Dynasty Fireplaces Melody Series Parts list manual

DYNASTY FIREPLACES
Melody Series | Séries Melody
3-sided smart electric fireplace • Foyer électrique intelligent à 3 faces
Installation Instructions
& Operating Manual
Manuel d’Installation &
d’Utilisation
Models / Modèles
DY-BTS35 / DY-BTS40 / DY-BTS60
3231 No. 6 Road, Unit 127, Richmond, BC V6V 1P6 Canada
PHONE: [phone] | suppo[email protected] | dynastyfireplaces.com
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
OPERATE, OR MAINTAIN THIS PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE.
LIRE ATTENTIVEMENT AVANT D’ESSAYER D’ASSEMBLER, D’INSTALLER,
D’UTILISER, OU D’ENTRETENIR CE PRODUIT.
PROTÉGEZ-VOUS ET VOTRE ENTOURAGE EN RESPECTANT LES
CONSIGNES DE SÉCURITÉ. LE NON-RESPECT DE CES CONSIGNES
POURRAIT CAUSER DES BLESSURES CORPORELLES ET / OU DES
DOMMAGES MATÉRIELS.
WARNING: To reduce risk of fire, electrical
shock, or personal injury, read and
understand all instructions, including safety
information before plugging in and
operating.
AVERTISSEMENT: Pour réduire le risque
d’incendie, de décharge électrique, ou de
blessures corporelles, lisez et assurez-vous
de comprendre toutes les instructions, y
compris les consignes de sécurité, avant de
brancher et d’utiliser cet appareil.

© 2022 Dynasty Fireplaces | V 1.0.0
- 2 -
For setup guides, full product specs, and warranty
information, please visit us at:
support.dynastyfireplaces.com
Contact us:
[e-mail]
1-877-521-1009

© 2022 Dynasty Fireplaces | V 1.0.0
- 3 -
SAFETY INFORMATION
• Read all instructions before using this heater!
• This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater
and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever
the heater is left operating and unattended.
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has
been dropped or damaged in any manner. Discard heater or return to authorized service facility
for examination and/or repair.
• DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or
similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord
away from traffic area, and where it will not be tripped over.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause electric shock or fire, or damage the heater.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could
cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline,
paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
• ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord
or relocatable power tap (outlet/power strip).
• DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the
bed and be ignited by the heater.
• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could
fall into a bathtub or pool, become damp, or come in contact with water.
• AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
• NEVER hang this unit on a wall directly below an electrical outlet.
• NEVER permanently install in a recessed area of the wall. This may result in blocked air flow,
overheating, or fire.
• ALWAYS secure to wall framing before use.

© 2022 Dynasty Fireplaces | V 1.0.0
- 4 -
SAFETY INFORMATION
• WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES.
• This product is not intended to be a primary heat source. It is for supplemental heat only.
• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
• NEVER modify this heater. Doing so could result in personal injury or property damage.
Modification of this fireplace completely voids all warranties.
• ALWAYS turn this heater off before unplugging it from the outlet.
• ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
• NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
• ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
• ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this
heater trips the circuit breaker, unplug all other appliances on the same circuit before the
next use. Avoid plugging other appliances into the same circuit as this heater.
• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing within
the outlet that could cause the outlet to overheat or catch fire.
• ALWAYS check your heater cord and plug connections with each use!
1. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or
loose plugs can cause the outlet to overheat.
2. Heaters draw more current than small appliances. Overheating may occur even
if it has not occurred with the use of other appliances.
3. During use check frequently to see if the plug outlet or faceplate is HOT! If the
outlet or faceplate is HOT, discontinue use immediately and have a qualified
electrician inspect and/or replace the faulty outlets.
This heater has a polarized plug (one blade is wider than the other). As a safety feature to
reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.

© 2022 Dynasty Fireplaces | V 1.0.0
- 5 -
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
IC Statement:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.

© 2022 Dynasty Fireplaces | V 1.0.0
- 6 -
1. GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS (all models) FLAME ONLY OPERATION
AMBIENT LIGHTING
WiFi OPERATION
• Controlled via Dynasty app
• Connect on 2.4 GHz network only
WiFi 802.11 b/n/g
1.1 PRODUCT DIMENSIONS
Model
A
B
C
D
E
F
G
H
I
DY-BTS35
872 mm
840 mm
739 mm
506 mm
110 mm
325 mm
220 mm
315 mm
15 mm
34 ⅜in.
33 in.
29 in.
20 in.
4 ⅜in.
12 ¾#in.
8 ⅝in.
12 ⅜in.
½in.
DY-BTS40
1032 mm
1000 mm
633 mm
400 mm
110 mm
325 mm
220 mm
315 mm
15 mm
40 ⅝in.
39 ⅜in.
25 in.
15 ¾in.
4 ⅜in.
12 ¾#in.
8 ⅝in.
12 ⅜in.
½in.
DY-BTS60
1632 mm
1600 mm
633 mm
400 mm
110 mm
325 mm
220 mm
315 mm
15 mm
64 ¼in.
63 in.
25 in.
15 ¾in.
4 ⅜in.
12 ¾#in.
8 ⅝in.
12 ⅜in.
½in.
DY-BTS35
DY-BTS40
DY-BTS60
27 W
28 W
46 W
INPUT VOLTAGE
120V AC, 60 Hz
CABLE LENGTH
72", 1.8m
MAX. POWER
CONSUMPTION
1500W
HEAT OUTPUT
1500W Nominal
1500W Max.
750W Min.
DY-BTS35
DY-BTS40
DY-BTS60
17 W
25 W
26 W

© 2022 Dynasty Fireplaces | V 1.0.0
- 7 -
1.2 PACKAGE CONTENTS
PLEASE REMOVE ACCESSORIES AND MANUAL BEFORE DISCARDING PACKAGING
For warranty, parts, or product support, please visit our site at:
support.dynastyfireplaces.com
Contact us at: [e-mail]

© 2022 Dynasty Fireplaces | V 1.0.0
- 8 -
2. PREPARATION & FRAMING
2.1 LOCATING YOUR ELECTRIC FIREPLACE
Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a
location, ensure that the general instructions are followed. For best results, install out of direct sunlight.
Power supply service must be either completed or placed within the electric fireplace prior to finish to
avoid reconstruction.
MINIMUM CLEARANCE TO COMBUSTIBLES
FRONT
BACK
SIDES
TOP
BOTTOM
36" / 0.9m
0"
0"
0"
0"
WARNING! Keep drapery and other furnishings at least 3ft /0.9m from the front of the electric fireplace.
2.2 FRAMING & INSTALLATION
Note: Ensure that you leave adequate room to remove and replace the front screen or optional front.
Framing Dimensions
Model
W
H
Depth
DY-BTS60
1610 mm
643 mm
320 mm
63 ⅜in.
25 ⅜in.
12 ½in.
DY-BTS40
1010 mm
643 mm
320 mm
39 ¾#in.
25 ⅜in.
12 ½in.
DY-BTS35
850 mm
749 mm
320 mm
33 ½in.
29 ½in.
12 ½in.

© 2022 Dynasty Fireplaces | V 1.0.0
- 9 -
3. INSTALLATION
3.1 FIREPLACE CONFIGURATION
When unpacking the fireplace, the side plates have been fixed on the appliance.
Remove them if you want the appliance to be installed in a two-sided or three-sided
configuration.
Take out the edging strips and fix them to any side where the side panel has been
removed. This will create an edge for drywall or finishing materials.
The fireplace can be installed in 3 different configurations. The intended
configuration should be considered before installation:
1) Single-sided front configuration (front window visible only)
2) Two-sided configuration (front and one sided visible)
3) Three-sided configuration (front and sides visible)
NOTE:
1) Do not fix any edging strips for one
sided installation
2) For two-sided installation, fix the
edging strips ONLY to the side to be
exposed – DO NOT REMOVE THE
COVER PLATE OF THE UNEXPOSED
SIDE
3) For three-sided installation, fix the
edging strips to both sides

© 2022 Dynasty Fireplaces | V 1.0.0
- 10 -
Secure the edging strips with the eight ST4*8 screws already on the fireplace from the
side panels.
Before installing the fireplace into the wall enclosure, it is recommended that the
power is turned on and the appliance is operated to check function and that power
is supplied to the fireplace.
3.2 INSTALLATION
NOTE: Ensure that air can enter the vents on the underside and the top of the fireplace. The
fireplace is fitted with metal feet on the top and bottom. Do not block the top vents or
underside between the feet.
1. Build frame according to framing dimensions on Page 8 and ensure a power source is available.
It is recommended to install the fireplace after finishing the wall to ensure the side brackets sits
flush with the wall finishing.

© 2022 Dynasty Fireplaces | V 1.0.0
- 11 -
2. Push the appliance into the frame and fold out the brackets on the top and lower edge of this
appliance to secure it to the stud with (C) ST 4*40 Screws.
3. Cover the framing by drywall panels or your finishing of choice. The finishing material
can be used to cover the exposed metal areas on the sides and front of the appliance.

© 2022 Dynasty Fireplaces | V 1.0.0
- 12 -
3.3 PLACING MEDIA & REMOVING FRONT GLASS
1. Remove the front glass panel by removing the thumbscrews and fixing brackets and bolt,
and then remove the front glass by pulling forward and lifting out of position.
2. After removing the glass front panel, turn on the flame.

© 2022 Dynasty Fireplaces | V 1.0.0
- 13 -
3. You may see some groups of red lights on the bottom of back screen. These are
reflections of LED lights under the front edge of the fuel bed area. Place the black
glass ember components tightly against back glass.
4. Sprinkle vermiculite and the small clear crystals sprinkle it between the black glass
embers to cover the remaining visible sections of the fuel bed area.
5. Position the logs or large crystal pieces over the flame bed. Rearrange or create the
arrangement to your own liking. All the logs will fit onto the appliance, but can be left
off if desired.
6. Reinstall the front glass panel.
CRYSTAL MEDIA LOGS MEDIA

© 2022 Dynasty Fireplaces | V 1.0.0
- 14 -
3.4 POWER OPTIONS
Plug-in
You may run the power cord out of the framed wall opening to an existing outlet or
install an outlet on a nearby wall stud within the wall). If the cord is not long enough to
reach the outlet, a grounded extension cord minimum AWG No. 14 wiring and rated to
a minimum or 1875 watts may be used.
Hard-wire
A qualified electrician may remove the cord connection and wire the appliance directly
to the house hold wiring. The appliance must be electrically connected and grounded
in accordance with local codes.
3.5 FIREPLACE REPAIR GUIDES
For full detailed instructions and step-by-step guides on how to
repair and service the fireplace, including repair and replacement of
parts such as LED lights, motor, heater, etc., please visit our support
website at:
support.dynastyfireplace.com

© 2022 Dynasty Fireplaces | V 1.0.0
- 15 -
3.5 SERVICEABLE PARTS LIST
NOTE:
*PARTS WITH “XX” AT THE END DENOTES THE SKU OF THE FIREPLACE. FOR EXAMPLE, A DY-BTX64
WILL REPLACE THE “XX” WITH “64”
For parts, please contact your dealer, distributor, or point of
purchase and provide model number and serial number when
requesting service parts

© 2022 Dynasty Fireplaces | V 1.0.0
- 16 -
4 - OPERATION
This appliance can be operated by remote control and onboard buttons, however
onboard buttons have limited functions. A beep should be heard when the power is
first applied.
4.1 ONBOARD BUTTONS
The onboard buttons are located under the trim on the top left.
Press the STAND-BY button to turn on or off the electric fireplace. This will turn on the
flame LEDs and flame bed LEDs, and enable control of other functions
Press the FLAME button to turn on/off the flame LEDs.
Press the HEATER button to turn on/off the heater and cycle through heat levels
High/Low. Heat level is indicated by the Heater Indicator light in the middle of the
appliance.
Press once for low heat (Heater indicator ●○)
Press twice for high heat. (Heater indicator ●●)
Press three times to turn off heat (Heater indicator ○○)
Press the SPEED button to adjust the flickering speed of the flames. There are six total
settings for the flame speed.
Flame Speed
Flame
On/Off
Heater
WiFi Button

© 2022 Dynasty Fireplaces | V 1.0.0
- 17 -
4.2 WIFI CONFIGURATION
The Melody series is controllable via Dynasty Fireplaces’ own smartphone
app for Android and iOS. Download the Dynasty app, and signup for an
account with your email, and connect your fireplace. To download the app,
visit:
dynastyfireplaces.com/download
For more information on WiFi setup, and connecting to voice-assistants
visit: support.dynastyfireplaces.com
WIFI SETUP
NOTE: WiFi control and operation of the fireplace can only be done after an
account has been created, and the device has been linked to your account
1. Download the Dynasty app, follow the onscreen instructions to create an account.
Only an active email is required to create an account
2. With the fireplace in standby mode (flame and heater turned off, plugged into
power), press and hold the WiFi Button for 5 seconds until the flame bed flashes
red and makes a beeping sound.
3. Ensure the flame bed is blinking RED, then return to the app to complete setup
and link the fireplace to your account. The fireplace flame bed will flash GREEN for
a successful connection, and BLUE for an unsuccessful connection.
For more information on WiFi setup, and connecting to voice-assistants visit:
support.dynastyfireplaces.com

© 2022 Dynasty Fireplaces | V 1.0.0
- 18 -
4.3 REMOTE CONTROL

© 2022 Dynasty Fireplaces | V 1.0.0
- 19 -
5 - CLEANING & MAINTENANCE
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this
fireplace. Failure to do so could result in electric shock, fire, or personal
injury.
5.1 CLEANING
NEVER immerse in water or spray with water. Doing so could result in
electric shock, fire, or personal injury.
Metal:
l Buff using a soft cloth, slightly dampened with a mild cleaning solution if
needed.
l DO NOT use brass polish or household cleaners as these products will damage
the metal trim.
Glass:
l Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-
free cloth.
l NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Plastic:
l Wipe gently with a slightly damp cloth and a mild cleaning solution and warm
water.
l NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Vents:
l Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
l Clean the exterior of the fireplace with a slightly damp cloth or duster.

© 2022 Dynasty Fireplaces | V 1.0.0
- 20 -
5.2 MAINTENANCE
Risk of electric shock! DO NOT OPEN! No user-serviceable parts
inside!
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this fireplace.
Failure to do so could result in electric shock, fire, or personal injury.
Electrical and Moving Parts:
l The fan motors are lubricated at the factory and will not require lubrication.
l Electrical components are integrated in the fireplace and are not serviceable by
the consumer.
Storage:
l Store heater in a clean dry place when not in use.
Replacement parts:
l Use only replacement parts supplied by Dynasty Fireplaces. Use of any other
parts, or modifying the fireplace in any way, will void all warranties.
l If you’ve made a purchase through one of our retailers, contact them to order
parts, or contact sup[email protected]
For full detailed instructions and step-by-step guides on how to
repair and service the fireplace, including repair and replacement of
internal parts such as LED lights, motor, heater, etc., please visit our
support website at:
support.dynastyfireplace.com