Dynasty Fireplaces EF58US Quick start guide

Homeowner’s
Installation Instructions&
Operating Manual
ELECTRIC HEATER WITH REMOTE CONTROL
Model: EF57US,EF58US,EF59US,EF60US
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR
MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELFAND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE.
WARNING! To reduce the risk of fire, electric shock, or personal
injury, read all the instructions before using this heater.

IMPORTANT INSTRUCTIONS
When using electrical appliances，basic precautions should always be followed to reduce the risk of
fire，electrical shock，and injury to persons including the following：
1. Read all instructions before using this appliance.
2. Do not use outdoors.
3. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
4. Children should be supervised to ensure that they do not play with the appliance.
5. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least
3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
6. Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating unattended.
7. Unplug power cord before servicing or moving the heater. Always unplug heater when not in
use.
8. Do not operate any heater with a damaged cord or after the heater malfunctions, has been
dropped or damaged in any manner. Return heater to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Never locate heater where it may fall into a bathtub or other water container.
10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like.
Arrange cord away from traffic area and where it will not be tripped over.
11. To disconnect heater, turn controls to off, then remove plug from outlet.
12. Connect to properly grounded outlets only.
13. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it
may cause an electric shock or fire or damage the heater. Do not block or tamper with the
heater in any manner while it is in operation.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline,
paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.
17. Where possible, avoid the use of extension cords because the extension cord may overheat
and cause a risk of fire.
18. This heater includes an overheat protection system that shuts off the heater when parts of the
heater are getting excessively hot. If the heater shuts off, immediately turn the heater OFF and
inspect for any objects, on or adjacent to the heater, which may cause high temperatures. DO
NOT OPERATE THE HEATER UNTIL IT IS RESET. To reset the heater, turn it OFF, unplug it
from the electrical outlet, and wait five to ten minutes for the unit to cool down before plugging it
back in and turning the heater on.
19. Make certain that the power source conforms to the electrical requirements of the heater.
20. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place
heater on soft surfaces, like a bed, where openings may become blocked.
21. A heater has hot and arcing or sparking parts inside. It must NOT be used in potentially
dangerous locations such as flammable, explosive, chemical-laden or wet atmosphere. This
heater is intended for use in general use only.
WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH THE SOLE MEANS OF
DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG
THE POWER CORD.
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
SAVE THESE INSTRUCTIONS

INSTALATION INSTRUCTION
TOOL REQUIRED
Magnetic Phillips Screw Driver
Unpacking the Electric Fireplace
WARNING! Do NOT use this Electric Fireplace if any part has been under water.
Immediately call a qualified service technician to inspect and to replace any part of
the electrical system if necessary. Keep plastic wrapping away from children.
●Open the packaging carefully and remove the foam.
●Remove and discard the plastic bag.
●Be responsible when handling the packing materials.
●Keep the original packaging for future transport and/or storage.
●Check all accessories are got before you keep the packing.
PARTS AND HARDWARE LIST
Fileplace engine
Title
Qty.
fireplace engine
1pc
remote control
1pc
battery
2pcs
instruction manual
1pc
screw ST4×8
6pcs(for all front)
2pcs(for TE3/TE4 only)
screw ST4×16
2pcs
fixing bracket
2pcs
PRODUCT MODEL units: ㎜
FIREPLACE
ENGINE
FRONT
SPEC
MODEL
MODEL
TE1
TE2
TE5
SIZE
33”
EF57US
860×755
EF57US + TE1-33
EF57US + TE2-33
EF57US + TE5-33
36”
EF58US
935×795
EF58US + TE1-36
EF58US + TE2-36
EF58US + TE5-36
40”
EF59US
1035×885
EF59US + TE1-40
EF59US + TE2-40
EF59US + TE5-40
42”
EF60US
1080×935
EF60US + TE1-42
EF60US + TE2-42
EF60US + TE5-42
units: ㎜
FIREPLACE
ENGINE
FRONT
SPEC
MODEL
MODEL
TE3 (STEEL)
TE4 (GLASS)
SIZE
33”
EF57US
935×795
EF57US + TE3-36
EF57US + TE4-36
36”
EF58US
1035×885
EF58US + TE3-40
EF58US + TE4-40
40”
EF59US
1080×935
EF59US + TE3-42
EF59US + TE4-42
Front
Title
Qty.
Front
1pc
Air flow plate
1pc

FIREPLACE ENGINE SIZE
D1
H3
W3
W1
W2
H1
H2
units: ㎜
model
OVER SIZE
FLAME view
OTHER SIZE
W1
H1
D1
W2
H2
W3
H3
EF57US
850
668
289
800
481
803
646
EF58US
925
708
289
875
521
878
686
EF59US
1025
798
289
975
611
978
776
EF60US
1060
828
339
1010
616
1013
806
MANTEL FRAMING SIZE
D2
H4
H5
W4
units: ㎜
W4
D2
H4
H5
TE3-36/TE4-36
838
300
655
44
TE3-40/TE4-40
914
300
695
69
TE3-42/TE4-42
1016
300
785
49
TE1-33/TE2-33/TE5-33
838
300
655
0
TE1-36/TE2-36/TE5-36
914
300
695
0
TE1-40/TE2-40/TE5-40
1016
300
785
0
TE1-42/TE2-42/TE5-42
1059
350
815
0

LOCATING YOUR ELECTRIC FIREPLACE
Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing
a location ensure that the general instructions are followed. For best results, install out of direct sunlight.
Power supply service must be either completed or placed within the electric fireplace prior to finishing to
avoid reconstruction.
WARNING ! Keep drapery and other furnishings at least 3ft /0.9m from the front and sides of the
electric fireplace.
Clearance to Combustibles
Sides ……………………………….. 0 in. (0 mm)
Floor ……………………………....
.
Top …………………………….……0 in. (0 mm)
Back ………………………………...0 in. (0 mm)
Installation:
1. With front TE1/TE2/TE5
W4
D2
H4
(10)
Fireplace
mantel
Wood
panel
Clip
Insert
Clip
H5
Fixing
bracket
Screw
ST4x8
1.1 Gently push the insert into the front of the mantel.
1.2 Fix the fixing bracket onto the fireplace
engine by 2pcs of ST4*8 screws.
Screw
ST4x16
Srcrew ST4x8 Airflow plate
1.3 Fix the insert with the mantel panel by 2pcs of
ST4*16 screws.
1.4 Fix the airflow onto the fireplace engine by
4pcs of ST4*8 screws.
TE4-36/TE4-36
TE3-40/TE4-40
TE3-42/TE4-42
Other Series
1.7in.(44mm)
2.7in.(69mm)
1.9in.(49mm)
0 in. (0 mm)

Pole
Magnet
1.5Install the front onto the insert by locating the pole on both sides well, and slightly push the trim
bottom to fit the engine by magnets. Installation is completed.
2. With front TE3/TE4
Pole
Screw ST4x8
2.1 Fix the insert into the mantel as step 1.2 & 1.3 & 1.4, locate the front onto the engine by the pole on
both sides and push down, then fix the trim by 2pcs of ST4*8 screws.
GROUNDING
Plug the power supply cord into a wall outlet (120Vac, 60Hz).The cord has a plug as shown at A.
You should follow as shown at the below:
Grounding methods
ELECTRICAL CONNECTION
A15 AMP, 120 Volt, The unit comes standard with 6 feet (1.8 m) three wire cord, exiting from the rear of
the fireplace. Plan the installation to avoid the use of an extension cord. Preferably, the fireplace will be
on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the
fuse to blow when the heater is in operation.

MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING.
DO NOT IMMERSE HEATER IN WATER!
Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning
your heater.
Light accumulated dust may be removed from the heater with a soft cloth or vacuum cleaner.
Wipe the exterior surfaces of the heater occasionally with a slightly damp cloth (not dripping
wet) using a solution of mild detergent and water. Dry the case thoroughly before operating the
heater.
Caution: Do not allow water to run into the interior of the heater as this could create a fire or
electric shock hazard.
The fan motor is factory lubricated for life and will not require further lubrication.
Store heater in a clean dry place when not in use.
Warning: Any other servicing needed must be performed by an authorized service representative.
Do not attempt to service the unit yourself.
OPERATING INSTRUCTION
This appliance can be operated by both remote control and manual button. Once the unit has been
properly connected
to an earthed electrical outlet, turn on the main power switch located on the left hand side of the
appliance. A beep should be heard when the power is first applied.
CAUTION! The unit’s power cord must be connected to a properly grounded and protected
120V outlet. Always use ground fault protection where required by the electrical code.
WARNING! Do not operate the unit if it is damaged or has malfunctioned. If you suspect the
unit is damaged, please call a qualified service technician to inspect and to replace any part
of the electrical system If necessary.
NOTE! To use both remote and manual function. As the main power switch must be in “ON”position.
●Operating by Manual Button
NOTE! The manual button on the fireplace unit is not provide you with all function control, and its
propose is to control some basic function when you lose the remote handset. Please use the remote
handset to carry out all functions.
FLAME HEATER
flame button
heater button
main power switch
Main power switch
The POWER switch supplies power to all of the functions of the fireplace. This switch must be in the
“ON” position for any of the functions including the remote to work.

Flame button
The fire has four flame effects, by pressing the flame effect button the unit will cycle through each effect.
Heater button
Press once turns 750W power on. (Pilot lights illuminated ●○)
Press again turns 1500W power on (Pilot lights illuminated ●●)
Press third time turns heater off. (Pilot lights illuminated ○○)
To Reset the Heater
Your heater includes a protection system that shuts off the heater if it overheats for any reason:
1) Turn unit to off.
2) Unplug unit wait 5 minutes.
3) Plug in and turn on.
●Remote control functions
Note:
The fireplace Main Power Switch must be switched ON in order for the Remote Control to function.
In order to protect the product not becoming too hot, there is 8s delay when turning on the heater; also
there is 8s delay when turning off the heater fan.
Make sure the battery are installed properly in the remote control.
The effective range of the remote control is up to 4 meters or 13 feet.
WARRANTY
In the unlikely event of a problem occurring due to a manufacturing fault within 24 months from the date
of purchase of the appliance it will be repaired or replaced free of charge.
This warranty does not cover consumable items such as the bulbs and fuses which have a limited
lifespan.
If a problem should occur, the nature of the problem together with the date of a purchase should be
immediately reported to the retailer that the appliance was purchased from. Proof of purchase will be
required so the original invoice should be retained.
ICON
TITLE
FUNCTION
POWER
Press once turns appliance on. Press again turns appliance off.
FLAME
The fire has four flame effects, by pressing the flame effect button
the unit will cycle through each effect.
HEATER
Press once turns 750W power on. (Pilot lights illuminated ●○)
Press again turns 1500W power on (Pilot lights illuminated ●●)
Press third time turns heater off. (Pilot lights illuminated ○○)
TEMP
Digital display shows the TEMP setting 23°C (default), with 14
settings circle from “OFF”, “16°C”to ”28°C”.
The TEMP will increase by 1°C up to 28°C when pressed each
time.
By pressing the TEMP for 3S, the digital display can show
between °C and °F.
16-28°C corresponds to 61-82°F.
TIMER
Cycles from OFF, 0.5H, 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H, to 9H.
BACK
LIGHT
By pressing the downlight button the unit will cycle
through two effect it including OFF and ON setting.

Dynasty Fireplaces
Unit 10 - 3071 No. 5 Road, Richmond, BC V6X 2T4 Canada
Tel: [phone] / Toll free: 1-877-521-1009
Fax: [phone]
Http: www.dynastyfireplaces.com
Email: [e-mail]