the HDMI OUT
on the receiver unit.
Additionally, the transmitter includes a buffered HDMI Loop Output for a local
HDMI display. Use of a High Speed HDMI®cable or High Speed HDMI to
DVI-D cable such as DVIGear’s High Resolution (HR™) Series is recommended.
Connect an HDMI or DVI display device (e.g. local monitor) to the HDMI OUT on
the transmitter unit.
The receiver features both a de-embedded Analog and a Digital (TOSLINK) audio
output to facilitate connections to an external audio system such as a sound bar
or speaker system.
Note: Proper operation of this product depends on the use of high quality cables. CAT6A
S/FTP (550 MHz) 23AWG twisted pair cable is recommended to maximize extension distances.
4.2 Power Connections and Bi-Directional Power over CAT Cable
The DVI-7570 is capable of being powered on either the transmitter or receiver
side, with the opposite side receiving its power over the CAT cable (POC). This
feature eliminates the need for a second external power supply at either the
receiver or transmitter.
For POC operation, connect the supplied AC Power Adapter to the 12 VDC
Power Input on either unit and then to a working AC power source. Once the
unit detects the POC compatible unit on the other side of the connection, it will
provide power over the CAT cable. If non-POC operation is desired, simply
connect the optional AC Power Adapter to the 12 VDC Power Input on both
units. In this case, the units will not supply power to each other.
Note: This product utilizes a locking DC power connector to prevent the power cable from
disengaging. Insert the DC plug into the power input jack on the rear panel, then gently rotate
the locking collar in the clockwise direction until it is secure. To remove the power connection,
simply unscrew the locking collar counter-clockwise and then extract the power cable.

-9-
4.3 Mounting Hardware
Each transmitter and receiver unit comes with a pair of mounting brackets to
facilitate installation on furniture or other surfaces. To afx each bracket to an
extender unit, align the two mounting holes of the plate with the holes on the
underside of the unit. Next, use the supplied screws to secure the bracket to the
case.
5.0 OPERATING THE UNIT
Once all connections have been made and power has been applied to all
components, this extension system should function immediately. This product
has no adjustments and does not require conguration.
Bottom View
Top View

6.0 TROUBLESHOOTING
WARNING 1: The CAT cable ports are designed to connect to compatible DVIGear Wildcat™
series products only. Do not connect any device to the CAT cable connector unless you are
sure it is compatible. Connecting incompatible devices with similar connectors may cause
harm to the devices.
WARNING 2: It is typical for the CAT cable receiver unit to operate at higher temperatures
than the transmitter unit. In order to ensure proper operation and long term reliability, care
must be taken to ensure airow is not restricted in any way.
If this unit does not appear to be functioning, make certain that the 12 VDC
power adapter is connected securely to a functioning AC power outlet and to
one of the units. Ensure that the Link LEDs on both TX and RX units are both lit.
If the system fails to display a signal, power OFF all devices and conrm that the
following connections are properly installed: the TX unit must be connected to
the source using the shortest possible high quality cable. The RX unit must be
connected to the display using the shortest possible high quality cable. Ensure
that the CAT cable between the TX and RX is of the highest quality possible and
within the allowable length noted on page 3. Verify that none of the cables used
show signs of damage and are not forced to bend beyond their minimum bend
radius.
If the IR connection is not functioning, verify that the IR Transmitter and IR
Receiver are connected in the correct conguration according to section 4.1
and that all connectors are securely seated.
Once all connections have been veried, power the display device on rst and
then the signal source. If the system still fails to display an image, check to
ensure that the HDMI or DVI signal source is compatible with the display by
making a direct connection between the two so as to bypass the extender pair.
If there is still no image, then there is a compatibility issue between the source
and the display that must be resolved.
If there are issues with audio dropouts, ensure that a compatible resolution is
being used. Refer to section 2.2 for more details
If the problem persists after trying the above suggestions, please contact your
dealer for additional assistance. If the dealer’s technical personnel are unable
to assist you, please contact DVIGear via telephone at 1.888.463.9927 (toll-free
for United States and Canada) or 1.770.421.6699. You may contact DVIGear by
e-mail at [e-mail].
-10-

7.0 LIMITED WARRANTY
LIMITED WARRANTY – Subject to the limitations stated below, DVIGear warrants
that this product will be free from defects in materials and workmanship for a
period of three (3) years from the date of purchase.
Should the product, in DVIGear’s opinion, prove defective within the warranty
period stated above, DVIGear, at its option, will repair or replace this product
without charge. Any defective parts replaced become the property of DVIGear.
This warranty does not apply to products that have been damaged due to accident,
unauthorized alterations, improper repair, modications, inadequate maintenance
and care, or use in any manner for which the product was not intended.
If repairs are necessary under this warranty policy, the original purchaser must
obtain a Return Authorization Number from DVIGear and return the product
freight prepaid to a location designated by DVIGear. After repairs are complete,
the product will be returned, freight prepaid.
The foregoing warranty is the sole and exclusive warranty given by DVIGear,
express or implied, and DVIGear disclaims all implied warranties, including but
not limited to implied warranties of merchantability or tness for a particular use.
LIMITATIONS – The liability of DVIGear with respect to any defective products
will be limited to the repair or replacement of such products. In no event shall
DVIGear be responsible or liable for any damage arising from the use of such
defective products, including but not limited to loss of use, revenue or prot,
whether such damages are direct, indirect, consequential or otherwise and
whether such damages are incurred by the reseller, end user, or any third party.
8.0 REGULATORY COMPLIANCE
This product is compliant with appropriate FCC, CE and RoHS rules and
regulations. The supplied AC Power Adapter is compliant with CE, UL, C-UL,
CEC, DOFT, GS, PSE, CCC, KCC, CB, TUV, RoHS, WEEE, S, RCM, Class II rules
and regulations.
-11-

Your Digital Connectivity Experts
www.dvigear.com
DVIGear, Inc.
1059 Triad Court, Suite 8
Marietta, Georgia USA 30062
Toll Free 888.463.9927
Phone [phone]
Fax [phone]
DVI-7570-UG-01 / September.2021