Dynasty Fireplaces Cascade Series Parts list manual

DYNASTY FIREPLACES
Cascade Series
Linear smart electric fireplace • Cheminée électrique linéaire intelligente
Installation Instructions & Operating Manual
Manuel d’Installation & d’Utilisation
Models / Modèles
DY-BTX42 | DY-BTX52 | DY-BTX64 | DY-BTX74 | DY-BTX82 | DY-BTX100
10-3071 No. 5 Road, Richmond, BC V6X 2T4 Canada
PHONE: [phone] | [e-mail] | dynastyfireplaces.com
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
OPERATE, OR MAINTAIN THIS PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE.
LIRE ATTENTIVEMENT AVANT D’ESSAYER D’ASSEMBLER, D’INSTALLER,
D’UTILISER, OU D’ENTRETENIR CE PRODUIT.
PROTÉGEZ-VOUS ET VOTRE ENTOURAGE EN RESPECTANT LES
CONSIGNES DE SÉCURITÉ. LE NON-RESPECT DE CES CONSIGNES
POURRAIT CAUSER DES BLESSURES CORPORELLES ET / OU DES
DOMMAGES MATÉRIELS.
WARNING: To reduce risk of fire, electrical
shock, or personal injury, read and
understand all instructions, including safety
information before plugging in and
operating.
AVERTISSEMENT: Pour réduire le risque
d’incendie, de décharge électrique, ou de
blessures corporelles, lisez et assurez-vous
de comprendre toutes les instructions, y
compris les consignes de sécurité, avant de
brancher et d’utiliser cet appareil.

- 2 -
SAFETY INFORMATION
• Read all instructions before using this heater!
• This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater
and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the heater is left operating and unattended.
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has
been dropped or damaged in any manner. Discard heater or return to authorized service facility
for examination and/or repair.
• DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or
similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord
away from traffic area, and where it will not be tripped over.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause electric shock or fire, or damage the heater.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could
cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline,
paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
• ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord
or relocatable power tap (outlet/power strip).
• DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the
bed and be ignited by the heater.
• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could
fall into a bathtub or pool, become damp, or come in contact with water.
• AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
• NEVER hang this unit on a wall directly below an electrical outlet.
• NEVER permanently install in a recessed area of the wall. This may result in blocked air flow,
overheating, or fire.
• ALWAYS secure to wall framing before use.

- 3 -
SAFETY INFORMATION
• WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES.
• This product is not intended to be a primary heat source. It is for supplemental heat only.
• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
• NEVER modify this heater. Doing so could result in personal injury or property damage.
Modification of this fireplace completely voids all warranties.
• ALWAYS turn this heater off before unplugging it from the outlet.
• ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
• NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
• ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.A
• ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this
heater trips the circuit breaker, unplug all other appliances on the same circuit before the
next use. Avoid plugging other appliances into the same circuit as this heater.
• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing within
the outlet that could cause the outlet to overheat or catch fire.
• ALWAYScheck your heater cord and plug connections with each use!
1. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or
loose plugs can cause the outlet to overheat.
2. Heaters draw more current than small appliances. Overheating may occur even
if it has not occurred with the use of other appliances.
3. During use check frequently to see if the plug outlet or faceplate is HOT! If the
outlet or faceplate is HOT, discontinue use immediately and have a qualified
electrician inspect and/or replace the faulty outlets.
This heater has a polarized plug (one blade is wider than the other). As a safety feature to
reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.

- 4 -
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS (all models) FLAME ONLY OPERATION
WiFi OPERATION
• Connect on 2.4 GHz network only
WiFi 802.11 b/n/g
PRODUCT DIMENSIONS
DY-BTX42
DY-BTX52
DY-BTX64
25 W
32 W
34 W
INPUT VOLTAGE
120V AC, 60 Hz
CABLE LENGTH
72", 2.0m
MAX. POWER
CONSUMPTION
1500W
HEAT OUTPUT
1500W Nominal
1500W Max.
750W Min.
DY-BTX74
DY-BTX82
DY-BTX100
41 W
46 W
51 W
Model
A
B
C
D
E
F
G
DY-BTX 42
1079 mm
514 mm
165 mm
946 mm
381 mm
480 mm
956 mm
42 ½in.
20 ¼in.
6 ½in.
37 ¼in.
15 in.
18 ⅞in.
37 ⅝in.
DY-BTX 52
1333 mm
514 mm
165 mm
1200 mm
381 mm
480 mm
1210 mm
52 ½in.
20 ¼in.
6 ½in.
47 ¼in.
15 in.
18 ⅞in.
47 ⅝in.
DY-BTX 64
1638 mm
514 mm
165 mm
1505 mm
381 mm
480 mm
1514 mm
64 ½in.
20 ¼in.
6 ½in.
59 ¼in.
15 in.
18 ⅞in.
59 ⅝in.
DY-BTX 74
1892 mm
514 mm
165 mm
1759 mm
381 mm
480 mm
1768 mm
74 ½in.
20 ¼in.
6 ½in.
69 ¼in.
15 in.
18 ⅞in.
69 ⅝in.
DY-BTX 82
2096 mm
514 mm
165 mm
1962 mm
381 mm
480 mm
1972 mm
82 ½in.
20 ¼in.
6 ½in.
77 ¼in.
15 in.
18 ⅞in.
77 ⅝in.
DY-BTX 100
2553 mm
514 mm
165 mm
2421 mm
381 mm
480 mm
2432 mm
100 ½in.
20 ¼in.
6 ½in.
95 ¼in.
15 in.
18 ⅞in.
95 ⅝in.

- 5 -
PACKAGE CONTENTS
PLEASE REMOVE ACCESSORIES AND MANUAL BEFORE DISCARDING
PACKAGING
For warranty, parts, or product support, please visit our site at:
support.dynastyfireplaces.com
Contact us at: [e-mail]
INSTALLATION
LOCATING YOUR ELECTRIC FIREPLACE
Your new electric fireplace may be installed virtually anywhere in your home. However,
when choosing a location, ensure that the general instructions are followed. For best
results, install out of direct sunlight. Power supply service must be either completed or
placed within the electric fireplace prior to finish to avoid reconstruction.
MINIMUM CLEARANCE TO COMBUSTIBLES
FRONT
BACK
SIDES
TOP
BOTTOM
36" / 0.9m
0"
0"
0"
0"

- 6 -
WARNING! Keep drapery and other furnishings at least 3ft /0.9m from the front of the
electric fireplace.
FRAMING & INSTALLATION
Note: Ensure that you leave adequate room to remove and replace the front screen or
optional front.
Framing Dimensions
Model
A
B
Depth
DY-BTX 42
495 mm
984 mm
172 mm
19 ½in.
38 ¾in.
6 ¾in.
DY-BTX 52
495 mm
1238 mm
172 mm
19 ½in.
48 ¾in.
6 ¾in.
DY-BTX 64
495 mm
1543 mm
172 mm
19 ½in.
60 ¾in.
6 ¾in.
DY-BTX 74
495 mm
1797 mm
172 mm
19 ½in.
70 ¾in.
6 ¾in.
DY-BTX 82
495 mm
1994 mm
172 mm
19 ½in.
78 ½in.
6 ¾in.
DY-BTX 100
495 mm
2451 mm
172 mm
19 ½in.
96 ½in.
6 ¾in.

- 7 -
Framing Procedure
1. Build frame according to framing dimensions on previous page and ensure power
source is available
2. Remove front glass and trim piece, and set aside (refer to page 8 for instructions)
3. It is recommended to install the fireplace after finishing the wall to ensure the side
brackets sits flush with the wall finishing
Top View
4. After wall has been finished, place fireplace into wall framing and use framing screws to
secure the side brackets to wall. Then install front glass and trim piece.
NOTE: There are four rubber feet on the bottom of the fireplace that can be
removed before installation

- 8 -
PLACING MEDIA ON FLAME BED
Removing Front Glass
1. Locate the heater louver in the middle of the fireplace underneath the trim. Remove the
heater louver by removing the two screws holding it in place, then remove front trim
piece
2. Loosen and remove the two front glass clips under the trim. You can use the clips to
hook on and remove the glass. Set glass aside in secure location.

- 9 -
3. For crystal effect:
Carefully spread the small clear crystal stones across the fuel bed.
Then evenly arrange the larger crystal stones starting along the inset window ledge at
the front of the firebox.
For log effect:
Carefully spread the small clear and semi-painted crystal stones across the fuel bed.
Arrange the logs and place the small semi-painted and clear crystal stones in between
the log layout.
HARDWIRE OPTION
Plug-in
You may run the power cord out of the framed wall opening to an existing
outlet or install an outlet on a nearby wall stud within the wall). If the cord is not
long enough to reach the outlet, a grounded extension cord minimum AWG
No. 14 wiring and rated to a minimum or 1875 watts may be used.
Hard-wire
A qualified electrician may remove the cord connection and wire the appliance
directly to the house hold wiring. The appliance must be electrically connected
and grounded in accordance with local codes.

- 10 -
FIREPLACE REPAIR GUIDES
For full detailed instructions and step-by-step guides on how to
repair and service the fireplace, including repair and replacement of
parts such as LED lights, motor, heater, etc, please visit our support
website at:
support.dynastyfireplace.com
SERVICEABLE PARTS LIST
NOTE:
*PARTS WITH “XX” AT THE END DENOTES THE SKU OF THE FIREPLACE. FOR EXAMPLE, A DY-BTX64
WILL REPLACE THE “XX” WITH “64”
For parts, please contact your dealer, distributor, or point of
purchase and provide model number and serial number when
requesting service parts
ITEM
DESCRIPTION
PART NUMBER*
1
IR Receiver
DY-BTX-RCV
2
Flame Motor
DY-BTX-MTR
3
Main Control Board
DY-BTX-PCB-XX
4
Remote
DY-BTX-RMT
5
Crystal Media
DY-BTX-CRY-XX
6
Log Media
DY-BTX-LOG-XX
7
Heater
DY-BTX-HTR
8
Flame Bed LED
DY-BTX-FBL-XX
9
Flame LED
DY-BTX-FLD-XX
10
Flicker Rod
DY-BTX-FKR-XX
11
Flame Screen
DY-BTX-FMS-XX
12
Front Trim
DY-BTX-TRM-XX
13
Front Glass
DY-BTX-FGL-XX

- 11 -
OPERATION
This appliance can be operated by remote control and onboard buttons, however
onboard buttons have limited functions. A beep should be heard when the power is
first applied.
1. ONBOARD BUTTONS
The onboard buttons are located under the trim on the top left.
Press the Flame button to turn on/off the flame LED and cycle through flame
brightness levels High/Medium/Low.
Press the Heater button to turn on/off the heater and cycle through heat levels
High/Low. Heat level is indicated by the Heater Indicator light.
Red Indicator: High heat Indicator On: Heater timer is set
Blue Indicator: Low heat
Indicator Off: Heater off
2. WIFI CONFIGURATION
With the fireplace turned off (flame off, heater off) and supplied with
power, press and hold the Heater button for 5 seconds, then release. The
WiFi Indicator will begin flashing indicating the fireplace is ready for setup
in the Dynasty App.
The WiFi Indicator will remain on once connection to the app is successful.
For more information on WiFi setup, and connecting to voice-assistants
visit: support.dynastyfireplaces.com
Heater
Flame
Timer
Heater Indicator
WiFi Indicator

- 12 -
3. REMOTE CONTROL
In order to protect the product from becoming too hot, there is a 10s delay when
turning on the heater; also, there is a 10s delay when turning off the heater fan.
l Make sure the batteries are installed properly in the remote control.
l The effective range of the remote control is up to 4 meters or 13 feet.

- 13 -
OPERATION
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this
fireplace. Failure to do so could result in electric shock, fire, or personal
injury.
Cleaning
NEVER immerse in water or spray with water. Doing so could result in
electric shock, fire, or personal injury.
Metal:
l Buff using a soft cloth, slightly dampened with a mild cleaning solution if
needed.
l DO NOT use brass polish or household cleaners as these products will damage
the metal trim.
Glass:
l Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-
free cloth.
l NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Plastic:
l Wipe gently with a slightly damp cloth and a mild cleaning solution and warm
water.
l NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Vents:
l Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
l Clean the exterior of the fireplace with a slightly damp cloth or duster.

- 14 -
Maintenance
Risk of electric shock! DO NOT OPEN! No user-serviceable parts
inside!
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this fireplace.
Failure to do so could result in electric shock, fire, or personal injury.
Electrical and Moving Parts:
l The fan motors are lubricated at the factory and will not require lubrication.
l Electrical components are integrated in the fireplace and are not serviceable by
the consumer.
Storage:
l Store heater in a clean dry place when not in use.
Replacement parts:
l Use only replacement parts supplied by Dynasty Fireplaces. Use of any other
parts, or modifying the fireplace in any way, will void all warranties.
l If you’ve made a purchase through one of our retailers, contact them to order
parts, or contact [e-mail]
For full detailed instructions and step-by-step guides on how to
repair and service the fireplace, including repair and replacement of
internal parts such as LED lights, motor, heater, etc, please visit our
support website at:
support.dynastyfireplace.com

- 15 -
OPERATION
This product is inspected, tested and carefully packaged to minimize the chance of damage
during shipment. If a part within two years, or 24 months from the date of purchase proves to
be defective in material or fabrication under normal use, the part will be repaired or replaced.
Dynasty Fireplaces’ obligation under the warranty is to replace or repair defective parts at our
discretion. Any expenses or damage resulting from the installation, removal, or transportation
of the product will be the responsibility of the owner and are not covered by this warranty.
The owner assumes all other risks arising from the use or misuse of the product. The warranty
will be void if the product damage or failure is deemed by Dynasty to be caused by accident,
alteration, misuse, abuse, incorrect installation or removal, or connection to an incorrect
power source by the owner. Dynasty Fireplaces neither assumes, nor authorizes and person or
entity to assume for it any obligation or liability associated with its products.
Dynasty Fireplaces
10-3071 No. 5 Road
Richmond, BC Canada
V6X 2T4
Telephone: [phone]
Toll free: 1-877-521-1009
Website: dynastyfireplaces.com
Support: [e-mail]
Support Site: support.dynastyfireplaces.com