Dynasty Fireplaces DY-BEF45 Quick start guide

Homeowner’s
Installation Instructions &
Operating Manual
Model: DY-BEF37 DY-BEF45 DY-BEF57
DY-BEF64 DY-BEF80
Please read the instructions carefully before installation or
use of this electric fire and retained for future reference.
Dynasty Fireplaces
#10-3071 No.5 Road, Richmond, BC V6X 2T4 Canada

2
Contents
Important safety information .........................................................................................3
Appliance data ..............................................................................................................5
Product dimension ........................................................................................................5
Packing list ....................................................................................................................6
Installation......................................................................................................................6
Operation ......................................................................................................................11
Care and maintenance .................................................................................................14
Warranty .......................................................................................................................15

3
IMPORTANT SAFETY INFORMATION!
WARNING
Read all instructions before using this heater!
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front
of the heater, and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating and unattended.
DO NOT operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater, or return to
authorized service facility for examination and/or repair.
DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs,
runners, or similar coverings. DO NOT route power cord under furniture or appliances.
Arrange power cord away from traffic area, and where it will not be tripped over.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as
this may cause electric shock or fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. Doing so
could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become
blocked.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where
gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an
extension cord or relocatable power tap (outlet/power strip).
DO NOT place the heater near a bed because objects such as pillows or blankets can fall
off the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location where the
heater could fall into a bathtub or pool, become damp, or come in contact with water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or
other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
NEVER hang this unit on a wall directly below an electrical outlet.
NEVER permanently install in a recessed area of the wall. This may result in blocked air
flow, overheating, or fire.
ALWAYS mount to wall bracket before use.
NEVER use a wall mount bracket from another manufacturer.

4
WARNING
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS
HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
For residential use only! NOT for commercial use! Any commercial or public use of
this heater voids all warranties, and could cause injury.
This product is not intended to be a primary heat source. It is for supplemental heat
only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric
shock!
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
NEVER modify this heater. Doing so could result in personal injury or property
damage. Modification of this fireplace completely voids all warranties.
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any assembly
or cleaning, or before relocating the electric fireplace.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become
wet.
ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If
this heater trips the circuit breaker, unplug all other appliances on the same circuit before
the next use. Avoid plugging other appliances into the same circuit as this heater.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing
within the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use!
a. MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs
can cause the outlet to overheat.
b. Heaters draw more current than small appliances. Overheating may occur even if it
has not occurred with the use of other appliances.
c. During use check frequently to see if the plug outlet or faceplate is HOT! If the outlet
or faceplate is HOT, discontinue use immediately and have a qualified electrician
inspect and/or replace the faulty outlets.
This heater has a polarized plug (one blade is wider than the
other). As a safety feature to reduce the risk of electrical shock,
this plug is intended to fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
SAVE THIS INSTRUCTION!

5
APPLIANCE DATA
Model No. EF206-210B (BEF37-80)
Supply Voltage AC 120V 60Hz
Heating Element 1500W
Mains Cable 1 x 2.0m (approx)
Maximum power consumption: 1500W
Power for flame effect:
EF206B
(BEF37)
EF207B
(BEF45)
EF208B
(BEF57)
EF209B
(BEF64)
EF210B
(BEF80)
9W+8W
10.4W+8W
15W+8W
17.2W+8W
26.7W+8W
Power for Fuel Bed:
EF206B(BEF37)
EF207B(BEF45)
EF208B(BEF57)
EF209B(BEF64)
EF210B(BEF80)
5.8W
5.8W
8.6W
8.6W
10.4W
Heat Output:
Nominal heat output (Pnom): 1500W
Minimum heat output(indicative) (Pmin): 750W
Maximum continuous heat output (Pmax): 1500W
Auxiliary Electricity Consumption:
At nominal heat output (elmax): 45.1W
At minimum heat output (elmin): 22.8W
In standby mode (elSB): 0.49W
PRODUCT DIMENSION
units: inch
MODEL
A
B
C
D
E
F
G
H
I
EF206B(BEF37)
36.69
8.27
22.05
35.43
14.96
2.24
0.79
33.62
13.19
EF207B(BEF45)
44.57
8.27
22.05
43.31
14.96
2.24
0.79
41.50
13.19
EF208B(BEF57)
56.38
8.27
22.05
55.12
14.96
2.24
0.79
53.31
13.19
EF209B(BEF64)
64.25
8.27
22.05
62.99
14.96
2.24
0.79
61.18
13.19
EF210B(BEF80)
80.00
8.27
22.05
78.74
14.96
2.24
0.79
76.93
13.19

6
INSTALLATION
LOCATING YOUR ELECTRIC FIREPLACE
Your new electric fireplace may be installed virtually anywhere in your home. However,
when choosing a location, ensure that the general instructions are followed. For best
results, install out of direct sunlight. Power supply service must be either completed or
placed within the electric fireplace prior to finish to avoid reconstruction.
WARNING ! Keep drapery and other furnishings at least 3ft /0.9m from the front of the
electric fireplace.
FRAMING
Note: Ensure that you leave adequate room to remove and replace the front
screen or optional front.
PACKING LIST
A - Fireplace (1)
B-Remote Control (1)
C-AAA Battery (2)
D-Small and Large
Crystal Stones (1 set)
E-Log (1 set)
F- ST 4*8 Metal Screws
(8)
G- Fixing Brackets (4)
H- ST 4*12 Metal Screws
(4)
I- Owner’s Manual (1)

7
Choose a fireplace location and frame as shown in figure 1. units: inch
MODEL
EF206B
(BEF37)
EF207B
(BEF45)
EF208B
(BEF57)
EF209B
(BEF64)
EF210B
(BEF80)
W
36.93
44.80
56.62
64.49
80.24
Figure 1
Take out the 4 fixing brackets and 8pcs ST4X8 screws to fix on the left and right
side panel of the unit.
Figure 2
Use 4 ST4*12 screws to fix the fireplace on the frame as shown in figure 3.

8
Figure 3
Take out the trim gently, take out the screw M5*12 on both sides, and use glass
hook to take out the glass carefully as shown in figure 4 and figure 5.
Figure 4

9
Figure 5
Set the fuel bed
For crystal effect:
Carefully spread the small clear crystal stones across the fuel bed.
Then evenly arrange the larger crystal stones along the inset window ledge at the front
of the firebox.
For log effect:
Arrange the logs. Below arrangement in the picture for your reference.
Place the small semi-painted and clear crystal stones in between the log layout.

10

11
The fireplace is packaged with a three prong plug installed for plug-in convenience.
Hard wiring the fireplace is also an option for any installation.
Plug in (you may run the power cord out of the framed wall opening to an
existing outlet or install an outlet on a nearby wall stud within the wall). If the
cord is not long enough to reach the outlet, a grounded extension cord minimum
AWG No. 14 wiring and rated to a minimum or 1875 watts may be used.
Hard wire the fireplace (recommended). A qualified electrician may remove the
cord connection, and wire the appliance directly to the house hold wiring. The
appliance must be electrically connected and grounded in accordance with local
codes.
Remove the 2 screws to release the cover of junction box.
Remove the cord connection.
Wire to a properly grounded, 120volt, 60Hz, 15 AMP circuit.
Ensure all junction block connections are tight.
Replace the cover and retaining screws.
OPERATION
This appliance can be operated by both remote control and manual button. Once the
unit has been properly connected to an earthed electrical outlet, turn on the main
switch. A beep should be heard when the power is first applied.
NOTE: To use both remote and manual functions, the main on/off switch must be
in ‘on’ position.
●Operating by Manual Button

12
NOTE：The flame will always on when the appliance is on.
Main power switch
The POWER switch supplies power to all of the functions of the fireplace. This switch must be
in the “ON” position for any of the functions including the remote to work.
Power button
By pressing the POWER button, turn the fireplace on when it is off or turn it off when it is on.
Flame button
By pressing the FLAME button, the unit will cycle through five flame effects.
Fuel bed button
By pressing the FUEL BED button to cycle through 14 fuel bed effects.
Heater button
Press once turns Fan on, and 8s later Low heat on. (Pilot lights illuminated ●○)
Press again turns on High heat. (Pilot lights illuminated ●●)
Press third time turns heat off. 8s later fan off (Pilot lights illuminated ○○)
There are 3 levels you can cycle through including the OFF setting.
To Reset the Heater
Your heater includes a protection system that shuts off the heater if it overheats for any reason:
1) Turn unit to off.
2) Unplug unit wait 5 minutes.
3) Plug in and turn on.
●Operating by Remote Handset
In order to protect the product from becoming too hot, there is a 8s delay when
turning on the heater; also there is a 8s delay when turning off the heater fan.
Make sure the batteries are installed properly in the remote control.
The effective range of the remote control is up to 4 meters or 13 feet.

13
Multifunction Infrared Remote Handset
BUTTON
FUNCTION
ACTION & INDICATION
ON/OFF
ON: Turns on.
Note:
All the functions are off in the standby mode,
it will memorize the working condition of flame
effect and heating.
OFF: Returns the unit to standby mode.
1. Press. The flame effect and the
remote control functions are enabled.
The flame setting will display on the
remote control screen.
2. Press. The flame effect and all the
functions will turn off. The remote
control screen will go blank.
FLAME
Controls the flame effect. 
Cycles through 5 levels of flame effects.
1. Press once to turn the flame
effect on.
2-4. Press again to cycle through 5
flame effects.
HEATER
Press once turns Fan on, and 10s later Low
heat on. (Pilot lights illuminated ●○)
Press again turns on High heat. (Pilot lights
illuminated ●●)
Press third time turns heat off. 10s later fan
off (Pilot lights illuminated ○○)
1. Press. The heater turns on low
heat.
2. Press. The heater turns on high
heat.
3. Press. Turn off the heat.
4. When the heater is on without
flame or fuel bed, 3rd fuel bed will
light on with 5% brightness to
indicate the heater is on.
TEMP
Controls the thermostat setting.
Thermostat: Automatically turns the heater
on and off to maintain the temperature.
If the thermostat is set below the room
temperature, the heater will turn off.
NOTE: The thermostat only works when the
heater is on.
1) NOTE: The heat will not change as the room
temperature change when there is no
temperature shows on the remote screen.
NOTE: It will change between C and F after
pressing the button for 3s. 60-84F
corresponds to 16-28C. It cannot be
operated in the standby mode, but the
temperature still displays on the remote
control screen.
1. Turn the heat on. Press.
The temperature displays 24C.
2-13. Press again to increase the
temperature by 1C interval up from
16C to 28C (maximum setting).
14. Press again. The thermostat
turns off. No temperature is
displayed.
15. Press. Start at 23C.
TIMER
Controls the timer settings.
The timer turns off the fireplace at the set
time, from 0.5 hours to 9.0 hours.
1-10. Press .
Timer setting: 0.5H,
1.0H, and then each
hour up to 9.0H.
11. Press. Off. No time is displayed.
FUEL
BED
Controls the LED light strips at the bottom of
the fuel bed.
1. Press once to turn the fuel bed
light on.
2-14. Press again to cycle through
14 color options of the fuel bed.

14
CARE AND MAINTENANCE
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this fireplace.
Failure to do so could result in electric shock, fire, or personal injury.
Cleaning
NEVER immerse in water or spray with water. Doing so could result in
electric shock, fire, or personal injury.
Metal:
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage
the metal trim.
Glass:
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-
free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Plastic:
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm
water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch
the surface.
Vents:
Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Clean the exterior of the fireplace with a slightly damp cloth or duster.
Maintenance
Risk of electric shock! DO NOT OPEN! No user-serviceable parts
inside!
ALWAYS turn the heater OFF and unplug the power cord from the
outlet before cleaning, performing maintenance, or moving this fireplace.
Failure to do so could result in electric shock, fire, or personal injury.
Electrical and Moving Parts:
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by
the consumer.
Storage:
Store heater in a clean dry place when not in use.
Replacement parts:
Use only replacement parts supplied by the manufacturer. Use of any other
parts, or modifying the fireplace in any way, will void all warranties.
No internal parts are replaceable or serviceable.

15
In the unlikely event of a problem occurring due to a manufacturing fault within 24
months from the date of purchase of the appliance it will be repaired or replaced free of
charge.
This warranty does not cover consumable items such as the bulbs and fuses which
have a limited lifespan.
If a problem should occur, the nature of the problem together with the date of a
purchase should be immediately reported to the retailer that the appliance was
purchased from. Proof of purchase will be required so the original invoice should be
retained.
Dynasty Fireplaces
#10-3071 No. 5 Road, Richmond, BC V6X 2T4 Canada
Telephone: [phone] Toll free: 1-877-521-1009
WARRANTY